Metra Electronics 95-8153 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

INSTALLATION INSTRUCTIONS FOR PART 95-8153
APPLICATIONS
LEXUS LS SERIES
1995-2000
NOT FOR USE IN VEHICLES WITH FACTORY
NAVIGATION
95-8153
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Double DIN Radio Housing B) Double DIN Brackets
A
B
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket Set
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2008 METRA ELECTRONICS CORPORATION

ملخص المحتوى في الصفحة رقم 2

95-8153 TABLE OF CONTENTS Dash Disassembly - Lexus LS Series 1995-2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Kit Assembly - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 *Note: Refer also to the instructions included with the aftermarket

ملخص المحتوى في الصفحة رقم 3

95-8153 DASH DISASSEMBLY LEXUS LS SERIES 1995-2000 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Starting at rear of panel surrounding the shifter carefully pry up and out to remove entire panel including ashtray. (Figure A) 3 Using a panel removal tool or small flat blade screwdriver gently pry out on the top of the A/C vent assembly (including clock) and remove. B (Figure B) 4 Remove (4) screws securing the fac- tory radio/climate control assembly. Un

ملخص المحتوى في الصفحة رقم 4

95-8153 KIT ASSEMBLY LEXUS LS SERIES 1995-2000 DOUBLE DIN RADIO STACKED ISO MOUNT UNITS PROVISON Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN Brackets onto the Double DIN Radio Housing. (Figure A) 2 Slide the factory climate controls into the Bracket/Radio Housing assembly aligning the top of the assembly with alignment pins in the bottom of the climate controls and secure using the factory hardware. (Figure B) 3 Slide the Double DIN or s

ملخص المحتوى في الصفحة رقم 5

95-8153 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

ملخص المحتوى في الصفحة رقم 6

95-8153 NOTES 4

ملخص المحتوى في الصفحة رقم 7

95-8153 NOTES 5

ملخص المحتوى في الصفحة رقم 8

95-8153 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 04/29/08 © COPYRIGHT 2008 METRA ELECTRONICS CORPORATION INST95-8153