ملخص المحتوى في الصفحة رقم 1
CONTENTS
Preparation . . . . . . . . . . . . . . . .2-5
Belt Drive Garage Door Opener Assembly . . . . . . . . . . . . . . . . 6-10
Installation . . . . . . . . . . . . . . 11-20
Models
Install the Door Control. . . . . . 21-23
®
Install the Protector System . . 23-26
HD920EV • 349544 • WD962KEV • WD962KPEV
Power. . . . . . . . . . . . . . . . . . 27-28
Adjustments . . . . . . . . . . . . . 29-31
FOR RESIDENTIAL USE ONLY
Battery Backup. . . . . . . . . . . . 32-33
■ Please read this manual
ملخص المحتوى في الصفحة رقم 2
Preparation Safety Symbol and Signal Check the Door Additional items you may Word Review need for installation: 1 Disable locks and remove any ropes Survey your garage area to see if you will This garage door opener has been designed connected to the garage door. need any of the following items: and tested to offer safe service provided it is 2 Lift the door halfway up. Release the installed, operated, maintained and tested in To prevent possible SERIOUS INJURY door. If balanced, it shou
ملخص المحتوى في الصفحة رقم 3
OT CE Overview/Carton Inventory GARAGE DOOR OPENER ASSEMBLY A. Header bracket B. Pulley C. Door bracket D. Curved door arm E. Straight door arm (Packaged inside rail section) A F. Trolley NOTE: If the inner and outer trolley are packaged seperately, be sure to B assemble the trolley before sliding F onto rail. C Q D G. Emergency release rope and handle H. Rail (1 front and 4 center sections) M I. Hanging brackets (2) E (Packaged inside rail section) G J. Garage door opener K. Sprocket cov
ملخص المحتوى في الصفحة رقم 4
Overview/Carton Inventory ASSEMBLY HARDWARE INSTALLATION HARDWARE H10 H15 H1 Threaded Shaft Lag Screw 5/16"-18x1-7/8" (2) Hex Bolt 5/16"-18x7/8" (4) H2 Bolt 1/4"-20x1-3/4" (2) H16 H4 Self-Threading Screw 1/4"-14x5/8" (2) Lock Nut 1/4"-20 (2) H11 Lag Screw 5/16"-9x1-5/8" (2) H3 H17 Bolt H5 Carriage Bolt 1/4"-20x1/2" (2) Master Link (2) H12 Clevis Pin 5/16"x1-1/2" H18 Wing Nut 1/4"-20 (2) H6 H13 Nut 3/8" (2) H7 Clevis Pin 5/16"x1-1/4" Lock Washer 3/8" H19 Ring Fastener (3) H8 H9 Spring Trolley N
ملخص المحتوى في الصفحة رقم 5
1 Overview/Carton Inventory INCLUDED ACCESSORIES DOOR CONTROL HARDWARE Tools Needed ® Motion-Detecting Smart Control Panel Control Panel Screw Drywall Anchors (2) 6ABx1-1/2" (2) Screw Insulated Staples (30) 6-32x1" (2) Remote Control Screw 5/32 6ABx1-1/4" (2) 3/16 NOTE: Accessories will vary depending on 5/16 the garage door opener model purchased. Depending on your specifi c model, other accessories may be included with your garage door opener. The instructions for these accessories will
ملخص المحتوى في الصفحة رقم 6
Assembly Assemble the rail and trolley 1 1.1 Carefully remove the straight door arm and hanging brackets packaged inside Trolley the front rail. To prevent INJURY from pinching, keep 1.2 Align the rails on a fl at surface as hands and fi ngers away from the joints shown. The front rail has a cut out while assembling the rail. window near the end. Make sure that the larger hole on the front rail is facing up. 1.3 Slide the tapered end of each rail section into the larger end of the rail
ملخص المحتوى في الصفحة رقم 7
Fasten the rail to the garage door opener 2 2.1 Insert the bolt (H2) into the hole on the back end of the rail as shown. Tighten Bolts securely with the lock nut (H4). Do not Sprocket overtighten. To avoid SERIOUS damage to garage “U” Bracket door opener, use ONLY those bolts/ 2.2 Remove the two bolts from the top of fasteners mounted in the top of the the garage door opener. opener. H2 2.3 Place the “U” bracket, fl at side down onto the garage door opener and align the bracket hole wi
ملخص المحتوى في الصفحة رقم 8
Assembly Install the pulley 3 HARDWARE 3.1 Lay the belt beside the rail, as shown. H3 H2 Grasp the end with the hooked trolley Bolt Bolt 1/4"-20x1-3/4" connector and pass approximately 12" H2 (30 cm) of belt through the window. Screwdriver Keep the ribbed side toward the rail, and allow it to hang. 3.2 Remove the tape from the pulley. The Rail center should be greased, if not, re- grease the center of the pulley. H3 3.3 Insert the pulley into the window of the front rail. 3.4 Insert
ملخص المحتوى في الصفحة رقم 9
Install the belt 4 HARDWARE 4.1 Pull the belt around the pulley and H1 H5 toward the trolley. The ribbed side Master Link Threaded Shaft must contact the pulley. 4.2 Hook the trolley connector into the retaining slot on the trolley as shown. 4.3 With the trolley against the screwdriver, dispense the remainder of the belt along the rail length toward the motor unit and around the sprocket. The sprocket teeth must engage the belt. 4.4 Check to make sure the belt is not twisted. Connec
ملخص المحتوى في الصفحة رقم 10
Assembly Tighten the belt and install the sprocket cover 5 5.1 By hand, thread the spring trolley nut 5.2 Insert a fl athead screwdriver tip into on the threaded shaft (H8) until it is one of the nut ring slots and brace it fi nger tight against the trolley. Do not fi rmly against the trolley. To avoid possible SERIOUS INJURY to fi ngers from moving garage door opener: use any tools. • ALWAYS keep hand clear of sprocket while operating opener. Nut ring slot Remove the screwdriver. • Securely
