Metra Electronics 95-7325 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

INSTALLATION INSTRUCTIONS FOR PART 95-7325
APPLICATIONS
Hyundai Santa Fe
2007-10
(excludes 2010 NAV models)
95-7325
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Units Provision
KIT COMPONENTS
A) Double DIN Trim Plate B) Double DIN Brackets
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-7302 - Hyundai Harness 2007-up
• 70-7305 - Hyundai / KiA Harness 2009
Antenna Adapter:
A B
• 40-KI11 - 2009-10 Santa Fe Adapter
TOOLS REQUIRED:
Small Flat Blade Screwdriver • Panel Re

ملخص المحتوى في الصفحة رقم 2

95-7325 TABLE OF CONTENTS Dash Disassembly - Hyundai Santa Fe 2007-10 .. ........ ....... ........ ........ ....... .1 Kit Assembly - Double DIN Radio Provision ..... ........ ........ ....... ..... ... ... 2 - Stacked ISO Units Provision..... ........ ....... ........ ..... ... ...3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions included with the aftermarket radio.

ملخص المحتوى في الصفحة رقم 3

95-7325 DASH DISASSEMBLY HYUNDAI SANTA FE 2007-10 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Remove (1) Phillips screw from the right side of the panel below the steering column then unclip and let right side of panel hang. (Figure A) Unclip and remove the cover above 3 the clock on top of panel surrounding the radio. (Figure B) 4 Unclip and remove the panel extend- B ing across the dash below the a/c control and above the glove box including the ash

ملخص المحتوى في الصفحة رقم 4

95-7325 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN brackets to the outside edge of the Double DIN trim plate. (Figure A) 2 Slide the Double DIN radio into the bracket/trim plate assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure B) Continue to final assembly. B 2

ملخص المحتوى في الصفحة رقم 5

95-7325 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN brackets to the outside edge of the Double DIN trim plate. (Figure A) 2 Slide the stacked ISO units into the bracket/trim plate assembly and secure the units to the assembly using the screws supplied with the units. (Figure B) Continue to final assembly. B 3

ملخص المحتوى في الصفحة رقم 6

95-7325 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

ملخص المحتوى في الصفحة رقم 7

95-7325 NOTES 5

ملخص المحتوى في الصفحة رقم 8

95-7325 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 04/27/10 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST95-7325