ملخص المحتوى في الصفحة رقم 1
Owner’s Manual
™
GM ALDL MG2000
Tachometer
IS0195
rev. A ecr#5576 8/2005
ملخص المحتوى في الصفحة رقم 2
IS0195 x7 w/ corrections Mark ups 12/20/05
ملخص المحتوى في الصفحة رقم 3
Index Figure 1 Default screens page 1 Description page 1 Normal Mode page 2 Contrast and Lighting page 2 Displayed Functions page 3 Default screen 1 page 3 Default screen 2 page 3 Default screen 3 page 3 Default screen 4 page 4 Figure 2 Screen Sequence page 4 Figure 3 LCD Display Screens page 5 Edit Mode page 7 Functions that are adjusted in Edit Mode. page 7 Select Default Screen page 7 Reset Fuel Used page 8 Set Fuel Tank Full page 8 Set Amount of Fuel page 9 Organize User Sc
ملخص المحتوى في الصفحة رقم 4
This page left blank intentionally.
ملخص المحتوى في الصفحة رقم 5
The FARIA MG2000 Tachometer combines the features of an ECU serial bus gateway and several instruments into one unit: • The tachometer is analog in appearance but driven by a stepper motor for digital accuracy. • The high resolution LCD screen displays information for many other functions and the various “screens” can be configured as the user wishes. As received, the screens are configured as shown in Fig. 1. The MG2000 receives digital engine data from the Engine Control Unit (ECU) v
ملخص المحتوى في الصفحة رقم 6
(see Figure 2). Press the “Mode” button Normal Mode to exit the “screen selection mode” and When the MG2000 is turned on the unit return to “Normal” mode or do not push will “beep” once, flash once and then the any buttons for 4 seconds and the current unit enters “Self Test” mode. The screen screen will stay selected and the unit will will display “The Self Test Mode Is In return to “Normal” mode (see Figure 3). Operation” for 10 seconds. In the “Normal” operation mode, press the
ملخص المحتوى في الصفحة رقم 7
OIL PRESSURE Analog input. Displays information from the analog oil pressure sender. Default Screen “2” To adjust the lighting intensity of all of the instruments in the system, press and hold both the “Down” and “Up” buttons for 2 seconds. The lighting intensity may now be adjusted by using the “Down” or “Up” buttons. Fuel Left Displays the quantity of fuel remaining in the fuel tank based on the original quantity of fuel in the tank when full and Return to the “Normal” mode by press
ملخص المحتوى في الصفحة رقم 8
Displays the Engine Hours data received from the engine ECU. Default screen “4” LCD Display Screens: In “Normal” mode, press “Mode” once to This screen displays fault conditions enter screen “Select” mode, press “Up” based on engine data received from the or “Down” to move between screens. ECU or alarms based on internally set Press “Mode” once to return to “Normal” alarm points. Engine alarms from the mode. ECU will be displayed as “Check Engine !” Screen “1” or “Engine Emergency S
ملخص المحتوى في الصفحة رقم 9
40 1. Select Default Screen 2. Reset Fuel Used 3. Set Fuel Tank Full 4. Set Amount of Fuel 5. Organize User Screens 6. Select Gauge Range 7. Select Fuel Sender 8. Select Oil Pressure Sender 9. Select Display Units 10. Select Fuel Tank Size 11. Fuel Tank Calibrate 12. Low Fuel Alarm 13. Software ID and Revision 14. Select Self Test Figure 3 Page 5
ملخص المحتوى في الصفحة رقم 10
This page left blank intentionally. Page 6
ملخص المحتوى في الصفحة رقم 11
Functions that are set or adjusted in the Edit Mode “Edit” mode: The “Edit” mode is used to adjust or set the values of numerous functions and 1. Select Default Screen options in the MG2000. The procedure 2. Reset Fuel Used below specifies the steps to be taken 3. Set Fuel Tank Full in the “Edit” mode to adjust / set each option. 4. Set Amount of Fuel To enter “Edit” mode, press the “Mode” 5. Organize User Screens and “Up” buttons while in “Normal” mode 6. Select Gauge Range 7. Select Fuel
ملخص المحتوى في الصفحة رقم 12
Display 1 2 Next 3 Screen Press and hold the “Up” and “Down” buttons for 2 seconds to select this screen as the “default screen” and exit. Press “Up” or “Down” to select another screen. Repeat until desired “Default Screen” is selected. Press “Up” or “Down” to select another function or “Mode” to return to “Normal” mode. 1 Reset Reset “Fuel Used” 2 Fuel 3 Used Press and hold the “Up” and “Down” buttons for 2 seconds to reset “Fuel Used” to zero (0). Press “Up” or “Down” to select another fun
