ملخص المحتوى في الصفحة رقم 1
Owner’s manual Owner’s manual
VMA5096
VMA7196
5” and 7” WIDE SCREEN COLOR LCD MONITOR
VMA5096/VMA7196 1
VMA5096_VMA7196_OwnersManual_rev.pmd.p65 1 11/23/05, 2:52 PM
ملخص المحتوى في الصفحة رقم 2
English Thank you for purchasing this Clarion product. • Please read this owner’s manual in its entirety before operating this equipment. • After reading this manual, keep it handy, such as in your glove compartment. FCC Approval This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment g
ملخص المحتوى في الصفحة رقم 3
Contents 1. FEATURES .........................................................................................................................4 2. PRECAUTIONS ..................................................................................................................5 Installation ...........................................................................................................................5 Please Note ...........................................................................
ملخص المحتوى في الصفحة رقم 4
English 1. FEATURES The Clarion 5-inch VMA5096 and 7-inch VMA7196 are high-performance video monitors designed specifically for the mobile environment. Intended for use with other Clarion multimedia products, the monitors can be integrated with many other products as part of a complete mobile video solution. Two video inputs support simultaneous connection to both dedicated video source units and optional audio/video components, such as camcorders or videogames. • Infrared remote control receiv
ملخص المحتوى في الصفحة رقم 5
2. PRECAUTIONS • Do not operate your monitor in ways other than those described in this manual. • Do not play a multimedia system when the car’s engine is turned off. Doing so runs down the car’s battery. • Do not disassemble or modify the monitor. • Keep moisture away from the monitor. Water and humidity may damage internal circuitry. • Do not let the monitor become overheated. If the temperature in the vehicle is high or the monitor has been exposed to direct sunlight, cool the monitor (such a
ملخص المحتوى في الصفحة رقم 6
English 3. CONTROLS Transmit infrared signals to the 2 ch. IR headphones (hidden behind plastic) Turns power Decreases Increases IR (infrared) receiver for on and off or selects or selects Clarion remote control adjustment adjust- (hidden behind plastic) settings ment Selects the viewing settings Selects the Video 1/ Video2 mode source Accesses the display adjustment menus. Each time you press this button the unit steps to the next setting option and displays the current setting. Wireless headph
ملخص المحتوى في الصفحة رقم 7
Configuration 1 Configuration 2 Monitor Monitor Monitor Monitor IR CH A IR CH A IR CH A IR CH B Video source Video source Video source You don’t need to select the IR channel if you have only one monitor or two monitors and only one video source (Configuration 1—both monitors play the same video or game). 4. OPERATIONS Your monitor is a component of a full audio/video system that may include a VCR, DVD player, game player, camcorder or other video source unit. Note If you have any questions abo
ملخص المحتوى في الصفحة رقم 8
English Playing a video or game Your monitor is preset at the factory to turn on automatically when you start your car’s ignition. The monitor remains dark until it detects a video signal. 1. Insert the media (tape, cartridge, game or disc) into the video source. 2. Turn on the headphones. If this is the first time you’ve used the unit, make sure your headphones have fresh batteries installed. Note Your headphones must be in view of the monitor for the infrared transmis- sion to work. 3. Press p
ملخص المحتوى في الصفحة رقم 9
2. Press MENU again until you reach the option you wish to adjust. The monitor displays the adjustment bar. Example of an adjustment bar TINT adjusts the overall color of the monitor. COLOR adjust the way each color displays. BRIGHT adjusts the monitor’s brightness. CONTRAST adjusts the differences between light and dark areas. 3. Press the right end of the picture controls button to increase the adjustment. Press the left end of the picture controls button to decrease the adjustment
ملخص المحتوى في الصفحة رقم 10
English Changing the video region mode (NTSC/PAL) 1. Press MENU several times to locate the VIDEOSYS option. 2. Press or to alternate between NTSC and PAL. Disabling automatic power on Your monitor is preset at the factory to switch on when you turn on your vehicle’s ignition. You can set it up to remain off until you press the power button on the monitor. 1. Press MENU several times until you reach the AUTOPOWER option. 2. Press or to turn automatic power ON and OFF. Retur
ملخص المحتوى في الصفحة رقم 11
Cleaning the LCD panel Use a soft, dry cloth to gently wipe off dust. The LCD panel surface can be easily scratched. Do not rub it with any abrasive object. Servicing the monitor In the event that trouble arises, never open the case or disassemble the unit. The internal parts are not serviceable by the user. Opening any components will void the warranty. CAUTION! Changes or modifications to this product not approved by the manufacturer will void the warranty and will violate FCC ap- proval. 5.
