ملخص المحتوى في الصفحة رقم 1
The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126-1196
www.chamberlain.com
®
GARAGE DOOR OPENER
Models PD758DS 3/4 HP
PD758KDS 3/4 HP
For Residential Use Only
Owner’s Manual
■ Please read this manual and the enclosed safety materials carefully!
■ Fasten the manual near the garage door after installation.
®
■ The door WILL NOT CLOSE unless The Protector System is connected and properly aligned.
■ Periodic checks of the opener are required to ensure safe operation.
■ The model
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS Introduction 2-7Adjustment 28-30 Safety symbol and signal word review . . . . . . . . . . . . . . . 2 Adjust the travel limits . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Preparing your garage door . . . . . . . . . . . . . . . . . . . . . . . 3 Adjust the force. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Tools needed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Test the safety reversal system. . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 3
Preparing your garage door Before you begin: • Disable locks. To prevent possible SERIOUS INJURY or DEATH: • Remove any ropes connected to garage door. • ALWAYS call a trained door systems technician if garage door binds, sticks or is out of balance. An • Complete the following test to make sure your garage unbalanced garage door may NOT reverse when door is balanced and is not sticking or binding: required. 1. Lift the door about halfway as shown. Release the • NEVER try to loosen,
ملخص المحتوى في الصفحة رقم 4
Planning Identify the type and height of your garage door. Survey • Do you have an access door in addition to the garage your garage area to see if any of the conditions below door? If not, Model 7702CB Emergency Key Release is apply to your installation. Additional materials may be required. See Accessories page. required. You may fi nd it helpful to refer back to this page • Look at the garage door where it meets the fl oor. Any and the accompanying illustrations as you proceed with gap
ملخص المحتوى في الصفحة رقم 5
Planning (Continued) ONE-PIECE DOOR INSTALLATIONS Without a properly working safety reversal system, • Generally, a one-piece door does not require persons (particularly small children) could be reinforcement. If your door is lightweight, refer to the SERIOUSLY INJURED or KILLED by a closing garage information relating to sectional doors in Installation door. Step 11. • The gap between the bottom of the garage door and • Depending on your door’s construction, you may need the fl oor MU
ملخص المحتوى في الصفحة رقم 6
Carton Inventory Your garage door opener is packaged in one carton which PARTS MAY BE STUCK IN THE FOAM. Hardware for contains the motor unit and all parts illustrated below. assembly and installation is shown on the next page. Accessories will depend on the model purchased. If Save the carton and packing material until installation and anything is missing, carefully check the packing material. adjustment is complete. ® Chain Spreader SECURITY✚ 3-Button Remote Control (2) Motion Detecting D
ملخص المحتوى في الصفحة رقم 7
Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. ASSEMBLY HARDWARE Lock Washer Nut Bolt 1/4"-20x1-3/4" (1) Master 3/8" (1) 3/8" (1) Link (2) Bolt 1/4"-20x2" (1) Lock Nut Washer 1/4"-20 (2) 5/8" (1) Idler Bolt (1) Spacer (1) Trolley Threaded Shaft (1) INSTALLATION HARDWARE Wing Nut Carriage Bolt Nut 5/16"-18 (8) Ring Handle 1/4"-20 (2) 1/4"-20x1/2" (2) Fastener (3) Lag Screw Insulated Hex Bolt Lock Washer 5/16"-9x1-5/8" (2) S
ملخص المحتوى في الصفحة رقم 8
ASSEMBLY STEP 1 Assemble the Rail & Install the Trolley To prevent INJURY from pinching, keep hands and To avoid installation diffi culties, do not run the garage fi ngers away from the joints while assembling the rail. door opener until instructed to do so. The front rail has a cut out “window” at the door end 3. Place the motor unit on packing material to protect (see illustration). The hole above this window is larger the cover, and rest the back end of the rail on top. For on the top of t
ملخص المحتوى في الصفحة رقم 9
ASSEMBLY STEP 2 Fasten the Rail to the Motor Unit To avoid SERIOUS damage to garage door opener, • Insert a 1/4"-20x2" bolt, washer and spacer into the use ONLY those bolts/fasteners mounted in the top of cover protection bolt hole on the back end of the rail the opener. as shown. Tighten securely with a 1/4"-20 lock nut. DO NOT overtighten. Hex Screws 8-32x7/16" • Remove the bolt and lock nut from the top of the motor unit. Chain Spreader • Attach spreader to the motor unit with two
ملخص المحتوى في الصفحة رقم 10
ASSEMBLY STEP 4 Install the Chain/Cable To avoid possible SERIOUS INJURY to fi ngers from 1. Pull the cable around the idler pulley and toward the moving garage door opener: trolley. • ALWAYS keep hand clear of sprocket while operating 2. Connect the cable to the retaining slot on the trolley, opener. as shown (Figure 1): • Securely attach chain spreader BEFORE operating. • From below, push pins of master link bar up through cable link and trolley slot. Dispensing Carton • Push master
