ملخص المحتوى في الصفحة رقم 1
-J02028 REV. 2010-09-07
REMOTE CONTROL GARAGE DOOR OPENER KITS
GENERAL
Kit Numbers
When installing any electrical accessory, be certain not
91558-01A (Transmitter/Receiver Kit), 91561-01 (Transmitter
to exceed the maximum amperage rating of the fuse or
Kit), 91562-01 (Receiver Kit)
circuit breaker protecting the affected circuit being modi-
fied. Exceeding the maximum amperage can lead to elec-
Models
trical failures, which could result in death or serious injury.
For model fitment information,
ملخص المحتوى في الصفحة رقم 2
9. Press the wall-mounted garage door opener button to test RECEIVER INSTALLATION the button operation. Kits 91558-01A and 91562-01 only VEHICLE PREPARATION 1. Unplug the power cord from the garage door drive unit to prevent door activation during installation. NOTE 2. Select an unswitched 110V power outlet in the garage For vehicles equipped with security siren: located either highest in the garage, closest to the front • Verify that the Hands-Free Fob is present. of the garage, or both. Plug t
ملخص المحتوى في الصفحة رقم 3
For Dyna, Softail and Sportster models: is06667 When servicing the fuel system, do not smoke or allow 2 open flame or sparks in the vicinity. Gasoline is extremely 3 flammable and highly explosive, which could result in death or serious injury. (00330a) 1 3. The fuel tank must be removed or slightly raised to access wiring underneath. See the correct section (Carbureted or EFI Engine) of the service manual for fuel tank bolt removal instructions. If the fuel tank must be removed, follow the inst
ملخص المحتوى في الصفحة رقم 4
2000 and Later Softails, Except Deuce (FXSTD) 2000 and Later Softail Deuce (FXSTD) 1. Remove the fuel tank mounting bolts. See the correct 1. Remove the fuel tank mounting bolts. See the correct section (Carbureted or EFI Engine) of the service manual. section (Carbureted or EFI Engine) of the service manual. 2. Remove the rear splash guard (inner fender) per service 2. Remove the liner from the adhesive backing of the tape manual instructions. pad on the transmitter. 3. See Figure 4. Use cable
ملخص المحتوى في الصفحة رقم 5
is06715 is06716 3 1 2 1. Transmitter mounting location 2. Wires to headlamp Figure 8.Transmitter Mounting Near Fork Tube (FLHR) 3. Ignition module Figure 7.Transmitter Mounting and Wire Routing, (2003 FLHT, FLHX and FLTR Touring Models;Trike Models or Earlier Sportster Models) 1. Remove the outer fairing per the instructions in the service manual. 2004 and Later Sportster Models 2. Remove the liner from the adhesive backing of the tape 1. Remove the fuel tank. See the correct section (Carbureted
ملخص المحتوى في الصفحة رقم 6
is06718 is06721 2 5 1 3 6 4 1 3 2 1. Mount transmitter to fairing 1. Transmitter 2. Headlamp connector 2. Tie transmitter cable to wire casing 3. Orange/white wire 3. Connector with black (ground) and orange wires 4. Black wire Figure 12.Transmitter Mounting (2002-2003 V-Rod Only) 5. White wire 6. Yellow wire 2007 and Later V-Rod Models Figure 10. Wires for Transmitter Connections (FLTR) 1. See Figure 11. Remove the screw (3) fastening the front left louvered cover (1) to the motorcycle. Lift th
ملخص المحتوى في الصفحة رقم 7
9. Insert the rubber boot into the open pin connector of the HARNESS CONNECTION Electrical Connection Harness. General 10. Loosen or remove the four screws holding the ECM to the Splicing of wire leads is necessary in the installation of the mounting bracket. Route the Electrical Connection Harness garage door opener to the vehicle. Find the instructions for a under the ECM connector. Tighten the four screws to specific model in the sections that follow, and refer to the ser- 45-55 in-lbs (5.1-6
ملخص المحتوى في الصفحة رقم 8
2. See Figure 27. Select the correct ring terminal (6 or 7) is02055a from the kit to fit the ground screw. 3. Cut the black wire on the garage door opener wire harness to easily reach the ground location, and crimp the ring terminal to the end of the wire per the Packard crimping 1 tool instructions in the service manual appendix. 3 4. See Figure 5. Install the ring terminal onto the ground screw threads. Fasten the ground screw to the frame and secure per the torque specification in the service
