ملخص المحتوى في الصفحة رقم 1
Pub. 988-0143-711
www.eaglesonar.com
FishMark 480 and
SeaFinder 480DF
Fish-finding & Depth Sounding Sonars
Installation and Operation
Instructions
ملخص المحتوى في الصفحة رقم 2
Copyright © 2003 - Eagle Electronics All rights reserved. ® Eagle is a registered trademark of Eagle Electronics Marine-Tex is a trademark of Illinois Tool Works Inc. Eagle Electronics may find it necessary to change or end our policies, regulations, and special offers at any time. We reserve the right to do so without notice. All features and specifications subject to change without notice. All screens in this manual are simulated. On the cover: SeaFinder 480DF shown. Other models covered in t
ملخص المحتوى في الصفحة رقم 3
Table of Contents Sec. 1: Read Me First! ............................................................... 1 Capabilities and Specifications .................................................... 2 How Sonar Works ......................................................................... 4 How to Use this Manual: Typographical Conventions................ 4 Sec. 2: Installation & Accessories .......................................... 7 Preparations......................................................
ملخص المحتوى في الصفحة رقم 4
Depth Alarms .......................................................................... 46 Zone Alarm.............................................................................. 47 Fish Alarm............................................................................... 48 Brightness ................................................................................... 48 Calibrate Speed........................................................................... 49 Chart Speed.....................
ملخص المحتوى في الصفحة رقم 5
Digital Data/Chart.................................................................. 72 Customizing the Digital Data/Chart Screen...................... 73 Sonar Simulator.......................................................................... 74 Stop Chart................................................................................... 74 Surface Clarity............................................................................ 75 Units of Measure............................................
ملخص المحتوى في الصفحة رقم 6
Notes iv
ملخص المحتوى في الصفحة رقم 7
Section 1: Read Me First! How this manual can get you out on the water, fast! Welcome to the exciting world of digital sonar! We know you're anxious to begin finding fish, but we have a favor to ask. Before you grab your unit and begin installing it, please give us a moment or two to explain how our manual can help you get the best performance from your compact, wide-screen, fish finder. First, we want to thank you for buying anEagle sonar. Whether you're a first time user or a professional fish
ملخص المحتوى في الصفحة رقم 8
After you've gained some experience with your sonar, you'll want to check out Section 4, which discusses more advanced Sonar Options and Other Features. When you come to a sonar menu command on the unit's screen, you can look it up in the manual by skimming over the table of contents, just flipping through Section 3 or scanning through the sonar options in Section 4. If you're having difficulty with your sonar, you can find an answer to the most common problems in Section 5, Sonar Troubleshootin
ملخص المحتوى في الصفحة رقم 9
Back-up memory: .......... Built-in memory stores sonar records for decades. Languages:...................... 10; menu languages selectable by user. Sonar Frequency:...................... 50/200 kHz for SeaFinder 480DF; 200 kHz for FishMark 480. Transducers: .................. A dual-frequency Skimmer transducer with built-in temperature sensor is packed with the SeaFinder 480DF. It has 35°/12° cone angles. A single-frequency Skimmer transducer with built-in temperature sensor is packed with t
ملخص المحتوى في الصفحة رقم 10
Speed/distance log: ....... Optional (requires optional speed sensor). NOTICE! The storage temperature range for your unit is from -4 degrees to +167 degrees Fahrenheit (-20 degrees to +75 degrees Celsius). Extended storage in temperatures higher or lower than specified will damage the liquid crystal display in your unit. This type of damage is not covered by the warranty. For more information, contact the factory's Customer Service Department; phone numbers are listed on the last page. How Sona
ملخص المحتوى في الصفحة رقم 11
menu command to use by finding the boldface command text. The following paragraphs explain how to interpret the text formatting for those commands and other instructions: Arrow Keys The arrow keys control a horizontal line depth cursor on the sonar screen. The arrow keys also help you move around the menus so you can execute different commands. They are represented by symbols like these, which denote the down arrow key, the up arrow, the left arrow and the right arrow: ↓ ↑ ← →. Keyboard The othe