ملخص المحتوى في الصفحة رقم 11
Installation IMPORTANT INSTALLATION INSTRUCTIONS WARNING WARNING To reduce the risk of SEVERE INJURY or DEATH: 1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS. 9. Install wall-mounted garage door control: 2. Install garage door opener ONLY on properly balanced and lubricated garage door. • within sight of the garage door. An improperly balanced door may NOT reverse when required and could result in • out of reach of children at minimum height of 5 feet (1.5 m). SEV
ملخص المحتوى في الصفحة رقم 12
Installation Determine the header bracket location 1 1.1 Close the door and mark the inside vertical centerline of the garage door. OPTIONAL Unfinished Ceiling CEILING 1.2 Extend the line onto the header wall above the door. MOUNT FOR To prevent possible SERIOUS INJURY You can fasten the header bracket within 4 feet (1.22 m) of the left or right of HEADER or DEATH: BRACKET Header Wall the door center only if a torsion spring or center bearing plate is in the way; • Header bracket MUST be
ملخص المحتوى في الصفحة رقم 13
Install the header bracket 2 You can attach the header bracket either to WALL INSTALLATION Option A the wall above the garage door, or to the ceiling. Follow the instructions which will Vertical (Header Wall) work best for your particular requirements. 2.1A Center the bracket on the vertical Centerline of Wall Mount Do not install the header bracket over centerline with the bottom edge of Garage Door 2x4 Structural drywall. If installing into masonry, use the bracket on the horizontal l
ملخص المحتوى في الصفحة رقم 14
Installation Tip: Use the packing material as a Attach the rail to the header bracket protective base for the garage door opener. 3 HARDWARE 3.1 Align the rail with the header bracket. Insert the clevis pin (H12) H19 H12 through the holes in the header Clevis Pin 5/16"x1-1/2" H12 bracket and rail. Secure with the ring fastener (H19). H19 Ring Fastener Position the garage door opener 4 4.1 Remove the packing material and 4.2 Fully open the door and place a Tip: If the door hits the tro
ملخص المحتوى في الصفحة رقم 15
Hang the garage door opener 5 HARDWARE H10 (2) H20 (2) H21 (2) H15 (2) Lag Screw Nut 5/16"-18 Lock Washer Hex Bolt 5/16"-18x1-7/8" 5/16"-18 5/16"-18x7/8" To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural supports of the garage. Concrete anchors MUST be used if installing ANY brackets into masonry. 5.1 On fi nished ceilings, use the 5.2 Make sure the garage door opener 5.3 Cut both pieces of the hanging lag screws (H10) to attach a is ali
ملخص المحتوى في الصفحة رقم 16
NOTICE Installation Install the light bulbs 6 6.1 Pull the top sides of the light lens and rotate the light lens down. or or 6.2 Insert an A19 incandescent or To prevent possible OVERHEATING of the end panel or light socket: compact fl uorescent light bulb (100 • Use ONLY A19 incandescent or compact fl uorescent light bulbs. watt maximum), into the light socket. • DO NOT use incandescent bulbs larger than 100W. 6.3 Rotate the lens up to close. • DO NOT use compact fl uorescent light bulbs lar
ملخص المحتوى في الصفحة رقم 17
FIGURE 1 Install the door bracket 8 A horizontal and vertical reinforcement is needed for lightweight garage doors (fi berglass, aluminum, steel, doors with Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement glass panel, etc.) (not provided). BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. A horizontal reinforcement brace should be long enough to be secured to two or three Figure 1 shows one piece of angle iron as the
ملخص المحتوى في الصفحة رقم 18
Installation Install the door bracket 8 ONE-PIECE DOORS Option B 8.1B Center the door bracket on the top Metal Door H16 of the door, in line with the header (Finished Ceiling) bracket as shown. Top of Door Header Wall Door 8.2B Mark either the left and right, or the (Inside Garage) Bracket top and bottom holes. 2x4 Support Metal Doors: • Drill 3/16" pilot holes and fasten Top Edge of Header Bracket the bracket with the self-threading Door screws (H16) provided. Wood Doors: Opt
ملخص المحتوى في الصفحة رقم 19
Connect the door arm to the trolley 9 IMPORTANT: The groove on the straight ONE-PIECE DOORS Option A door arm MUST face away from the curved door arm. 9.1A Close the door. Disconnect the CORRECT trolley by pulling the emergency release handle. Straight Door 9.2A Fasten the straight door arm and Arm INCORRECT the curved door arm together to the Curved (Groove Door longest possible length (with a 2 or 3 facing out) Arm hole overlap) using the bolts (H15), Straight H20 Door nuts (H
ملخص المحتوى في الصفحة رقم 20
Installation Connect the door arm to the trolley 9 SECTIONAL DOORS Option B 9.1B Close the door. Disconnect the 9.2B Attach the straight door arm to 9.3B Attach the curved door arm to 9.4B Bring arm sections together. Find trolley by pulling the emergency the outer trolley using the clevis the door bracket using the clevis two pairs of holes that line up and release handle. pin (H14). Attach with the ring pin (H13). Attach with the ring join sections. Select holes as far fastener (H19
