Apollo Actuators AE-Series دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

APOLLO AE-SERIES ELECTRIC ACTUATORS
General Installation, Operation, Specifications, Maintenance and Trouble Shooting Instructions
The following is intended as a guide only in installing and operating the electric actuator. The
manufacturer assumes no liability whatsoever for any personal injury or other special or consequential
damages that may occur. There are no warranties as to suitability for a specific application or purpose.
Installation / Mechanical Operation
• Verify that the valve br

ملخص المحتوى في الصفحة رقم 2

Actuator Breakaway Cycle Duty Model Torque Time Cycle* Amperage Draw (max.) Output 90° Starting or locked rotor current voltage (in.-lbs.) Travel (50% 24 VAC 115VAC 230VAC 12VDC 24VDC Load) AE200 200 in-lbs. 5.0 sec. 25% 4.56 .74 amp .44 amp 2.00 1.38 amp amp amp AE400 400 in-lbs. 10.0 sec. 25% 4.56 .74 amp .44 amp 2.00 1.38 amp amp amp AE600 600 in-lbs. 15.0 sec. 25% 4.56 .74 amp .44 amp 2.00 1.38 amp amp amp AE800 800 in-lbs. 20.0 sec. 25% 4.56 .74 amp .44 amp 2.00 1.38 amp amp amp AE1000 1000

ملخص المحتوى في الصفحة رقم 3

24/115/230 VAC Wiring Diagram SUGGESTED CONTROL WIRING (CUSTOMER SUPPLIED). POSITIION INDICATOR JUNCTION 1-2 AND 1-5. (CUSTOMER SUPPLIED). 115 VAC LINE VOLTAGE CLOSED POSITION SWITCH (TOP)

ملخص المحتوى في الصفحة رقم 4

OPEN POSITION SWITCH (BOTTOM) OPTIONAL MOTOR RREAK TERMINALS 6-12 ARE USED FOR OPTIONAL LIMIT SWITCHES OR HEATER & THERMOSTAT OPTIONAL 15 WATT 115 VAC HEATER & THERMOSTAT LINE VOLTAGE W1 W2 F1 OPTIONAL 24 VAC 60 HZ 1 PH RED BLUE 5 AMP 115 VAC 60 HZ 1 PH RED BLUE 1 AMP 230 VAC 60 HZ 1 PH YELLOW BLUE .75 AMP DUE TO HIGH AC INDUCTION FEEDBACK VOLTAGE THROUGH THE CAPACITOR AND TERMINALS 3 & 4, MULTIPLE ACTUATORS CANNOT BE WIRED IN PARALLEL. SEPARATE RELAYS (ISOLATED CONTACTS) MUST BE PROVIDED FOR E

ملخص المحتوى في الصفحة رقم 5

12/24 VDC WIRING DIAGRAM ON-OF-ON DPDT SW. SUGGESTED CONTROL WIRING (CUSTOMER SUPPLIED) (CUSTOMER SUPPLIED). 115 VAC LINE VOLTAGE

ملخص المحتوى في الصفحة رقم 6

CLOSED POSITION SWITCH (TOP) RED +TERM MOTOR – TERM BLACK OPEN POSITION SWITCH (BOTTOM) TERMINALS 6-12 ARE USED FOR OPTIONAL LIMIT SWITCHES OR HEATER & THERMOSTAT OPTIONAL 15 WATT 115 VAC HEATER & THERMOSTAT LINE VOLTAGE W1 W2 F1 OPTIONAL 12 VDC ORANGE BLUE 3 AMP 24 VDC BROWN BLUE 1.5 AMP MANUAL OVERRIDE SHAFT .312 SQUARE CPTIVE SCREWS ARE 1/4” – 20 UNC SOCKET HEAD CAP SCREWS, 6 PLACES INDICATOR – SHOWN IN CLOSED POSITION 1/2” NPT, TYPICAL BOTH SIDES 3.5” CLEARANCE (FROM TOP OF OVERRIDE SHAFT)

ملخص المحتوى في الصفحة رقم 7

AE-SERIES DIMENSIONS

ملخص المحتوى في الصفحة رقم 8