ملخص المحتوى في الصفحة رقم 1
PLASMA DISPLAY
ELECT
PS42P2S
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
REMOTE CONTROL
ON-SCREEN MENUS
PICTURE IN PICTURE
TELETEXT
ENG
ملخص المحتوى في الصفحة رقم 2
Safety Instructions ENG Do not place the PDP on an unstable cart, stand, tripod, bracket, table, or floor where it can fall. Do not expose the PDP to extreme temperature conditions or to extreme humidity conditions. Do not expose the PDP to direct sunlight and other sources of heat. Do not expose the PDP to any liquids. Never put objects of any kind into the television, and do not place a water-containing vessel on the PDP. During a storm conditions (especially when there is lightnin
ملخص المحتوى في الصفحة رقم 3
Caution ENG CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ! CAUTION: TO PREVENT ELECTRICAL SHOCK, DO NOT REMOVE REAR COVER, NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash and arrow head The main voltage is indicated on the ☛ within the triangle is a warning sign rear of the PDP and the frequency is alerting you of “dangerous voltage” 50 or 60Hz. inside the product. The exclamation point within the WARNING: TO PREVENT DAMAGE WHICH MAY triangle i
ملخص المحتوى في الصفحة رقم 4
ENG Contents (continued) FOREWORD Safety Instructions .................................................................................................... 2 User Instructions....................................................................................................... 2 Caution ..................................................................................................................... 3 Checking Parts ...................................................................
ملخص المحتوى في الصفحة رقم 5
ENG Contents CONNECTING AND OPERATING A PC Connecting a PC....................................................................................................... 33 Setting up Your Display Plug and Play ..................................................................... 34 Preset Signals........................................................................................................... 34 Setting up Your PC Software..............................................................
ملخص المحتوى في الصفحة رقم 6
Your New Plasma Display Panel ENG Front Panel SPEAKER SPEAKER POWER Remote Control Signal Receiver Press to turn the Aim the remote control towards this spot on PDP on and off. the PDP. SOURCE External input selection. MENU Menu display. - VOLUME + Volume adjustment. SELECT Control the cursor in the Menu. MUTE Temporary sound switch-off. 6
ملخص المحتوى في الصفحة رقم 7
Your New Plasma Display Panel The actual configuration on your PDP may be different, ➢ ENG depending on your model. Rear Panel a) External Speaker Outputs (8Ω ) f) Component2 (480p/576p/720p/1080i) Connect external speakers. Connect a video signal from external sources like Set-top box or DVD players (480p/576p/ b) S-VIDEO Input 720p/1080i). Connect a S-Video signal from an S-VHS VCRs or DVD players. g) Audio Inputs Connect a audio signal from external sources c) VIDEO Input like VCRs, DVD play
ملخص المحتوى في الصفحة رقم 8
Remote Control Buttons Some remote control buttons do not operate with the PDP. ➢ ENG AUTOMATIC SWITCH-OFF VCR/DVD FUNCTIONS; - STOP - REWIND - PLAY/PAUSE/ - FAST-FORWARD PIP FUNCTIONS; - PIP ON/OFF - INTERCHANGE THE MAIN AND THE SUB PICTURE (SWAP) Power - LOCATION SELECTION (LOCATE) - SIZE SELECTION (SIZE) - INPUT SOURCE SELECTION (SOURCE) POWER ON/OFF MAKE THE REMOTE CONTROL WORKS NUMERIC BUTTONS FOR MONITOR, VCR, CABLE, DVD PLAYER EXTERNAL INPUT SELECTION SELECT TO THE PC MODE DIRECTLY TEMPO
ملخص المحتوى في الصفحة رقم 9
Inserting the Batteries in the Remote Control ENG You must insert or replace the batteries in the remote control when you: Purchase the PDP Find that the remote control is no longer operating correctly 1 Remove the cover on the rear of the remote control by pressing the symbol downwards and then pulling firmly to remove it. 2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking care to respect the polarities: + on the battery against + on the remote control - on the battery aga
ملخص المحتوى في الصفحة رقم 10
Installing the Display on the Wall Attachment Panel Wall attachment panel is sold separately. Check with your dealer ➢ ENG 1 Check for the stability of the wall where the PDP is to be installed. If the wall is not enough strong to support the PDP, strengthen the wall before installation. 2 Fix the wall attachment panel on the wall using bolts as shown in the figure: Fixing bolts must protrude from the wall appox. 1.5cm. 3 Using the wall attachment panel, you may adjust the angle of the display f
ملخص المحتوى في الصفحة رقم 11
