ملخص المحتوى في الصفحة رقم 1
EDELBROCK NITROUS SYSTEM
FOR 2005-2007 MUSTANG GT
CATALOG #70410
Table of Contents
Page #
a. Edelbrock General Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
b. Before You Install Your Edelbrock Nitrous System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
c. What is Nitrous Oxide? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 2
Thank You…. …for purchasing an Edelbrock Nitrous Oxide Injection System. Nitrous Oxide injection is one of the most exciting performance enhancements, for the dollar invested, on the market today. With the use of nitrous oxide come some important safety considerations. This manual has been written to help you during the installation and use of your Edelbrock Nitrous System. Please read it completely before you install and use your system. Please pay close attention to the safety information at t
ملخص المحتوى في الصفحة رقم 3
Caution!! Please read this installation manual fully before installing this system. You will need to have available the following tools: Hand Tools: ❑ Socket set including ratchets and extensions ❑ Screwdrivers ❑ Pliers ❑ Bench Vise ❑ Wire Crimping Pliers, Wire Strippers ❑ Floor Jack and Jack Stands ❑ Razor Blade or Other Sharp, Flat Edged Cutting Tool ❑ Safety Glasses Power Tools: ❑ Power Drill ❑ Drill Bits You Should Understand the Following Skills: ❑ Power Tool Safety Procedures ❑ Undercar Sa
ملخص المحتوى في الصفحة رقم 4
1.0 Introduction to your Edelbrock 2005-2007 Mustang GT Nitrous System 1.1 General Information The Edelbrock Performer Nitrous System (Part Number 70410) is designed for the stock to slightly modified 2005 to 2007 Mustang GT. Horsepower and torque increases can vary with equipment upgrades and modifications. The system a plate that is installed in between the throttle body and intake manifold. Both nitrous and fuel are delivered through this nitrous plate. This system includes the bottle (shippe
ملخص المحتوى في الصفحة رقم 5
1.4 Performer Kit Bill of Materials 2 1 19 18 14 15 7-10 20 11 34 5 6 17 16 13 21 12 Qty. Description Item # Qty. Description Item # ❑ 1 2005-07 Mustang Nitrous Plate 1 ❑ 1 Pressure Adapter O-Ring 13 ❑ 1 Gasket 2 ❑ 1 Performer Fuel Solenoid 14 ❑ 2 4AN x 1/8”NPT Straight Fitting, Red 3 ❑ 1 Performer Nitrous Solenoid 15 ❑ 1 4AN x 1/8”NPT Nitrous Filter Fitting 4 ❑ 2 Solenoid Mounting Bracket 16 ❑ 1 3AN x 1/8”NPT Fitting, Blu
ملخص المحتوى في الصفحة رقم 6
2.0 Nitrous System Installation 2.1 Nitrous Bottle Mounting The nitrous bottle is an aluminum cylinder, designed and manufactured to withstand very high pressures. The valve on top of the bottle is a high-flow design that allows easy opening and closing which controls the nitrous flow to the engine compartment. Accurate calibration of your nitrous system depends on the bottle remaining at a stable temperature. In vehicles (such as Corvettes) where the bottle must be mounted in an area subject to
ملخص المحتوى في الصفحة رقم 7
2.2 Bottle Orientation Accurate calibration of your nitrous system depends on the bottle remaining at a stable temperature. Choosing the proper location and orientation for your bottle can greatly affect the overall operation of the nitrous system. Please read the entire bottle mounting instruction section before making your final bottle location decisions. Bottle placement is critical to the performance of your nitrous system. It is important to understand how the bottle valve and siphon tube a
ملخص المحتوى في الصفحة رقم 8
2.4 Nitrous Feed Line Mounting 1. Determine the route your main nitrous feed line will follow. Ensure the path does not route the nitrous feed line too close to the exhaust system, suspension, electrical lines/components or tires. 2. Attach nitrous supply line to bottle. 3. Feed nitrous line along proposed route. 4. Secure nitrous supply line to underside of vehicle. Note: Stainless steel covering of the main nitrous feed line is very abrasive. Shield painted components or sensitive system compo
ملخص المحتوى في الصفحة رقم 9
