Metra Electronics 99-9107B دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

INSTALLATION INSTRUCTIONS FOR PART 99-9107B
APPLICA TIONS
Audi A4 / S4
2002-2008
(With Symphony Radio)
99-9107B
KIT FEATURES
• DIN Head Unit Provision with Pocket
• ISO DIN Head Unit Provision with Pocket
• Double DIN Head Unit Provision
• Painted Matte Black to Match Factory
KIT COMPONENTS
• A) Radio Housing • B) Pocket • C) Trim Plate • D) ISO Brackets • E) Double DIN Trim Plate
• F) Double DIN Brackets
A B
C D
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:

ملخص المحتوى في الصفحة رقم 2

99-9107B TABLE OF CONTENTS Dash Disassembly - Audi A4 / S4 2002-2008 w/Symphony Radio . . . . . . . . . . . . . . 1 Kit Assembly - DIN Head Unit Provision with Pocket . . . . . . . . . . . . . . . . . . . . . 2 - ISO DIN Head Unit Provision with Pocket . . . . . . . . . . . . . . . . . . 3 - Double DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 KNOWLEDGE IS POWER Enhance your

ملخص المحتوى في الصفحة رقم 3

DASH DISASSEMBLY 99-9107B AUDI A4 / S4 2002-2008 W/SYMPHONY RADIO 1 Disconnect the negative battery A terminal to prevent an accidental short circuit. 2 Insert Metra’s 86-9001 into the slots in the factory head unit and pull the unit out. (Figure A) CD LOAD AS FM MENU AM TONE 3 Disconnect the wiring. SAT RDS TAPE SCAN 1

ملخص المحتوى في الصفحة رقم 4

KIT ASSEMBLY 99-9107B DIN HEAD UNIT PROVISION WITH POCKET A 1 Snap the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 2 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 3 Snap radio assembly into factory B radio opening. 4 Slide the aftermarket radio into the cage and secure. (Figure B) 5 Snap the po

ملخص المحتوى في الصفحة رقم 5

KIT ASSEMBLY 99-9107B ISO DIN HEAD UNIT PROVISION 1 Mount the ISO Brackets to the A head unit with the screws sup- plied with the unit. (Figure A) 2 Slide the head unit into the radio opening until the slide clips engage. (Figure B) 3 Snap the ISO Trim Plate into the Radio Housing. (Figure B) 4 Snap the pocket into the Radio B Housing. (Figure C) 5 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter from Metra or AXXESS. Re-con- nect the negative ba

ملخص المحتوى في الصفحة رقم 6

KIT ASSEMBLY 99-9107B DOUBLE DIN HEAD UNIT PROVISION 1 Cut and remove center divider A from radio housing. (Figure A) Snap the DDIN brackets to the 2 inside edge of the radio housing. (Figure B) Slide the DDIN radio unit into the 3 DDIN bracket/radio housing assembly and secure the unit to the kit using the screws supplied with the head unit. (Figure C) 4 Snap the DDIN trim-plate onto the B housing/radio assembly. (Figure C) Locate the factory wiring harness 5 in the dash. Metra recommend

ملخص المحتوى في الصفحة رقم 7

99-9107B NOTES 5

ملخص المحتوى في الصفحة رقم 8

99-9107B INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 10/26/09 © COPYRIGHT 2004-09 METRA ELECTRONICS CORPORATION INST99-9107B