ملخص المحتوى في الصفحة رقم 9
4. Select the 1/4 in. (6.4 mm) ring terminal (7) from the kit. is01103 Crimp the ring terminal onto the black transmitter wire per the Packard crimping tool instructions in the service manual appendix. 1 5. Fasten the black wire ring terminal to the negative terminal mounting post on the battery.Tighten the terminal fastener to 60-96 in-lbs (7-10 Nm). 6. Proceed to the Orange/White Lead Connection section for the specific model. ORANGE/WHITE LEAD CONNECTION TO SWITCHED POWER SOURCE Use the servi
ملخص المحتوى في الصفحة رقم 10
5. Pull only the orange/white wire out of the longer piece of 4. Proceed to the Yellow and White Lead Connections conduit on the garage door opener wire harness. Cut the section for the specific model. excess length from the orange/white wire to within easy 2004-2010 Softail Models reach of the adapter wire. The garage door opener switched power source is an open 6. See Figure 15, the 1 into 1 splice configuration. Use a fuse position on the fuse panel. See the FUSES section of the blue sealed s
ملخص المحتوى في الصفحة رقم 11
NOTE is06729 On some Sportster models the ignition module must be removed to access the orange/white wire in the main harness. 2 3 1. See Figure 20. Carefully slice open an area of the main harness wrap inside the electrical side cover or under the seat at an accessible point, and cut an orange/white main harness power lead. is01106 1 1 2 1. Connector [29A] with orange/white wire 2. White headlamp wire 3. Yellow headlamp wire Figure 21. Wire Splice Locations (2002-2003 V-Rod) 1. Left side cover
ملخص المحتوى في الصفحة رقم 12
kit to splice the white transmitter wire to the white head- is06731 lamp wires. Use the remaining blue sealed splice con- nector to splice the yellow transmitter wire to the yellow headlamp wires. 5. Proceed to the Receiver and Transmitter Programming section to program the garage door opener controls. Softail Models 1. Use cable straps from the kit to fasten the remaining transmitter wires (yellow and white) and conduit to the motorcycle wires leading to the headlamp. Lift the fuel tank as need
ملخص المحتوى في الصفحة رقم 13
lamp wires. Use the remaining blue sealed splice con- is06727 nector to splice the yellow transmitter wire to the yellow headlamp wires. 5. Proceed to the Receiver and Transmitter Programming section to program the garage door opener controls. V-Rod Models 2 1. Cut the yellow and white wires in the main vehicle harness headlamp circuit at an accessible point several inches from the headlamp connector. Cut excess length from the 1 yellow and white transmitter wires if necessary. Trim back the tra
ملخص المحتوى في الصفحة رقم 14
NOTE RECEIVER AND TRANSMITTER Clear all obstructions away from between the transmitter and PROGRAMMING receiver before testing the operation of the garage door opener. After the receiver and transmitter are installed, the receiver 6. Test the garage door opener, and headlamp high beam must be programmed to receive the transmitter frequency.This and low beam operation. process may require two people, depending upon how far apart the receiver and transmitter are during the programming pro- NOTE ce
ملخص المحتوى في الصفحة رقم 15
SERVICE PARTS is06735 1 15 2b 2a 14 6 13 7 12 11 4 5 3 8 9 10 Figure 27. Service Parts, Remote Control Garage Door Opener Kits Table 1. Service Parts, Garage Door Opener Kit 91558-01A Item Description (Quantity) Part Number 1 Transmitter assembly Not sold separately 2a Hardware kit (includes items 3 through 13) 91650-01A 3 • Foam tape, double-sided, 1.0 inch (25.4 mm) x 1.5 inch (38.1 mm) Not sold separately 4 • Sealed splice connector, #18-20 AWG (red) (2) 70585-93 5 • Sealed splice connector,
ملخص المحتوى في الصفحة رقم 16
SERVICE PARTS Table 2. Service Parts,Transmitter Kit 91561-01 Item Description (Quantity) Part Number 1 Transmitter assembly Not sold separately 2b Hardware kit (includes items 3 through 9) 91650-01 3 • Foam tape, double-sided, 1.0 inch (25.4 mm) x 1.5 inch (38.1 mm) Not sold separately 4 • Sealed splice connector, #18-20 AWG (red) (2) 70585-93 5 • Sealed splice connector, #14-16 AWG (blue) (2) 70586-93 6 • Ring Terminal, #18-22 AWG, for 5/16 inch (7.9 mm) stud 9859 7 • Ring Terminal, #18-22 AWG
