ملخص المحتوى في الصفحة رقم 1
®
The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126-1196
www.chamberlain.com
®
GARAGE DOOR OPENER
Models WD952LD
WD952KD
For Residential Use Only
Owner’s Manual
■ Please read this manual and the enclosed safety materials carefully!
■ Fasten the manual near the garage door after installation.
®
■ The door WILL NOT CLOSE unless The Protector System is connected
and properly aligned.
■ Periodic checks of the opener are required to ensure safe operation.
■ The model number label
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS Introduction 2-7 Adjustment 27-29 Safety symbol and signal word review........................2 Program the travel limits ...........................................27 Preparing your garage door ........................................3 Setting the force........................................................28 Tools needed...............................................................3 Test the safety reversal system.................................29 ® Planning ..............
ملخص المحتوى في الصفحة رقم 3
1 Preparing your garage door WARNING WARNING Before you begin: To prevent possible SERIOUS INJURY or DEATH: Disable locks. • ALWAYS call a trained door systems technician if CAUTION WARNING Remove any ropes connected to garage door. garage door binds, sticks, or is out of balance. An unbalanced garage door may not reverse when Complete the following test to make sure your required. garage door is balanced and is not sticking or binding: • NEVER try to loosen, move or adjust garage door, d
ملخص المحتوى في الصفحة رقم 4
— — — — — — — — Planning Identify the type and height of your garage door. Do you have an access door in addition to the Survey your garage area to see if any of the garage door? If not, Model 7702CB Emergency conditions below apply to your installation. Additional Key Release is required. See Accessories page. materials may be required. You may find it helpful to Look at the garage door where it meets the floor. refer back to this page and the accompanying Any gap between the
ملخص المحتوى في الصفحة رقم 5
Planning (Continued) WARNING WARNING ONE-PIECE DOOR INSTALLATIONS Without a properly working safety reversal system, persons (particularly small children) could be Generally, a one-piece door does not require CAUTION WARNING SERIOUSLY INJURED or KILLED by a closing garage reinforcement. If your door is lightweight, refer to door. the information relating to sectional doors in • The gap between the bottom of the garage door and Installation Step 11. the floor MUST NOT exceed 1/4" (6 mm). Otherw
ملخص المحتوى في الصفحة رقم 6
LOCK LIGHT Carton Inventory Your garage door opener is packaged in one carton packing material. Parts may be stuck in the foam. which contains the motor unit and all parts illustrated Hardware for assembly and installation is shown on below. Accessories will depend on the model the next page. Save the carton and packing material purchased. If anything is missing, carefully check the until installation and adjustment is complete. Remote Control Transmitter Visor Clip ® SECURITY 3-Button Remote C
ملخص المحتوى في الصفحة رقم 7
Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. ASSEMBLY HARDWARE Lock Washer Nut Lock Nut Spring/Trolley Nut (1) 3/8" (1) 3/8" (1) 1/4"-20 (2) Bolt 1/4"-20x1-3/4" (2) Master Link (2) Idler Bolt (1) Trolley Threaded Shaft (1) INSTALLATION HARDWARE Carriage Bolt Ring Nut 5/16"-18 (8) Handle Wing Nut 1/4"-20x1/2" (2) Fastener (3) 1/4"-20 (2) Lag Screw Hex Bolt Insulated 5/16"-9x1-5/8" (2) 5/16"-18x7/8" (4) Lock Washer 5/16" (7) Sta
ملخص المحتوى في الصفحة رقم 8
WARNING WARNING ASSEMBLY STEP 1 CAUTION WARNING Assemble the Rail & Install the Trolley To prevent INJURY from pinching, keep hands and fingers away from the joints while assembling the rail. To avoid installation difficulties, do not run the garage door opener until instructed to do so. The front rail has a cut out “window” at the door end 3. Place the motor unit on packing material to protect (see illustration). The hole above this window is the cover, and rest the back end of the rail on top.
