ملخص المحتوى في الصفحة رقم 1
Model APS 996a
Installation Manual
SELECTABLE FEATURES
Note : The method of manual override can either be selected to operate from the valet switch or operate as custom code. Be
certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.
RF Programmable Features :
Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps Default
1st DoorL/UL 1 Sec. 3.5 Sec. 1 Sec L, Dbl. U/L 1 Sec.
2nd Accy Lock Auto Lock On Auto Lock Off Auto Lock Off
3rd Accy
ملخص المحتوى في الصفحة رقم 2
THIS PAGE INTENTIONALLY LEFT BLANK 128-6773 2 of 28
ملخص المحتوى في الصفحة رقم 3
Eighth Press and release the valet switch 1 chirp = siren and horn output Press transmitter Lock button to change 2 chirps = siren output only Press transmitter lock button to change 3 chirps = horn output only or Ninth Press and release the valet switch 2 chirps = horn chirp output 16mS Press transmitter Lock button to change 3 chirps = horn chirp output 30mS Press transmitter Lock button to change 1 chirp = horn chirp output 10 mS or Tenth Press and release the valet switch 2 chirps = valet sw
ملخص المحتوى في الصفحة رقم 4
hood switch is required for the safety shut down of the remote start unit. If the vehicle is being worked on, this hood switch prevents the remote start activation even if the RF command to start is issued. This switch must be installed in all applications. Failure to do so may result in personal injury or property damage. Mount the switches in the hood and trunk locations away from water drain paths. If necessary, the included brackets may be used to move the switch away from rain gutters
ملخص المحتوى في الصفحة رقم 5
SHOCK SENSOR: Select a centrally located, solid mounting surface for the shock sensor that will allow consistent opera- tion from all areas of the vehicle. The selected location must be within 18" of the control module to allow routing and connecting of the 4 pin harness. Secure the shock sensor to the chosen location using two #8 self tapping sheet metal screws. The sensor can also be secured to an existing dash brace using cable tie straps. Whichever mounting method is used be sure to all
ملخص المحتوى في الصفحة رقم 6
YELLOW Wire: Starter Output Careful consideration for the connection of this wire must be made to prevent the vehicle from starting while in gear. Understanding the difference between a mechanical and an electrical Neutral Start Switch will allow you to properly identify the circuit and select the correct installa- tion method. In addition you will realize why the connection of the safety wire is required for all mechanical switch configurations. Failure to make this connection properly c
ملخص المحتوى في الصفحة رقم 7
WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness White w/ Red Trace Wire: Parking Light Flasher Feed This wire is the common contact of the on board parking light flasher relay. If the vehicle you are working on has +12 volt switched parking lights, connect this wire to a fused + 12 volt source. (Max. 15 Amps) NOTE: If the vehicle's parking lights are ground switched, connect this wire to chassis ground. White Wire: Parking Light Flasher Output This wire is the normally open contac
ملخص المحتوى في الصفحة رقم 8
BLACK White w/ Black Trace Wire: (+) Siren Output This is the positive siren feed wire. Route this wire through a grommet in the firewall to the siren location. Connect the White w/ Black Trace wire to the Red wire of the Siren. Secure the Black wire of the Siren to a known chassis ground or solid clean metal surface. Siren Wiring Detail SIREN TO WHITE w/BLACK WIRE OF MODULE l l (-) TO VEHICLE'S CHASSIS GROUND Purple Wire: (+) Door Trigger Input If the vehicle's door courtesy light switches +
ملخص المحتوى في الصفحة رقم 9
Light Blue Wire: Ignition 3 Output This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of the applications described below, a relay will be required. The Light Blue wire can be used to accommodate the following situations: A. Shock Sensor By Pass: If there is a Non Plug in Shock Sensor used with the alarm system and it is not
ملخص المحتوى في الصفحة رقم 10
Green w/ White trace Wire: Entry Illumination Ground Output This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm the alarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is triggered. This wire should be connected to an external relay and wired to the vehicles interior entry lighting whenever the optional Interior Illumination circuit is desired. See below for relay wiring details. Entry Illumination Detail Grey
ملخص المحتوى في الصفحة رقم 11