2.6 Nitrous Plate Installation 1. Disconnect the throttle body from the intake manifold by removing the two nuts from the studs on the lower portion of the throttle body and removing the two bolts from the upper portion of the throttle body. 2. Remove the two studs from the intake manifold. 3. Place the nitrous plate in between the throttle body and intake manifold with the nitrous inlet facing up as pictured below. 4. Place the supplied gasket in between the nitrous plate and throttle body. The
ملخص المحتوى في الصفحة رقم 10
3.0 Electrical System Installation 2 9 12 5 8 11 7 14-16 1 10 4 13 3 6 3.1 Nitrous Electrical Components Bill of Materials (BOM) Item # Qty. Description ❑ 1 1 Wide Open Throttle Module ❑ 2 1 6ft. 16 AWG Wire Assembly, Fused, In-Line (Red) ❑ 3 1 On/Off Round Rocker Switch ❑ 4 2 14/16 AWG Female Spade Connector Nylon Insulated (.187) ❑ 5 4 16/22 AWG Insulated Butt Connector ❑ 6 1 15AMP ATO Blade Fuse ❑ 7 4 18/22 AWG Male Spade Connector Nylon Insulated ❑ 8 3 14/16 AWG Ring Terminal 3/8” Stud N
ملخص المحتوى في الصفحة رقم 11
3.2 Wide Open Throttle Module Wiring Diagram Wide Open Throttle (WOT) Module Nitrous Red Ground Yellow Solenoid Black Blue Fuel Solenoid Throttle Ground Position Fuse Ylw/Wht Sensor w/Holder (Located on Throttle Body) Battery Ground ECM Pin #61 3.3 Nitrous Electrical System Installation Procedure Determine a location for the Wide Open Throttle relay and fuse holder wire. Most common installations locate these components close to the battery. However, these connectors are water-resistant not wate
ملخص المحتوى في الصفحة رقم 12
3.5 Wiring 1. Verify that the battery is disconnected. If it is not, remove the ground strap and place it away from the battery to keep it from shorting out. 2. Locate the red wire with fuse holder and affix it to the red wire on the “WOT” module with the provided butt connector or you can solder the two ends and then heat shrink, if so desired (required soldering iron, rosin core solder and heat shrink not provided in kit). Note: You may need to cut the red wire coming out of the “WOT” module w
ملخص المحتوى في الصفحة رقم 13
4.0 Before You Run Your Vehicle Using Your Edelbrock Nitrous System You have just completed the installation of your Edelbrock Nitrous System. It is time to perform some basic system checks to ensure all of the work you have done is correct and ready to operate properly. The following procedure is designed to validate the operation of your nitrous system before operating your vehicle: Note: Before performing steps 1 through 4, make sure that the nitrous bottle is closed and main nitrous supply l
ملخص المحتوى في الصفحة رقم 14
6.0 Troubleshooting Your Edelbrock Nitrous System How to use our Troubleshooting Flowchart: The troubleshooting of a nitrous system is basic and straightforward. The symptom chart is divided by symptom, cause and action required. Determine your problem (symptom), identify the potential problem (cause) and correct the problem (action required). Symptom #1… There is No change in engine speed when system is activated. 1. Double check to see that the system is wired correctly. a. Compare wiring to s
ملخص المحتوى في الصفحة رقم 15
Symptom #5… Engine detonates heavily when system is activated. Inadequate fuel delivery due to: 1. Plugged fuel filter. a. Inspect fuel filter. i. Clean or replace filter. 2. Crimped fuel line. a. Inspect fuel line. i. Replace crimped line. 3. Weak or inadequate fuel pump. a. Install fuel pressure gauge. Run engine under load at wide-open throttle, with system activated and monitor the pressure. i. Repair or replace fuel pump. ii. Install nitrous dedicated fuel supply. Symptom #6… No change in
ملخص المحتوى في الصفحة رقم 16
Symptom #6… No change in performance when system is activated (Continuation) 9. Loose nitrous solenoid wiring. a. Inspect solenoid wiring. See “Electrical System Installation” section. b. Consult a book concerning proper wiring methods. 10. Malfunctioning nitrous or fuel solenoids. a. Inspect solenoid wiring. See “Electrical System Installation” section. i. Repair wiring. b. Inspect solenoids. See symptom #2. i. Rebuild/replace solenoid. Symptom #7… Engine detonates mildly when system is activat