ملخص المحتوى في الصفحة رقم 13
Set 1 Set “Amount of Fuel” 2 Amount 3 Of Fuel NOTE: If a known amount of fuel is in the fuel tank but it is not full, this function can be used to indicate the amount of fuel available. The “Fuel Left” function will then use the amount of fuel entered to calculate the “Fuel Left.” Press and hold the “Up” and “Down” buttons for 2 seconds to select “Current Amount of Fuel.” Press “Up” or “Down” to set the amount of fuel known 1 Fuel to be in the fuel tank. Adjust until the displayed volume
ملخص المحتوى في الصفحة رقم 14
Press and hold the “Up” and “Down” buttons for 2 seconds to save selection for Screen 1, line 1 and advance to Screen 1, line 2. Press “Mode” to exit with no change made. Screen 1 1 Refer to the list of available functions in the ownerʼs manual. Press and hold “Up” or “Down” to select the 2 Line 2 number of the function to be displayed in screen 1, line 2. 3 Item XX Press and hold the “Up” and “Down” buttons for 2 seconds to save selection for Screen 1, line 2 and advance to Screen 1, line
ملخص المحتوى في الصفحة رقم 15
Press and hold the “Up” and “Down” buttons for 2 seconds to select “Oil Pressure Dial.” Press “Up” or “Down” to select another “Gauge Range.” Press “Mode” to return to the “Edit” mode. Press “Up” or “Down” to scroll through the selections. 1 > 60 psi When the correct choice is next to the selection arrow, 2 80 psi Press and hold the “Up” and “Down” buttons for 2 seconds to save the selection and return to “Gauge 100 psi 3 Range” selection 1 Select Select “Coolant Temperature Dial” 2 Coo
ملخص المحتوى في الصفحة رقم 16
Select 1 Select “Water Press Dial” 2 Water Press 3 Dial Press and hold the “Up” and “Down” buttons for 2 seconds to select “Water Press Dial.” Press “Up” or “Down” to select another “Gauge Range.” Press “Mode” to return to the “Edit” mode. Press “Up” or “Down” to scroll through the selections. 1 > 30 PSI When the correct choice is next to the selection arrow, 2 45 PSI Press and hold the “Up” and “Down” buttons for 2 seconds to save the selection and return to “Gauge 60 PSI 3 Range” selec
ملخص المحتوى في الصفحة رقم 17
> USA 1 Press “Up” or “Down” to scroll through the selections. 240 – 33 ohm 2 When the correct choice is next to the selection arrow, EU 3 Press and hold the “Up” and “Down” buttons for 2 4 10 – 180 ohm seconds to save the selection and return to the “Edit” 5 Centroid mode. 6 Press “Up” or “Down” to select another function or “Mode” to return to the “Normal” mode. Select 1 Select “Oil Pressure Sender” 2 Oil Pressure 3 Sender Press and hold the “Up” and “Down” buttons for 2 seconds t
ملخص المحتوى في الصفحة رقم 18
Press “Up” or “Down” to scroll through the selections. 1 > PSI When the correct choice is next to the selection arrow, 2 BAR Press and hold the “Up” and “Down” buttons for 2 3 seconds to save the selection and return to select “Units.” Select 1 Select “Volume Units” Volume 2 3 Units Press and hold the “Up” and “Down” buttons for 2 seconds to select “volume units” Press “Up” or “Down” to select another choice of “Units” Press “Up” or “Down” to scroll through the selections. 1 > GA
ملخص المحتوى في الصفحة رقم 19
Press “Up” or “Down” to scroll through the selections. 1 > Miles When the correct choice is next to the selection arrow, 2 kM Press and hold the “Up” and “Down” buttons for 2 3 NM seconds to save the selection and return to select “Units.” Select 1 Select “Depth Units” 2 Depth 3 Units Press and hold the “Up” and “Down” buttons for 2 seconds to select “Depth Units” Press “Up” or “Down” to select another choice of “Units.” Press “Up” or “Down” to scroll through the selections. 1 >
ملخص المحتوى في الصفحة رقم 20
Select 1 Other 2 If there is no tank size available in the list that matches your tank size, scroll to the next screen. 3 Fuel Tank 4 Size Press “Up” or “Down” to set the fuel tank size displayed 1 Select on the screen to match your fuel tank size. Line 4 value 2 Other will adjust. Fuel Tank 3 When set, Press and hold the “Up” and “Down” buttons XXX G 4 for 2 seconds to save and exit. Press “Up” or “Down” to select another function or “Mode” to return to “Normal” mode. Calibrate 1 Fuel Sele
