Metra Electronics 95-5820 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

INSTALLATION INSTRUCTIONS FOR PART 95-5820
APPLICATIONS
FORD
F-150 2009
95-5820
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
• A) Double DIN Radio Housing • B) Double DIN Radio Housing Brackets
• C) Radio Housing Trim Panel • D) (6) U Style Panel Clips
A
D
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
Harness:
• Please see www.metraonline.com for
specific interface harness
Antenna Adapter:
C • 40-CR10 - Chrysler antenna adapter 02-u

ملخص المحتوى في الصفحة رقم 2

95-5820 TABLE OF CONTENTS Dash Disassembly - FORD F-150 2009 .... ... .... ... .... .... ... .... ... . . 1,2 Kit Preparation - FORD F-150 2009 .... .... ... .... ... .... ... .... ... ....3 Kit Assembly - Double DIN Radio Provision / Stacked ISO Mount Units Provision . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installati

ملخص المحتوى في الصفحة رقم 3

95-5820 DASH DISASSEMBLY FORD F-150 2009 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the switch panel to the right of the cigarette lighter then remove the (1) 9/32” screw exposed. (Figure A) 3 Remove the rubber pad at the top of the radio trim panel then remove the (2) 9/32” screws exposed. (Figure B) 4 Unclip and pull the side panels con- B taining the a/c vents away from the radio trim panel. Note: It is not nec- essary to remove t

ملخص المحتوى في الصفحة رقم 4

95-5820 DASH DISASSEMBLY FORD F-150 2009 E 6 Unclip and remove the hazard/airbag switch assembly from the factory radio trim panel. (Figure E) 7 Unclip and remove the cigarette lighter socket from the radio trim panel. (Figure F) 8 Remove (4) Torx screws securing the factory climate control to the radio trim panel. (Figure G) F 9 Remove (4) 9/32” screws to remove the factory radio. Continue to final preparation. G FACTORY RADIO TRIM PANEL-REAR VIEW 2

ملخص المحتوى في الصفحة رقم 5

95-5820 KIT PREPARATION FORD F-150 2009 A 1 Clip the hazard/airbag switch assembly into the radio housing in the same location as the factory radio trim panel. (Figure A) 2 Clip the cigarette lighter socket into the radio housing in the same loca- tion as the factory radio trim panel. (Figure B) 3 Secure the climate control into the radio housing using the factory hardware in the same location as B the factory radio trim panel. (Figure C) 4 Attach the (6) U style panel clips to the radio housi

ملخص المحتوى في الصفحة رقم 6

95-5820 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION OR STACKED ISO MOUNT UNIT(S) PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Slide the appropriate side bracket A over the mounting legs of the Double DIN trim plate aligning the holes in the trim plate and the bracket and rotate inward. Note: The notch in the housing should be on top. (Figure A) 2 Slide the Double DIN or stacked ISO mount units into the bracket/radio housing assembly and secure the Double

ملخص المحتوى في الصفحة رقم 7

95-5820 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit). 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disa

ملخص المحتوى في الصفحة رقم 8

95-5820 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 05/07/09 © COPYRIGHT 2009 METRA ELECTRONICS CORPORATION INST95-5820