ملخص المحتوى في الصفحة رقم 12
English Before starting Disconnect the ground (-) terminal on the vehicle’s battery. WARNING! To prevent short circuits during installation, be sure to disconnect the battery. Precautions • This unit is exclusively for vehicles with a negative ground, 12V power supply. • Do not open the case. There are no user-serviceable parts inside. If you require assistance, consult your Clarion dealer or an authorized Clarion service center. • Use a soft, dry cloth to clean the screen. Never use a rough clo
ملخص المحتوى في الصفحة رقم 13
Flush mounting in the headrest You may use the included trim bezel to flush-mount the monitor. 1. Ensure that you will have sufficient clearance for the monitor and its rear-located wiring harness. 2. Cut the opening. 3. Route the DIN-connector end of the wiring harness into the opening from the rear out the front. 4. Insert the trim bezel and route the wiring harness through the opening in the rear. 5. Firmly attach the bezel to the mounting surface and/or to the interior of the mounting surfac
ملخص المحتوى في الصفحة رقم 14
English 7. Gently insert the monitor into the bezel. Press only on the edges of the monitor, not on the screen. You should hear a few soft clicks as the monitor locks into place. CAUTION! NEVER press on the surface of the screen! Gently press on the edges of the monitor case. If you find that you cannot in- sert the monitor without excessive force, you may need to check your wire harness position for interference with the insertion process. You may also need to make the opening slightly large
ملخص المحتوى في الصفحة رقم 15
Wiring the monitor Precautions • Disconnect the negative battery terminal before making any wiring connections. • Be particularly careful where you route wires. Keep them away from the engine, exhaust system, etc. Heat may damage wires. • If the fuse should blow, make sure all connections are correct and no wires are damaged before replacing the fuse. Always use fuses that are the same amperage value as the original. When replacing a fuse, never let the battery side touch any metal part or any o
ملخص المحتوى في الصفحة رقم 16
English Monitor connections CAUTION! Some non-Clarion automotive DVD and VCP source units use a similar connector for an external IR receiver, but use different pin polarity than the Clarion uses. Connecting non-Clarion source equip- ment to this connector could cause equipment damage not covered by the warranty! IR connector polarity +5V ACC Ground IR Data Line Connections diagram R W Y R W or 1 Audio L 6 12V GND 2 IR GND 7IR Y 3 Audio R 8 12V 4 Video GND 9 GND Y - Video RCA Input 5 Video W -
ملخص المحتوى في الصفحة رقم 17
7. Troubleshooting The monitor does not turn on A fuse may be blown. Replace the external fuse with a fuse of the same value. The power wires may not be connected. Check the wiring connections and retest. No picture. Press INPUT to make sure the proper input is selected. If there is still no picture, press MENU. If the menu appears, check the source unit and video connections. If no menu appears, check all fuses and power connections to the monitor and the associated equipment. Note: o o The mo
ملخص المحتوى في الصفحة رقم 18
8. Specifications Note The technical data and the design of the equipment may change without prior notice for the sake of technical improvements. VMA5096 General Specifications Power requirement: 12V DC (9V-16V) Power consumpaion: 6.5 watts, power on 0.6 amps (600mA) Weight: 300 g Dimensions (w x h x d): 138 x 106 x 26.5 mm Included parts: LCD monitor 1 - 16P Main cable 1 - Mounting bracket Monitor release tool VMA5096 Monitor Specifications Display type: Color TFT Active Matrix LCD Screen size:
ملخص المحتوى في الصفحة رقم 19
9. LIMITED WARRANTY INFORMATION For USA and Canada only Except as noted, Clarion products purchased from an authorized Clarion dealer are warranted against all defects in materials and workmanship for a period of one (1) year from date of original purchase. The following Clarion products noted below ** are warranted against all defects in materials and workmanship for a two (2) year perod from the date of original purchase when purchased from AND installed by an authorized Clarion dealer. ** DRZ
ملخص المحتوى في الصفحة رقم 20
Clarion Corporation of America C All Rights Reserved. Copyright 2006: Clarion Corp. of America Printed in China 20 VMA5096/VMA7196 VMA5096_VMA7196_OwnersManual_rev.pmd.p65 20 11/23/05, 2:54 PM
