Acura Music Link 2007 RDX iPod Kit دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

Accessory Application Publications No.
BII 32604-34945
INSTALLATION
ACURA MUSIC LINK™
2007 RDX Issue Date
®
(FOR iPod )
INSTRUCTIONS
MARCH 2007
PARTS LIST Acura Music Link Adapter Kit (sold separately)
P/N 08A28-1H2-100
Acura Music Link Adapter (sold separately)
P/N 08A28-1H1-800
Acura Music Link unit
4 Cushion tapes
Bus cable
Holder cushion
Music Link harness
Grommet
(Not used)
CD-ROM
8 Wire ties
(for home computer
use only)
2 Long wire ties
Quick reference guide
Y-Harness Adapter (sold separa

ملخص المحتوى في الصفحة رقم 2

3. Open and lower the glove box, disconnect the TOOL AND SUPPLIES REQUIRED damper, then push in on the side of glove box to #2 Phillips screwdriver open it past the stoppers. Diagonal cutters Ratchet 10 mm Socket Shop towel DAMPER Illustration of the Acura Music Link Installed on the Vehicle Push. MUSIC LINK UNIT Push. MUSIC LINK HARNESS GLOVE BOX 6204021B 4. Remove the right center console side trim (four clips). CLIPS (4) BUS CABLE 6206032B INSTALLATION Client Information: The information in t

ملخص المحتوى في الصفحة رقم 3

6. Lift up the shift lever trim (six retaining tabs). 8. Open the center console, then remove the beverage holder (six clips). CLIPS (6) BEVERAGE HOLDER SHIFT LEVER TRIM RETAINING TABS (6) 6204050B 7. Remove the left center console side trim (three 6204071B clips). 9. Remove the pocket (two self-tapping screws) and three vehicle connectors. LEFT CENTER CONSOLE SIDE TRIM VEHICLE CONNECTORS CLIPS (3) POCKET 6204061B SELF-TAPPING SCREWS (2) 6204081B © 2007 American Honda Motor Co., Inc. - All Right

ملخص المحتوى في الصفحة رقم 4

10. To prevent scratching the shift lever and trim, Routing The Harness cover them with a shop towel. 12. Insert the Music Link unit into the holder cushion. HOLDER CUSHION MUSICLINK UNIT SHIFT LEVER SHOP TOWEL Align ends. 6417010B 5426010B 13. Connect the bus cable DIN connector (black) and 11. Remove the audio unit (four bolts) and the Music Link harness DIN connector (white) to disconnect the five vehicle connectors. the Music Link unit. NOTE: The antenna connector release is on the side of t

ملخص المحتوى في الصفحة رقم 5

14. Apply a cushion tape around the bus cable DIN 16. Get the Y-harness adapter cable. Connect one connector (black) and Music Link harness DIN end of the bus cable 14-pin connector to the connector (white). Secure the Music Link unit to Music Link, and the other vehicle 14-pin the front side of the vehicle frame using two long connector to the Y-harness adapter connector. wire ties. If the Music Link unit is not in front of BUS CABLE the frame there will not be clearance for the VEHICLE 14-PIN

ملخص المحتوى في الصفحة رقم 6

19. Bundle the excess bus cable, and wrap one wire 22. Put the Music Link harness in the glove box as tie around the bus cable. shown and position the glove box to its original position. Reconnect the damper to the glove box. VEHICLE BUS CABLE HARNESS (Bundle the excess.) WIRE TIE DAMPER MUSIC LINK GLOVE BOX HARNESS 23. Check that all wire harnesses are routed properly and all connectors are plugged in. 6206022B WIRE TIE 24. Reinstall the pocket, the beverage holder, the left and right side trim