ملخص المحتوى في الصفحة رقم 9
WARNING WARNING ASSEMBLY STEP 2 CAUTION WARNING Fasten the Rail to the Motor Unit To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of Insert a 1/4"-20x1-3/4" bolt into the cover the opener. protection bolt hole on the back end of the rail as shown. Tighten securely with a 1/4"-20 lock nut. Do NOT overtighten. Motor Unit Remove the two bolts from the top of the motor Sprocket unit. Place the U bracket, flat side down, on the motor Bolts un
ملخص المحتوى في الصفحة رقم 10
ASSEMBLY STEP 4 WARNING WARNING Install the Belt To avoid possible SERIOUS INJURY to fingers from and Attach the Belt Cap Retainer moving garage door opener: CAUTION WARNING • ALWAYS keep hand clear of sprocket while operating 1. Pull the belt around the idler pulley and toward the opener. trolley. The ribbed side must contact the pulley. • Securely attach sprocket cover BEFORE operating. 2. Hook the trolley connector into the retaining slot on the trolley as shown. 3. With the trolley against
ملخص المحتوى في الصفحة رقم 11
ASSEMBLY STEP 5 Set the Tension • Insert a screwdriver tip into one of the nut ring slots and brace it firmly against the trolley. • Place a 7/16" open end wrench on the square end. Rotate the nut about 1/4 turn until the spring Nut Ring Slot releases and snaps the nut ring against the trolley. Square End This sets the spring to optimum belt tension. You have now finished assembling your garage door opener. Please read the following warnings Trolley before proceeding to the installation section.
ملخص المحتوى في الصفحة رقم 12
Unfinished OPTIONAL INSTALLATION STEP 1 Ceiling CEILING Determine the Header Bracket MOUNT FOR Location HEADER BRACKET 2x4 Header Wall WARNING WARNING Vertical Centerline of Garage Door To prevent possible SERIOUS INJURY or DEATH: 2x4 Structural • Header bracket MUST be RIGIDLY fastened to CAUTION Supports WARNING structural support on header wall or ceiling, otherwise garage door might not reverse when required. DO NOT install header bracket over drywall. • Concrete anchors MUST be used if moun
ملخص المحتوى في الصفحة رقم 13
Wall Mount INSTALLATION STEP 2 Install the Header Bracket UP You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided). Optional Mounting Holes WALL HEADER BRACKET INSTALLATION • Center the bracket on the vertical centerline with Vertical the bottom edge of the bracket o
ملخص المحتوى في الصفحة رقم 14
INSTALLATION STEP 3 Attach the Rail to the Header Bracket NOTE: (Optional) With some existing installations, you may re-use the old header bracket with the two plastic spacers included in the hardware bag. Place the spacers inside the bracket on each side of the rail, as illustrated. • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temp
ملخص المحتوى في الصفحة رقم 15
WARNING WARNING INSTALLATION STEP 4 CAUTION WARNING Position the Opener To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door. Follow instructions which apply to your door type as illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid flat is convenient for setting an ideal door-to-rail distance. Rail • Remove foam packaging. • Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough. • Open
ملخص المحتوى في الصفحة رقم 16
INSTALLATION STEP 5 WARNING WARNING Hang the Opener To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural Three representative installations are shown. Yours CAUTION WARNING supports of the garage. Concrete anchors MUST be used may be different. Hanging brackets should be if installing any brackets into masonry. angled, Figure 1, to provide rigid support. On finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before ins
ملخص المحتوى في الصفحة رقم 17
LOCK LIGHT LOCK LIGHT LOCK LIGHT WARNING WARNING INSTALLATION STEP 6 CAUTION WARNING Install the Door Control To prevent possible SERIOUS INJURY or DEATH from electrocution: Locate door control within sight of door, at a • Be sure power is not connected BEFORE installing door minimum height of 5 feet (1.5 m) where small control. children cannot reach, away from moving parts of • Connect ONLY to 24 VOLT low voltage wires. door and door hardware. If installing into drywall, drill To prevent possi
ملخص المحتوى في الصفحة رقم 18
NOTICE WARNING WARNING INSTALLATION STEP 7 CAUTION WARNING Install the Lights To prevent possible OVERHEATING of the endpanel or light socket: • Press the release tabs on both sides of lens. • DO NOT use short neck or specialty light bulbs. Gently rotate lens back and downward until the • DO NOT use halogen bulbs. Use ONLY incandescent. lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in each Release Tab socket. The lights will turn
ملخص المحتوى في الصفحة رقم 19
INSTALLATION STEP 9 WARNING WARNING Electrical Requirements To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: To avoid installation difficulties, do not run the CAUTION WARNING • Be sure power is not connected to the opener, and opener at this time. disconnect power to circuit BEFORE removing cover to To reduce the risk of electric shock, your garage door establish permanent wiring connection. opener has a grounding type plug with a third • Garage door installation and wiri
ملخص المحتوى في الصفحة رقم 20
INSTALLATION STEP 10 WARNING WARNING ® Install The Protector System Be sure power is not connected to the garage door opener BEFORE installing the safety reversing sensor. The safety reversing sensor must be connected CAUTION WARNING To prevent SERIOUS INJURY or DEATH from a closing and aligned correctly before the garage door garage door: opener will move in the down direction. • Correctly connect and align the safety reversing sensor. This required safety device MUST NOT be IMPORTANT INFORMAT