ملخص المحتوى في الصفحة رقم 12
Translated into complete English, step 1 above would mean: "Start on the Sonar Page. Press the Menu key then repeatedly press (or press and hold) the down arrow key to scroll down the menu and select (highlight) the Sonar Features menu command. Then press the Enter key." Step 2 would mean: "Press the right arrow key (for dual-frequency units) or press the right arrow key followed by the down arrow key (for single-frequency units) to select (highlight) the Fish ID symbols command. Next, press the
ملخص المحتوى في الصفحة رقم 13
Section 2: Installation & Accessories Preparations You can install the sonar system in some other order if you prefer, but we recommend this installation sequence: Caution: You should read over this entire installation section before drilling any holes in your vessel! 1. Determine the approximate location for the sonar unit, so you can plan how and where to route the cables for the transducer and power. This will help you make sure you have enough cable length for the desired configuration. 2. D
ملخص المحتوى في الصفحة رقم 14
These are all "kick-up" mounting brackets. They help prevent damage if the transducer strikes an object while the boat is moving. If the transducer does "kick-up," the bracket can easily be pushed back into place without tools. Read these instructions carefully before attempting the installation. Determine which of the mounting positions is right for your boat. Use extreme care if mounting the transducer inside the hull, because once it is epoxied into position, the transducer usually cannot be
ملخص المحتوى في الصفحة رقم 15
then the chosen location must be in the water at all times. If the transducer is not placed in a smooth flow of water, interference caused by bubbles and turbulence will show on the sonar's display in the form of random lines or dots whenever the boat is moving. NOTE: Some aluminum boats with strakes or ribs on the outside of the hull create large amounts of turbulence at high speed. These boats typically have large outboard motors capable of propelling the boat at speeds faster than 35 mph. Typ
ملخص المحتوى في الصفحة رقم 16
How low should you go? For most situations, you should install your Skimmer transducer so that its centerline is level with the bottom of the boat hull. This will usually give you the best combination of smooth water flow and protection from bangs and bumps. Transom Transducer centerline Hull bottom Align transducer centerline with hull bottom. However, there are times when you may need to adjust the transducer slightly higher or lower. (The slots in the mounting brackets allow you to loosen the
ملخص المحتوى في الصفحة رقم 17
However, the shoot-thru-hull installation does have its drawbacks. First, some loss of sensitivity does occur, even on the best hulls. This varies from hull to hull, even from different installations on the same hull. This is caused by differences in hull lay-up and construction. Second, the transducer angle cannot be adjusted for the best fish arches. This can be a problem on some hulls that sit with the bow high when at rest or at slow trolling speeds. Follow the procedure listed in the shoot-
ملخص المحتوى في الصفحة رقم 18
B. Two-piece bracket: Locate the four plastic ratchets in the transducer's hardware package. Press two ratchets into the sides of the plastic bracket and two on either side of the transducer as shown in the following illustrations. Notice there are letters molded into each ratchet. Place the ratchets into the bracket with the letter "A" aligned with the alignment mark molded into the bracket. Place the ratchets onto the transducer with the letter "A" aligned with the 12 o'clock position on the t
ملخص المحتوى في الصفحة رقم 19
2. Aligning the transducer on the transom. A. One-piece bracket: Slide the transducer between the two ratchets. Temporarily slide the bolt though the transducer assembly and hold it against the transom. Looking at the transducer from the side, check to see if it will adjust so that its face is parallel to the ground. If it does, then the "A" position is correct for your hull. If the transducer's face isn't parallel with the ground, remove the transducer and ratchets from the bracket. Place the r
ملخص المحتوى في الصفحة رقم 20
bracket holes with the letter "B" aligned with the bracket alignment mark. Place them on the transducer aligned with the 12 o'clock position on the transducer stem. Reassemble the transducer and bracket and place them against the transom. Again, check to see if you can move the transducer so it's parallel with the ground. If you can, then go to step 3B. If it doesn't, repeat step 2B, but use a different alignment letter until you can place the transducer on the transom correctly. Lock washer Bol
