Audiovox PRO 9845 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Model PRO 9845
Installation Manual
Keyless Entry System
With Two Auxiliary Outputs
Installation Instructions
This Unit Is Intended For Installation In Vehicles With
12 Volt Negative Ground Electrical Systems Only.
Kit Contents:
PRO 9845 Control Module
(2) - Two Button Transmitters
4 Channel Code Learning Receiver
On Board Antenna
(1) - Multi Pin Input/Output Harness
(1) - Three Pin Door Lock Harness
(1) - Two Pin LED Indicator
(1) - Two Pin Valet / Override Switch
(1) - 10 Amp In-line Fuse Hold

ملخص المحتوى في الصفحة رقم 2

The PRO 9845 Keyless Entry System is designed to provide a convenient electronic means to gain access to the vehicle by providing RF remote control over the vehicle's power door lock system. The unit also includes outputs to control the vehicle's dome lights, as well as exterior parking lights. Although not an alarm system, the PRO 9845 also incudes a starter interrupt circuit output. It also includes two additional auxiliary outputs designed to allow for control over optional devices such as

ملخص المحتوى في الصفحة رقم 3

NOTE: Some vehicles, (mostly European) have isolated "left" and "right" side parking lights. To connect to the parking light systems in these vehicles, you must use a separate SPDT relays to connect to each side in order to keep them isolated. Attach the WHITE wire of the system to this point. BROWN Wire: Negative (-) Door Trigger Input Wire grounding door pinswitches (typical of most GM, Chrysler, and If the vehicle's interior lights are controlled by import vehicles), the Brown negative door

ملخص المحتوى في الصفحة رقم 4

GREEN/BLACK Wire: Immediate, 300mA Duration of Transmit, Channel 3 Output The Green/Black wire supplies a 300mA switched output whenever Channel 3 of the receiver is accessed. Pressing both transmitter buttons simultaneously will access Channel 3 and will remain active for as long as the transmitter button(s) is held. This is a low current output and must be connected to a relay to supply power to the device you intend to control. Connect Green/Black Trace wire to terminal #86 of a VF45F11 P&

ملخص المحتوى في الصفحة رقم 5

DASH MOUNTED LED 2PIN White Plug w/2 Wires; Red & Blue The Red & Blue wires in the 2PIN mini white connector control the anode and cathode of the dash mounted LED. Route the twin lead Red and Blue wires from the LED to the control unit and plug the two pin connector into the mating white mini connector shell of the control module. Do not force the connector, it will only plug in one way. VALET/PROGRAM/MANUAL OVERRIDE SWITCH 2PIN Blue Plug w/2 Wires; Black & Gray The Black & Gray wires in the 2P

ملخص المحتوى في الصفحة رقم 6

Upon entering the Programming Mode, the system is immediately set to allow adjustment of the First Programmable Feature. That First feature, "Passive or Active Arming", can then be set ON or OFF by pressing button 1 of the transmitter. The system confirms that it is set to adjust the First feature by repeatedly flashing the LED once, with a pause in between each flash. The system will then report how the feature has been set by the number of chirps heard after pressing the transmitter button.

ملخص المحتوى في الصفحة رقم 7

FEA TURE A CTION TO PERFORM RESPONSE FROM SYSTEM LED FLA SH PA TTERN To Turn the Ignition Switch ON LED Turns OFF Enter Toggle the Valet/Program/Manual Override Switch The ON then OFF 3 Times 1 Siren/Horn Chirp & 1 LED Flash Programming Within 3 seconds, M ode turn the Ignition Switch OFF, then ON 1 Short Chirp, and 1 Long Chirp You have now engaged the Programming M ode, and are set to adjust the First feature This mode will time out automatically in 15 seconds, or can be cancelled by turning

ملخص المحتوى في الصفحة رقم 8

(-) (+) (+) (-) © 2001 Audiovox Corp. 128-5452B