ملخص المحتوى في الصفحة رقم 1
INSTALLATION INSTRUCTIONS FOR PART 99-8205
APPLICATIONS
Toyota Matrix 2003-2008
Pontiac Vibe 2003-2008
99-8205
KIT FEATURES
• DIN head unit provision
• ISO DIN head unit provision
• DDIN head unit provision
- Excluding 2005-2008 Matrix
• Stacked ISO DIN head unit provision
- Excluding 2005-2008 Matrix
KIT COMPONENTS
A) DDIN Faceplate (excluding 2005-2008 matrix) • B) ISO DIN Faceplate (excluding 2005-2008 matrix)
• C) ISO DIN Faceplate 2005-2008 Matrix D) Pocket • E) Mounting Bracket
ملخص المحتوى في الصفحة رقم 2
99-8205 TABLE OF CONTENTS Dash Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1,2 Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 4, 5, 6, 7,8 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com
ملخص المحتوى في الصفحة رقم 3
TUNE AM FM1 FM2 DISK SCAN SEEK TRACK DASH DISASSEMBLY 99-8205 TOYOTA MATRIX 2003-2008 PONTIAC VIBE 2003-2008 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip the bottom edge of the radio trim panel then lift up and out to remove. (Figure A) 3 Remove (4) 10 MM bolts securing the factory radio. (Figure B) B 1
ملخص المحتوى في الصفحة رقم 4
KIT ASSEMBLY 99-8205 DIN HEAD UNIT PROVISION A 1 Choose the correct faceplate for your application. The 2005-2008 Matrix #8x3/8” Screw faceplate is smaller than the other supplied faceplate. 2 Attach the pocket to the back of the ISO/DIN Faceplate (by holding the #8x3/8” Screw faceplate upside down and inserting the right edge of the pocket into place then pushing the rest of the pocket onto the lip) and mount with B (2) #8X3/8” Phillips screws. (Figure A) NOTE: For the 2005-2008 Matrix, break
ملخص المحتوى في الصفحة رقم 5
KIT ASSEMBLY 99-8205 DIN HEAD UNIT PROVISION D Mount the rear support to the back 4 #6x1/4” Screws Two #8x3/8” Screws of the pocket with (2) #8X3/8” Phillips screws. (Figure D) 5 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure E) 6 Slide the aftermarket head unit into the cage and secure. (Figure F) E #6x1/4” Screws F 3
ملخص المحتوى في الصفحة رقم 6
99-8205 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION A 1 Choose the correct faceplate for your #8x3/8” Screw application. The 2005-2008 Matrix faceplate is smaller than the other supplied faceplate. #8x3/8” Screw 2 Attach the the pocket to the back of the ISO/DIN Faceplate (by holding the face- plate upside down and inserting the right edge of the pocket into place then push- B ing the rest of the pocket onto the lip) and mount with (2) #8X3/8” Phillips screws. (Figure A) NOTE: For the 2005-2008 M
ملخص المحتوى في الصفحة رقم 7
99-8205 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION D 4 Mount the rear support to the back #6x1/4” Screws Two #8x3/8” Screws of the pocket with (2) #8x3/8” Phillips screws. (Figure D) 5 Mount the ISO Brackets to the head unit with the screws supplied with the unit. (Figure E) 6 Slide the the head unit into the radio opening until the side clips engage. E (Figure F) #6x1/4” Screws 7 Snap the Trim plate into the Radio Housing. (Figure F) F 5
ملخص المحتوى في الصفحة رقم 8
99-8205 KIT ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION A NOTE: 2005-2008 Matrix not applicable. 1 Cut and remove the bottom portion (Displayed) of the mounting brack- ets. (Figure A) 2 Cut and remove the center bar from the DDIN faceplate. (Figure B) B 3 Attach the ISO spacers to the mounting brackets by inserting the (4) bosses on each spacer into the (4) holes in each bracket. (Figure C) 4 Attach the mounting brackets to the DDIN head unit with the screws sup- plied with the unit. (Figure D) C
ملخص المحتوى في الصفحة رقم 9
99-8205 KIT ASSEMBLY STACKED ISO DIN HEAD UNIT PROVISION A NOTE: 2005-2008 Matrix not applicable. 1 Cut and remove the bottom portion (Displayed) of the mounting brack- ets. (Figure A) 2 Attach the ISO spacers to the mount- ing brackets by inserting the (4) B bosses on each spacer into the (4) holes in each bracket. (Figure B) 3 Attach the mounting brackets to the DDIN head unit with the screws sup- plied with the unit. (Figure C) 4 Attach the DDIN faceplate over the head unit by snapping the
ملخص المحتوى في الصفحة رقم 10
KIT ASSEMBLY 99-8205 FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 2 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring co
ملخص المحتوى في الصفحة رقم 11
99-8205 NOTES 9
ملخص المحتوى في الصفحة رقم 12
INST998205 1-800-221-0932 www.metraonline.com © COPYRIGHT 2004-08 METRA ELECTRONICS CORPORATION REV. 09/26/08 INST99-8205
