Metra Electronics 99-8903B دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

INSTALLATION INSTRUCTIONS FOR PART 99-8903B
APPLICATIONS
SUBARU
LEGACY & OUTBACK
2010-11
(FOR NON-NAVIGATION RADIOS ONLY)
99-8903B
KIT FEATURES
• DIN radio provision with pocket
• ISO radio provision with pocket
• Painted scratch resistant matte black
KIT COMPONENTS
A) Radio Housing B) ISO Brackets C) Trim plate
B
C
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• 70-8901 Subaru Harness 1990-Up
A
• 70-7552 Nissan Harness 2007-Up
Antenna Adapter:
• 40-SB10 Subaru Antenna Adap

ملخص المحتوى في الصفحة رقم 2

99-8903B TABLE OF CONTENTS Dash Disassembly - 2010-11 Subaru Legacy . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 1 - 2010-11 Subaru Outback . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 - ISO DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 *Note: Refer also to the instructions included with t

ملخص المحتوى في الصفحة رقم 3

99-8903B DASH DISASSEMBLY 2010-11 SUBARU LEGACY / OUTBACK A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove the radio trim panel including the a/c vents. (Figure A) 3 Remove (4) Phillips screws securing the factory radio. 1

ملخص المحتوى في الصفحة رقم 4

99-8903B KIT ASSEMBLY 2010-11 SUBARU LEGACY / OUTBACK DIN HEAD UNIT PROVISION 1 Locate the factory wiring harness in the dash. Metra recommends using A the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure A) 3 Slide the aftermarket head unit into the cage and secure. (Figure B) B 4 Reassemble dash in reverse order

ملخص المحتوى في الصفحة رقم 5

99-8903B KIT ASSEMBLY 2010-11 SUBARU LEGACY / OUTBACK ISO DIN HEAD UNIT PROVISION 1 Locate the factory wiring harness in the dash. Metra recommends using A the proper mating adapter from Metra or AXXESS. Re-connect the negative battery terminal and test the unit for proper operation. 2 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure A) 3 Slide the head unit into the radio opening until the side clips engage. (Figure B) B 4 Snap the Trim plate into the

ملخص المحتوى في الصفحة رقم 6

99-8903B NOTES

ملخص المحتوى في الصفحة رقم 7

99-8903B NOTES

ملخص المحتوى في الصفحة رقم 8

99-8903B INSTRUCTIONS 306 INSTRUCTIONS METRA. THE WORLD’S BEST KITS.™ 1-800-221-0932 www .metraonline.com REV. 11/18/10 © COPYRIGHT 2003-2010 METRA ELECTRONICS CORPORATION INST99-8903B