ملخص المحتوى في الصفحة رقم 11
ASSEMBLY STEP 5 Tighten the Chain Figure 1 • Spin the inner nut and lock washer down the trolley Outer threaded shaft, away from the trolley. Trolley Lock Nut Threaded Washer • To tighten the chain, turn outer nut in the direction To Tighten Outer Nut Shaft shown (Figure 1). • When the chain is approximately 1/4" (6 mm) above Inner Nut the base of the rail at its midpoint, re-tighten the inner nut to secure the adjustment. To Tighten Inner Nut Sprocket noise can result if chain is t
ملخص المحتوى في الصفحة رقم 12
INSTALLATION STEP 1 OPTIONAL Unfi nished CEILING Ceiling Determine the Header Bracket Location MOUNT FOR HEADER 2x4 Header Wall BRACKET Vertical Centerline To prevent possible SERIOUS INJURY or DEATH: of Garage Door • Header bracket MUST be RIGIDLY fastened to 2x4 Structural structural support on header wall or ceiling, Supports otherwise garage door might NOT reverse when required. DO NOT install header bracket over drywall. • Concrete anchors MUST be used if mounting header bracke
ملخص المحتوى في الصفحة رقم 13
INSTALLATION STEP 2 Wall Mount Install the Header Bracket You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided). WALL HEADER BRACKET INSTALLATION • Center the bracket on the vertical centerline with the Optional Mounting Holes bottom edge of the bracket on the h
ملخص المحتوى في الصفحة رقم 14
INSTALLATION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage fl oor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temporary support to allow the rail to clear the spring. • Position the rail bracket against the header bracket. • Align the bracket holes and join with a clevis pin 5/16"x1-1/2" as shown. Header Wall • Insert a ring faste
ملخص المحتوى في الصفحة رقم 15
INSTALLATION STEP 4 Position the Opener To prevent damage to garage door, rest garage door Follow instructions which apply to your door type as opener rail on 2x4 placed on top section of door. illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid fl at is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder. You will need help Rail at this point if the ladder is not tall enough. • Open the door all the way and
ملخص المحتوى في الصفحة رقم 16
INSTALLATION STEP 5 Hang the Opener To avoid possible SERIOUS INJURY from a falling Three representative installations are shown. Yours garage door opener, fasten it SECURELY to structural may be different. Hanging brackets should be angled supports of the garage. Concrete anchors MUST be (Figure 1) to provide rigid support. On fi nished ceilings used if installing ANY brackets into masonry. (Figure 2 and Figure 3), attach a sturdy metal bracket to structural supports before installing the
ملخص المحتوى في الصفحة رقم 17
INSTALLATION STEP 6 Install the Door Control To prevent possible SERIOUS INJURY or DEATH from Locate door control within sight of door at a minimum electrocution: height of 5 feet (1.5 m) where small children cannot • Be sure power is NOT connected BEFORE installing reach, and away from moving parts of door and door door control. hardware. The installation surface must be smooth and • Connect ONLY to 24 VOLT low voltage wires. fl at. If installing into drywall (Figure 1), drill 5/32" hol
ملخص المحتوى في الصفحة رقم 18
INSTALLATION STEP 7 Install the Lights To prevent possible OVERHEATING of the endpanel or • Press the release tabs on both sides of lens. Gently light socket: rotate lens back and downward until the lens hinge is in • DO NOT use short neck or specialty light bulbs. the fully open position. Do not remove the lens. • DO NOT use halogen bulbs. Use ONLY incandescent. • Install a 100 watt maximum light bulb in each socket. To prevent damage to the opener: Light bulb size should be A19, stan
ملخص المحتوى في الصفحة رقم 19
INSTALLATION STEP 9 Electrical Requirements To prevent possible SERIOUS INJURY or DEATH from To avoid installation diffi culties, do not run the opener electrocution or fi re: at this time. • Be sure power is NOT connected to the opener, and To reduce the risk of electric shock, your garage door disconnect power to circuit BEFORE removing cover opener has a grounding type plug with a third grounding to establish permanent wiring connection. pin. This plug will only fi t into a grounding type
ملخص المحتوى في الصفحة رقم 20
INSTALLATION STEP 10 ® Install The Protector System Be sure power is NOT connected to the garage door The safety reversing sensor must be connected and opener BEFORE installing the safety reversing sensor. aligned correctly before the garage door opener will To prevent SERIOUS INJURY or DEATH from a move in the down direction. closing garage door: IMPORTANT INFORMATION ABOUT THE SAFETY • Correctly connect and align the safety reversing REVERSING SENSOR sensor. This required safety devic
