Audiovox CCDLF دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Model CCDLF
License Plate Rearview Camera
with Non-Reversed Image
CCDLF FEATURES:
• Built Into License Plate Frame
• High Resolution, 1/3” CCD Color Camera
• Compact Zinc Alloy Die Cast Body
• Waterproof Housing
• Waterproof Microphone
O
• 150 Wide Angle View
• Non-Reversed Image
1
128-7729
1 of 8

ملخص المحتوى في الصفحة رقم 2

CONTENTS ITEM FIGURE QUANTITY LICENSE PLATE WITH 1 NON REVERSED CAMERA CAMERA ANGLE 1 ADJUSTMENT WEDGE THEFT-PROOF SCREWS 2 THEFT-PROOF SCREWS 2 FUSE (1A) 1 CAMERA MOUNTING BOLT 2 ANTI-THEFT ALLEN KEY 1 EXTENSION CABLE 1 DIELECTRIC GREASE 1 PACKET HEAT SHRINK TUBING 1 2 128-7729 2 of 8

ملخص المحتوى في الصفحة رقم 3

Color Camera View: Cable Connector End View: 3 128-7729 3 of 8

ملخص المحتوى في الصفحة رقم 4

The CCDLF camera has a non-reversed image. This camera can be used with Audiovox LCD rear view mirrors and the LCM45NB. It can also be used with multimedia systems that reverse the backup camera image. Installation. 1. Locate suitable location near the vehicles rear license plate to route the camera cable. The camera cable can be routed through an existing grommet or use a location where a 5/8” hole can be drilled. Be sure to check behind intended drilling location. Check for camera interfer- en

ملخص المحتوى في الصفحة رقم 5

If using Audiovox LCD rearview mirror or LCM45NB, use the extension cable supplied with the monitor. 5. Connect the Camera cable to the extension cable (supplied). Route the extension cable up to the intended monitor. Connect as follows: a. Black wire- connect to chassis ground b. Red wire- connect to 12V accessory wire c. Yellow RCA- connect to Video input d. Red RCA- connect to audio input (if equipped) When the connection of the Camera and Extension Cable is outside of the vehicle, (such as a

ملخص المحتوى في الصفحة رقم 6

2. If you see too much bumper, the downward angle must be decreased. Place the thin edge of the wedge on top between the camera and frame. 3. If you cannot see the bumper at all, the downward angle must be increased. Place the thin edge of the wedge on the bottom between the camera and frame. Camera Installation 1. LICENSE PLATE 2. CAMERA ANGLE ADJUSTMENT WEDGE 3. CAMERA 6 128-7729 6 of 8

ملخص المحتوى في الصفحة رقم 7

Specifications: 1. Image Device : 1/3” CCD with 10 Bit A/D Digital Signal Processor. 2. Signal System: CCDLF NTSC, Standard image. 3. Total Effective Pixels: NTSC:537(H)*505(V). 4. Resolution: Greater than 250,000 pixels Greater than 420 TV Lines. 5. Power source : DC12V 6. Video Output:1.0Vp-p Composite( 75 ohm load). 7. Low Lux Sensitivity :0.2 Lux 8. S/N Ratio : More than 48db. 9. Current: 80mA o o o o 10. Operating Temperature: -13 F to 158 F (-25 C to 70 C) 11. Wide Angle View : Diag

ملخص المحتوى في الصفحة رقم 8

© 2006 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-7729 8 128-7729 8 of 8