ملخص المحتوى في الصفحة رقم 1
D
™
Grow With Me Grow With Me
Grow With Me
RC Rally RC Rally
RC Rally
Model Number 77306
Please keep this instruction sheet for future reference,
as it contains important information.
Requires four "C" (LR14) alkaline batteries for control tower; four "AA"
(LR6) alkaline batteries for car; and one 9V (6LR61) alkaline battery
for remote controller (batteries not included).
Adult assembly is required.
Tool required for assembly:
Phillips screwdriver (not included).
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
ملخص المحتوى في الصفحة رقم 2
Parts Double Flag 2 Flags Handle Ring of Fire Remote Controller Control Holder Tower Ramp Handle Support 4 Stadium Crash Gate Lights Car Remote Controller 2 Ramp Rails Starting Ramp Dirt Track 3 Cones 5 Barrels 3 Hay Flexible Bales Track 5 8 #6 x / " Screw - 7 Label sheet not shown. Shown Actual Size 2
ملخص المحتوى في الصفحة رقم 3
Battery Installation Control Tower Car Battery Compartment Door Battery Compartment Door 1.5V x 4 1.5V x 4 “AA” (LR6) “C” (LR14) Shown Actual Size Shown Actual Size • Locate the battery compartment on the bottom of the car. • Locate the battery compartment on the back of the control tower. • Loosen the screw in the battery compartment door with a Phillips • Loosen the screws in the battery screwdriver. Remove the battery compartment door with a Phillips compartment door. screwdriver. Remove the
ملخص المحتوى في الصفحة رقم 4
Battery Installation Remote Controller • Locate the battery compartment on the back of the remote controller. • Loosen the screw in the battery compartment door with a Phillips screwdriver. Remove the battery compartment door. • Insert one 9V (6LR61) alkaline Battery battery, as indicated inside the Compartment Door battery compartment. • Replace the battery compart- ment door and tighten the screw with a Phillips screwdriver. Do not over-tighten. 9V 9V (6LR61) Shown Actual Size 4
ملخص المحتوى في الصفحة رقم 5
When To Replace Batteries If this toy is working slowly or erratically, it’s likely that batteries need to be replaced. While it is possible that all batteries may need replace- ment, the batteries that will need replacement most often are the batteries in the car, followed by the remote controller, and then the control tower. For more information, see the troubleshooting guide beginning on page 19. Battery Tips • We recommend using alkaline batteries for longer battery life. • Do not mix old a
ملخص المحتوى في الصفحة رقم 6
Assembly WARNING This product contains small parts in its unassembled state. Adult assembly is required. 1 1 1 2 Handle Pegs Double Flag Handle Support Handle Support • Fit the handle onto the handle support as shown. • Position the handle support so 3 the pegs are facing you. • With the checkered side facing down, fit the double flag on to the pegs on the handle support. • Insert three screws through the holes in the handle and into the handle support. Tighten the screws with a Phillips screw
ملخص المحتوى في الصفحة رقم 7
Assembly 4 5 Handle Assembly Control Tower Handle Starting Ramp Pegs Tab Starting Remote Ramp Controller Holder • "Snap" the remote controller • Insert the handle and starting holder onto the tab on the bottom ramp into the matching holes in of the starting ramp, as shown. the control tower as shown. • Insert and "snap" the pegs on • Lift the control tower storage the bottom of the handle compartment door. Insert two assembly into the matching holes screws through the control tower in the starti
ملخص المحتوى في الصفحة رقم 8
Assembly 6 7 Ring of Fire Ramp Ramp Tabs Peg Peg Hole Ramp Ramp Hole Ramp Rail Rail Assembly • Insert and "snap" the tabs on • Gently squeeze the ring of fire the ramp into the matching to insert the pegs on either slots in a ramp rail. end into the matching holes at the top of the ramp assembly, • Repeat this procedure to as shown. attach the other ramp rail. 8
ملخص المحتوى في الصفحة رقم 9
Label Decoration Proper label application will help keep labels looking their best! When applying labels, keep the following guidelines in mind: • Wash hands before applying labels. • Before applying labels, wipe the surface of the toy with a clean, dry cloth to remove dust or oils. • For best results, avoid repositioning a label once it has been applied. • Apply labels as shown in the illustration. One-time assembly is now complete. 4 2 3 4 3 8 11 10 9 7 12 1 5 12 6 9
ملخص المحتوى في الصفحة رقم 10
Mode I - Beginner Driver Mode I is for a beginner or younger driver. Automatic Course Control always keeps the car hugging the track, even over obstacles. Just press the remote controller button to go and release to stop. Setting Up The Track Control Tower End of Track Plug Plug Hint: For best performance, use this toy on a smooth, flat surface. We do not recommend use on a deep, pile carpet. This toy is designed for indoor use only. • Unfold the flexible track into an oval shape and place it be
