Audiovox PRO 9232 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Model PRO 9232
INSTALLATION INSTRUCTIONS
KEYLESS ENTRY ALARM UPGRADE MODULE
PRE - INSTALLATION NOTES :
This system provides an output that is used to drive the siren, and an output that can pulse the vehicle's horn. When
utilizing the horn, an additional relay maybe required. Caution: on many vehicles the factory horn is not
designed for continuous use, and it is recommended that the siren is used for these vehicles. Check to see
if the horn in the vehicle is the same part that is used in a veh

ملخص المحتوى في الصفحة رقم 2

INSTALLATION OF MAJOR COMPONENTS : ALARM CONTROL MODULE Select a mounting location inside the passenger compartment ( up behind the dash ), and secure it using screws, or cable ties. Do not mount the control module in the engine compartment, as it is not waterproof. Do not mount the unit or route the wiring near the steering shaft, as it might become entangled preventing proper operation of the vehicle. L.E.D.& VALET / OVERRIDE SWITCH ASSEMBLY The LED & Valet/Override switch assembly are provi

ملخص المحتوى في الصفحة رقم 3

It is recommended that when installing this system into vehicles with electronic “ after fans, “ the procedure for hardwire should be followed. HARDWIRE: When hardwiring the door trigger input to switches at all points of entry, the voltage sense circuit must be disabled. By default, programmable feature # 6 is set to "Hardwire" therefore no change is required. If however you are setting the unit as a voltage sensing alarm, feature #6 must be changed and voltage sensing must be turned on. WHIT

ملخص المحتوى في الصفحة رقم 4

LIGHT GREEN WIRE : (-) INSTANT TRIGGER ZONE 1 This is an instant activation ground trigger wire. This wire should be reserved for connection to optional ground output trigger devices such as motion, glass breakage and/or non plug in shock sensors. DARK GREEN WIRE : (-) INSTANT TRIGGER ZONE 2 This is an instant activation ground trigger wire. It should be connected to the previously installed hood and trunk pin switches. GREEN w/BLACK TRACE WIRE : AUXILIARY OR REMOTE STARTER OUTPUT This wire pro

ملخص المحتوى في الصفحة رقم 5

RED w/BLACK TRACE WIRE : DISARM INPUT #2 Connect this wire to the unlock side of the door lock/unlock switch or any passenger door unlock motor wire, which will receive a negative or positive pulse when all doors are unlocked using the door panel switch or the remote transmitter, but will not receive a pulse when the driver only door is unlocked using the remote transmitter. BLUE WIRE : TRUNK TRIGGER SHUNT INPUT This wire will determine if the vehicle’s trunk has been opened using the OEM trans

ملخص المحتوى في الصفحة رقم 6

The factory default settings for the selectable features are: Feature #1 = 1 Chirp, 1 Flash, 800ms door lock, 800ms door unlock. Feature #2 = 2 Chirps, 2 Flash, Auto Locks Off Feature #3 = 2 Chirps, 2 Flash, Auto Unlock Off Feature #4 = 2 Chirps, 2 Flash, Active Locks Feature #5 = 1 Chirp, 1 Flash, Passive Arming Feature #6 = 1 Chirp, 1 Flash, Hardwire Feature #7 = 1 Chirp, 1 Flash, Door Trigger Instant. Feature #8 = 2 Chirps, 2 Flash, Two Wire Disarm. If it is necessary to change the de

ملخص المحتوى في الصفحة رقم 7

Delay Select. Siren/Horn Chirp 7x, Light Flash 7x, LED Flashes 7x Pause, 7x Pause, indicating feature 7 selected. Use Factory Lock button of transmitter or the factory door lock switch to select. 1 Chirp, 1 Flash = Door Trigger Instant 2 Chirp, 2 Flash = Door Trigger Delay 8. Press and release valet push-button switch 1x to advance to feature #8, one wire or two wire disarm select. Use Factory Lock button of transmitter or the factory door lock switch to select. 1 Chirp, 1 Flash = 1 Wire Disar

ملخص المحتوى في الصفحة رقم 8

Printed in Taiwan © 1998 Audiovox Corp., 150 Marcus Blvd. Hauppauge, N.Y. 11788 Form No. 128-5408