Metra Electronics 99-5819 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

INSTALLATION INSTRUCTIONS FOR PART 99-5819
APPLICATIONS
FORD
F-150 (XL Models Only) 2009-10
99-5819
KIT FEATURES
• DIN Radio Provision With Pocket
• ISO Mount Radio Provision With Pocket
KIT COMPONENTS
• A) Radio Housing • B) Radio Housing Brackets • C) ISO Brackets • D) Trim Plate
C
B
A
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wire harness:
• 70-5520 Ford harness 2003-up
Antenna adapter:
D
• 40-CR10 Chrysler antenna 2002-up
TOOLS REQUIRED:
Cutting Tool • Phillips Screwdrive

ملخص المحتوى في الصفحة رقم 2

99-5819 TABLE OF CONTENTS Dash Disassembly - FORD F-150 (XL Models Only) 2009-10 . . . . . . . . . . . . . . . . . .1 Kit Assembly - DIN Radio Provision With Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - ISO Mount Radio Provision With Pocket. . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 *Note: Refer also to the instructions included with the aftermarket radio.

ملخص المحتوى في الصفحة رقم 3

99-5819 DASH DISASSEMBLY FORD F-150 (XL Models Only) 2009-10 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the switch panel to the right of the cigarette lighter then remove the (1) 9/32” screw exposed. (Figure A) 3 Remove the rubber pad at the top of the radio trim panel then remove the (2) 9/32” screws exposed. (Figure B) 4 Unclip and pull the side panels con- B taining the a/c vents away from the radio trim panel. Note: It is not nec

ملخص المحتوى في الصفحة رقم 4

99-5819 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the top (2) mounting holes off of the radio housing. CUT HERE -TOP LEG ONLY Note: The notch in the housing CUT should be on top. (Figure A) CUT HERE -TOP LEG ONLY 2 Slide the included brackets onto the sides of the radio housings pocket CUT from the back of the housing forward. (Figure B) 3 Slide the DIN cage into the Radio Housing and secure by ben

ملخص المحتوى في الصفحة رقم 5

99-5819 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Cut and remove the top (2) mounting A holes off of the radio housing. Note: The notch in the housing CUT HERE -TOP LEG ONLY should be on top. (Figure A) CUT CUT HERE -TOP LEG ONLY 2 Slide the included brackets onto the sides of the radio housings pocket from the back of the housing CUT forward. (Figure B) 3 Mount the ISO Brackets to the head unit with the screw

ملخص المحتوى في الصفحة رقم 6

99-5819 FINAL ASSEMBLY FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit). 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Position the factory bracket/aftermarket radio

ملخص المحتوى في الصفحة رقم 7

99-5819 NOTES 5

ملخص المحتوى في الصفحة رقم 8

99-5819 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 04/23/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-5819