ملخص المحتوى في الصفحة رقم 11
Mode I - Beginner Driver Ring of Fire Ramp Crash Gate Flag Stadium Light Dirt Track • Note the grooves on the edges of the crash gate, the ring of fire ramp and the dirt track. • Fit the grooves on these three obstacles onto the flexible track. Place the obstacles anywhere you like, but be sure to keep them on the outside of the track, as shown. Hint: For best performance, space the obstacles equally around the course. • Fit the four stadium lights anywhere onto the track. • Fit the two flags
ملخص المحتوى في الصفحة رقم 12
Mode I - Beginner Driver Let’s Go Reset Switch Mode Switch On/Off On/Off Button Button ON/OFF Button IMPORTANT! Be sure the plugs Speed Control Switch on each end of the track are • Slide the mode switch on top fully inserted into the sides of the car to I for beginner of the control tower. driver mode. • Slide the reset switch on the • Locate the speed control switch back of the control tower to on the bottom of the car. the ON position . • Slide the switch to either slow • Press the ON
ملخص المحتوى في الصفحة رقم 13
Mode I - Beginner Driver WARNING To prevent entanglement, keep hair away from wheels. Arrows • Note the arrows on the • Place rear wheels of the car on starting ramp. the starting ramp, making sure the car is pointing in the same direction as the arrows. The car should move around the track counter-clockwise. Listen to the engine revving. 13
ملخص المحتوى في الصفحة رقم 14
Mode I - Beginner Driver • Press the forward button on the remote controller. The car moves around the track, hugging all the way without steering! Hint: The car only travels forward in Mode I - Beginner Driver. The reverse button and the steering Forward wheel also do not work on the remote controller. • You will hear racing sound effects from the control tower each time the car crosses the starting ramp. • Press the forward button on the remote controller. The car moves around the tr
ملخص المحتوى في الصفحة رقم 15
Mode II - Pro Driver Mode II is for a more experienced driver who has acquired better manual skills. In this mode, your child can take full control of steering and direction. For some challenging fun, your child can set up an off road course and use the remote controller wheel to steer around obstacles. Setting Up The Track Mode Switch ON/OFF Button • For off-road fun, place the starting Speed Control Switch ramp, dirt track, ring of fire or • Slide the switch on the top of crash gate in any l
ملخص المحتوى في الصفحة رقم 16
Mode II - Pro Driver Wheel Reset Switch Forward Reverse • Press the forward button on the remote controller.The ON/OFF car moves forward. Button • Press the reverse button on the remote controller. The car • Turn the control tower power moves backward. on to hear sound effects each • Use the wheel on the remote time the car drives over the controller to maneuver around starting ramp. the track or past obstacles. • Be sure the reset switch on the control tower is set to the on Note: The rang
ملخص المحتوى في الصفحة رقم 17
Storage 3 1 Storage Door • Fold up the track, as shown. 4 • Lift the control tower storage compartment door. • Place the barrels, cones, and hay bales (as shown) into the control tower storage compart- ment and door. Close the door. • Slide the track over the starting ramp. 2 Track 5 Track Dirt Track Crash Gate • Remove the flexible track from • Fit the dirt track to the crash both sides of the control tower. gate as shown. 17
ملخص المحتوى في الصفحة رقم 18
Storage 8 6 Hook Control Tower Dirt Track • Attach the car to the hook on • Slide the edges of the dirt track the handle support as shown. into the grooves in the handle support and control tower. 9 7 Ring of Fire Ramp • Fold the ring of fire down onto the ramp. • Fit the ring of fire ramp onto • Fit the stadium lights onto the the dirt track as shown. track as shown. 18
ملخص المحتوى في الصفحة رقم 19
Storage Care • Keep the car tires clean for best performance. 10 • Wipe this toy with a clean cloth dampened with a mild soap and water solution. Do not immerse this toy. • This toy has no consumer serviceable parts. Do not take this toy apart. • Do not drop this toy on a hard surface. • Fit the two flags into the holes in the dirt track as shown. • Place the remote controller in the holder as shown. 19
ملخص المحتوى في الصفحة رقم 20
Adjusting Your Car’s Wheel Alignment If in Mode II your car is not driving in a straight path on smooth surfaces, follow these instructions. Car Pulls 1 to the Right Screw Hole Clockwise • Turn the car over and locate the small screw hole near If your car is pulling to the right: front wheel on the driver’s side. • Insert the small jeweler’s or eye- glass screwdriver into the screw and turn one or two complete Car Pulls 2 turns clockwise. to the Left 3 Place the car on a smooth surface and test