Orange Wire: Ground When Armed Output This wire provides a 300 mA ground output when the alarm circuit is armed to control the starter inhibit relay. Connect the Orange wire to terminal #86 (orange wire) of the relay provided. Connect terminal #85 (red wire) of the relay to an ignition wire in the vehicle that is +12 volts when the ignition switch is turned to the on and start positions and off when the key is off. Locate and cut the low current start solenoid wire found at the vehicles igni
ملخص المحتوى في الصفحة رقم 12
Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Be certain to remove any paint or grease and secure this wire with a self tapping screw and ring terminal. Chassis Ground Connection Detail Green w/ Orange Trace Wire: Tachometer Input Signal This wire will continually monitor the engine's tach rate while the unit is under power of the Remote Start module. This wire will be routed to the vehicle ECM tach inp
ملخص المحتوى في الصفحة رقم 13
Dark Blue Wire: Delayed 300mA Pulsed Channel 3 Output The Dark Blue wire supplies a 300mA ground pulsed output whenever channel three of the receiver is accessed. Pressing the pre-programmed transmitter button for three seconds will access channel two. This is a low current output and must be connected to a relay to supply power to the trunk release or the circuit you wish to control. Connect the Dark Blue wire to terminal # 86 of a VF45F11 P&B relay or equivalent. Connect terminal # 85 o
ملخص المحتوى في الصفحة رقم 14
NOTE : This is a normally opened starter cut arrangement, and when power is removed from the security system, the starter disable feature will remain operational, and the vehicle will not start. Audiovox does not recommend using the Orange w/ White trace wire to interrupt anything but the starting circuit of the vehicle. Lt Green Wire: (-) Instant Trigger Zone 1 This is a instant on ground trigger input intended for the connection of optional triggering devices. The ground trigger output wire
ملخص المحتوى في الصفحة رقم 15
Black w/ Yellow Trace Wire: Ground Output During Start (Crank) The Black w/ Yellow Trace wire will provide a 300 mA ground output while the starter output of the remote start unit is active. This output can be used to activate the Crank Low/Bulb Test wire found in some GM vehicles. This wire is also referred to as the ECM wake up wire in some vehicles. NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement is more than 300 mA. 2 Pin Transpo
ملخص المحتوى في الصفحة رقم 16
3 Wire Ground Switched Door Lock Circuits: In this application, the Red wire of the door lock harness provides a ground pulse during the arming sequence, or pulsed ground lock output. Connect the Red wire to the low current ground signal wire from the factory door lock switch to the factory door lock relay. The Green wire of the door lock harness provides a ground pulse during the disarming sequence, or pulsed ground unlock output. Connect the Green wire to the low current ground signal wire f
ملخص المحتوى في الصفحة رقم 17
The Red/Black wire provides a pulse ground output when the unlock button of the transmitter is pressed a second time after disarming. Connect the Red/Black wire to the wire that provides a low current ground signal from the factory door unlock switch to the factory door unlock control relay. 3 Wire Positive Switched 2 Step Door Locks: The green wire provides a positive pulse during arming or the pulsed + 12 volt lock output. Connect the green wire to the wire that provides a low current positiv
ملخص المحتوى في الصفحة رقم 18
NOTE: Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, or for convenience, the AS 9159 Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and or the Audiovox fax back service for information on your particular vehicle for properly connecting to these types of circuits. ALARM SELECTABLE FEATURES NOTE: The Alar
ملخص المحتوى في الصفحة رقم 19
START PROGRAM: The Remote Start unit has the ability to start the vehicle automatically at timed intervals. This feature is useful in extremely cold climates where starting the engine is the only means to keep the battery charged and fluids warm. The operator has the option to have the unit start every 2 or 4 hours for a maximum of 48 hours. Factory pre-set is to start at 4 hour intervals. To select 2 or 4 hour automatic start timer: 1. Start with the Enable switch (Red Handle) in the "On"
ملخص المحتوى في الصفحة رقم 20
times in succession. The parking lights will flash, and the siren will chirp 3 times confirming that selected feature 3 can be changed. . Use the start button on the transmitter to change the selection of the programmable feature. If you are 7 not sure what the setting for any feature is, press the start button one time, the parking lights will flash once or twice indicating the features setting. NOTE: Once you've entered the program mode DO NOT allow more than 15 seconds to pass between step