Installing the Display on the Wall Attachment Panel ENG 4 Remove four large screws from the rear side of the display. Insert the bolts, dish-type washers, and insulation rubber into the four screw-holes as shown in the figure: Bolt Insulation rubber 5 Put the insulation rubber point protruding from the rear top of the display in the groove on the top of the wall attachment panel. Lift up the display a little bit so that the insulation rubber point at the bottom Πof the rear side of the displa
ملخص المحتوى في الصفحة رقم 12
Separating the Display from the Wall Attachment Panel ENG Remove the fixing bolts from both sides (left and right) of the wall attachment panel. Lift and pull the bottom of the display a small amount, to separate the Œ insulation rubber point from the bottom of the wall attachment panel. ´ Lift the display and separate the insulation rubber point from the groove on top of the wall attachment panel. Before Connecting the Display to External Equipment Carefully check the connectors for position an
ملخص المحتوى في الصفحة رقم 13
Connecting Speakers ENG Connect the speaker audio cable to the external speaker output jack on the rear of the PDP matching the “+” and “-” ends of the cable with the diagram on the PDP. The speakers MUST have more than 7watts rating (impedance 8Ω ). ➢ Connecting PDP and Speakers Fix the bracket onto the guide pole located on the rear of speaker Guide pole and fasten the screws. After removing the three screws on the PDP, clamp the speaker and the PDP together and fasten the screws. Guide pole W
ملخص المحتوى في الصفحة رقم 14
Connecting Your VCR or Cable Box ENG Connect a Video/S-Video cable between the Rear panel Video/S-Video output jack on the VCR/Cable box and the Video input jack on the PDP. - For better video, you can use a S-Video cable. Connect an Audio cable between the Audio output jack on the VCR/Cable box and the Audio input jack on the PDP. Videotape Playback 1 Turn on PDP and select the Video or S-Video mode (if S-Video jack is connected) by pressing the Source on the remote control. 2 Turn on your
ملخص المحتوى في الصفحة رقم 15
Connecting a DVD Playar or Set-top Box ENG Rear panel Setop Box DVD Player Connect a Video cable between the Connect a Video cable between the Component Video output jack on the Set- Component Video output jack on the top Box and the Component Video input DVD Player and the Component jack (Component2) on the PDP. Video input jack (Component1 or Component2) on the PDP. Connect an Audio cable between the Audio output jack on the Set-top Box and Connect an Audio cable between the the Audio
ملخص المحتوى في الصفحة رقم 16
Switching On and Off ENG The mains lead is attached to the rear of the PDP. Front panel 1 Plug the mains lead into an appropriate socket. The main voltage is indicated on the rear of the display and ➢ the frequency is 50 or 60Hz. 2 Press the POWER ( ) button on the front panel or remote control to switch the display on. If your Monitor isn’t turned on when the power button is ➣ pressed... press the SELECT button to check if the Monitor mode has been chosen. Viewing the Menus and Displays Your P
ملخص المحتوى في الصفحة رقم 17
Choosing Your Language ENG When you start using your PDP for the first time, you must select the S E T U P language which will be used for displaying menus and indications. Color System Auto Digital NR Off 1 Press the Menu button. Auto Power On On Panel Lock Off Result: The main menu is displayed. Miscellaneous 2 Move the joystick up or down to select the SETUP menu and press Move Enter Exit the joystick button. 3 Move the joystick up or down to select the Miscellaneous me
ملخص المحتوى في الصفحة رقم 18
Using the Various Setup Menus ENG Color System S E T U P You can use your PDP in many countries. Each country ˆ ¤ Color System Auto has its own broadcasting standard. Depending on your Digital NR Off country, the color systems are displayed in the order Auto Power On On given. Panel Lock Off If an abnormal phenomenon appears on the screen ➣ Miscellaneous when Auto is selected, then select the color system manually. Move Select Exit Digital NR If the broadcast signal rec
ملخص المحتوى في الصفحة رقم 19
Using Automatic Picture Settings ENG You can select the picture effect which best corresponds to your P I C T U R E viewing requirements. The following picture effects are available in Select ˆ Custom ¤ the order given: Contrast Custom, Standard, Sports, Movie, Mild, Dynamic. Brightness Sharpness Color In the PC mode, you can select Custom, High, Middle or Low. ➣ Color Tone Normal Move Select Exit 1 Press the Menu button, then press the joystick b
ملخص المحتوى في الصفحة رقم 20
Customizing the Picture ENG Your PDP has several settings which allow you to control picture P I C T U R E quality: Select Custom Contrast, Brightness, Sharpness, Color, Contrast Color Tone, Tint (NTSC only). Brightness Sharpness Color When the Select is set to Custom, the following settings can ➣ Color Tone Normal be adjusted. Move Adjust Exit 1 Press the Menu button, then press the joystick button to enter the PICTURE menu. Contrast
