ملخص المحتوى في الصفحة رقم 1
Model APS-787C
Owner's Manual
5 Button Remote Start Security System With
Plug-In Shock Sensor & Starter Disable
FEATURES:
2 Five Button Programmable RF Transmitters
Seven Channel Code Learning Receiver (capable of accepting 4 transmitters)
Code Hopping Technology
Selectable Manual Override Mode
Remote Panic in all modes
Protected Push Button Valet/Override Switch In Windshield Receiver
External Superheterodyne Receiver Antenna w/PushButton Switch & LED
Selectable Automatic Timed
ملخص المحتوى في الصفحة رقم 2
Your Remote Start Alarm System has many features and available options some of which are selected at time of installation. For your reference, the list on page 9 of this manual shows what features and options have been installed. Consult your installing dealer for options that may have been installed and are not listed. YOUR " CODE HOPPING " TRANSMITTERS: The transmitters included with your new remote start system use the most advanced and secure form of radio frequency transmission available o
ملخص المحتوى في الصفحة رقم 3
ARMING THE SYSTEM - PASSIVE (AUTOMATIC) If the passive arming feature has been selected: 1. Turn the engine off, exit the vehicle, and close all doors, hood and trunk. The dash mounted LED will begin to flash rapidly indicating that the 30 second passive arming timer has begun. If the LED does not begin to flash rapidly, then you have left a door, hood, or trunk ajar. Closing this entry point will allow the arming cycle will begin. If any entry point is opened during the 30 second arming cycle,
ملخص المحتوى في الصفحة رقم 4
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock transmitter button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. If your transmitter has a sperate lock unlock buttons, pressing the unlock button anytime after the first unlock command will cause all the vehicle doors to unlock. SILENT DISARMING 1. As you approach the vehicle, press and hold the disarm button of your key chain transmitter fo
ملخص المحتوى في الصفحة رقم 5
mode, the system must first be disarmed either by using your keychain transmitter, or by activating your personalized manual override code. 1. Enter the vehicle, and turn the ignition key to the on position. 2. Press and hold the Push-Button switch until the LED turns on solid. The system will remain in the valet mode. 3. To return to normal operation, press and release the Push-Button switch any time the ignition is on. NOTE: Always remember to return the vehicle to the valet off position. This
ملخص المحتوى في الصفحة رقم 6
Custom Code Programming Example: To Change the code from the factory pre-assigned code of 11 to “52” you would do the following: 1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. 2. Turn the ignition switch to the on position. 3. Within 10 seconds, press and release the Receivers Push-button switch, 3 times. 4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.) 5. With
ملخص المحتوى في الصفحة رقم 7
NOTE: If the vehicle battery is disconnected then reconnected, the unit will return to the default setting of chirps on. Repeat the above procedure to eliminate the arm/disarm chirps. REMOTE PANIC OPERATION The Lock or Unlock button on your keychain transmitter also functions as a panic switch for use in emergency situations. To use remote panic, 1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more seconds. The alarm will immediately sound. 2. To stop the alarm,
ملخص المحتوى في الصفحة رقم 8
If your parking lights flashed four times, this indicates the turbo mode was on and is now turned off. With the turbo timer mode selected on, after you've arrived at your destination, while the engine is still running, set the parking brake, pause 2 seconds, then turn the ignition switch to the off position. The engine will continue to run the allotted time according to the selection during installation. If you do not want the vehicle to continue to run for one cycle, simply step on the vehicle'
ملخص المحتوى في الصفحة رقم 9
TO BEGIN THE AUTOMATIC START UP TIMER 1. Turn the ignition key on then off. 2. Within 10 seconds, activate the RF start command two times. (Push the trunk/key button of your keychain transmitter 4 times). The parking lights will flash and the siren will chirp 4 times indicating the timed start mode is activated. The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for the pre-pro- grammed time (5,10,15 or 20 minutes), and then shut off. This will continue for 48 hours.
ملخص المحتوى في الصفحة رقم 10
ADDITIONAL REMOTE FUNCTION (CHANNEL 5) This system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are: Remote Trunk Release Remote Window Closure Rear Hatch Release Right Or Left Slider Doors in An Equipped Van To activate the optional accessory, press the option button on the keychain transmitter. The optional accessory will immediately engage. ADDITIONAL REMOTE FUNCTION (CHANNEL 6) This system
ملخص المحتوى في الصفحة رقم 11
Page 11 128-8778 11 of 12
ملخص المحتوى في الصفحة رقم 12
APS-787C SYSTEM FUNCTIONS AT A GLANCE ALARM DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH... PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 ALARM SIREN CHIRP INDICATION 1 CHIRP* = ARM 2 CHIRPS* = DISARMED 3 CHIRPS = ARMING WITH ENTRY POINT OPENED 4 CHIRPS = DISARM AFTER INTRUSION 5 CONTINUOUS = TRIGGERED/PANIC ALARM PARKING LAMP INDICATIONS 1 FLASH = ARM 2 FLASH = DISARM 3 FLA
