ملخص المحتوى في الصفحة رقم 1
INSTRUCTION MANUAL
Digital Eight Channels/Four Channels Video Recorder
EDR810H/810M/
410H/410M
V 1.21
About this manual
Before installing and using this unit, please read this Manual carefully.
Be sure to keep it handy for later reference.
Updated on: Nov. 17th 2005
ملخص المحتوى في الصفحة رقم 2
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communic
ملخص المحتوى في الصفحة رقم 3
This advice complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
ملخص المحتوى في الصفحة رقم 4
Safety Warning WARNING TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This is a
ملخص المحتوى في الصفحة رقم 5
Safety Precautions Safety Precautions ?Refer all work related to the installation of this product to qualified service personnel or system installers. ?Do not block the ventilation opening or slots on the cover. ? Do not drop metallic parts through slots.This could permanently damage the appliance. Turn the power off immediately and contact qualified service personnel for service. ?Do not attempt to disassemble the appliance.To prevent electric shock, do not remove screws or covers. There
ملخص المحتوى في الصفحة رقم 6
Safety Precautions Safety Precautions The lightning flash with an arrowhead symbol, within an Warning: equilateral triangle, is intended to alert the user to the presence Electrostatic-sensitive device. Use proper of uninsulated ” dangerous voltage ” within the product’s enclosure CMOS/MOSFET handing precautions to avoid that may be of sufficient magnitude to constitute a risk of electric electrostatic discharge. shock to persons. Do not place on uneven or unstable work surfaces. The exclamati
ملخص المحتوى في الصفحة رقم 7
Important Safeguards Important Safeguards Read Instruction---All the safety and operating instructions should be read before the unit is operated. Retain Instructions---The safety and operating instructions should be retained for future reference. Heed Warnings— All warnings on the unit and in the operating instructions should be adhered to. Follow Instructions— All operating and use instructions should be followed. Cleaning— Unplug the unit from the outlet before cleaning. Do not use liquid cle
ملخص المحتوى في الصفحة رقم 8
Table of Contents 1. PRODUCT INTRODUCTION …………………………………………………………… .………… 8 1.1 FEATURES ………………………………………………………………… ..………… ..………… . 8 1.2 SPECIFICATIONS…………………………………………………………………………… .……… 9 1.3 FRONT PANEL KEYPADS ………………………………………………………… ..…… .……… 11 1.4 BACK PANEL CONNECTORS …………………………………………………………… .……… 14 1.5 MONITOR DISPLAY ……………………………………………………………………… .……… 17 2. INSTALLATION …………………………………………………………………………… .………… 20 2.1 PACKING LIST ……………………………………………………………………… ...…… .……… 20 2.2 SYSTEM FLOORPLAN ……………
ملخص المحتوى في الصفحة رقم 9
Table of Contents 5. PLAYING BACK…………………………… ..…………………………………………… ..……… ... 62 5.1 NORMAL PLAYBACK……………… .……………………………………………………………… 62 5.2 SEARCH PLAYBACK …………………………………………………… .………………………… 64 6. COPY TO A VIDEO FILE ………………………………………………… .………………………… 66 7. CALL ……………………………………………………………………… ..……… .………………… 68 8. SCREEN DISPLAY SETTING ………………………… ..……………… ..………………………… 70 9. SCREEN DISPLAY MODE ………………………………… .…………… .………………………… 71 10. REMOTE VIEWER …………………………………… ..……………… ..………………………… 72 APPENDIX A: RS232 s
ملخص المحتوى في الصفحة رقم 10
1. PRODUCT INTRODUCTION The Digital Video Recorder is the industry’s first full-featured digital video recorder designed specifically for use in security industry. The Digital Video Recorder incorporates all the benefits of digital video recording, is simple to install, and operates just like a VCR. Highly efficient compression technology and superior resolution of recorded images make the Digital Video Recorder stand out from the competition as the best choice for security surveillance.
ملخص المحتوى في الصفحة رقم 11
1.2 SPECIFICATIONS Video Format NTSC/EIA or PAL/CCIR Video Input 4/8 camera inputs (BNC), 1Vp-p/75ohm 1 BNC video out (1Vp-p/75ohm) for Main Monitor 1 BNC video out (1Vp-p/75ohm) for CALL Monitor Video Output 4 video out (1Vp-p/75ohm) for Looping (4 Channels only) Video Compression MPEG4 720x240, 720x480 or 360x240 for NTSC Recording Resolution 720x288, 720x576 or 360x288 for PAL Full, PIP, 4, 7, 8/9 and 2x2 Zoom for Live Viewing Video Display and Playback 720x240, 720x480 or 36
ملخص المحتوى في الصفحة رقم 12
Title 12-characters title for each camera Ethernet RJ45 connectors for network communication USB for archiving Archive Archive through Wireless transmission (Reserved) RS-232 9-pin female connector for local communication RS-485 for Keyboard connection Audio 2 mono inputs, 2 mono (SPEAKER) outputs Power Rate DC 12V/DC 24V Half size: 320 mm (L) x 215mm (W) x 100mm (H) Dimension Mobile : 320.8mm (L) x 215mm (W) x 109.9mm(H) Weight 4.85 KG Operating o o 0 C ~ +50 C Temperatur
ملخص المحتوى في الصفحة رقم 13
1.3 FRONT PANEL KEYPADS KEY 1 8 Channel Key: Press FULL+Channel Key (CH1~CH8 ) to display video image in the full screen ~ format the picture of the corresponding will fill the whole screen of the monitor display. CH1 / REC: Press this key to start instant recording. 1 CH2 / REV. PLAY: Reverse Play Back. 2 3 CH3 / STOP: Press this key to stop recording and playing back. 4 CH4 / PLAY: Play Back. 5 CH5 / PAUSE: Press this key to pause the playback picture. 6 CH6 / SEARCH: Press this key to
ملخص المحتوى في الصفحة رقم 14
10 MODE: Switch PIP, 4, 7, and 8 displays in Live and Playback modes. 11 ZOOM: Press this key while viewing the full screen image to display a magnified resolution on the monitor. You must be in “Full” screen mode first before zooming. While zooming, all other function keys will be disable until you press “ZOOM” again to exit “ZOOM” mode. 12 SEQ: Press this key to enter the auto sequential switching mode. 13 SELECT: Press this key to select, to assign a camera to a display, to adjust screen d
ملخص المحتوى في الصفحة رقم 15
19 Shuttle and Jog Dial Shuttle: In the Playback mode, turn the Shuttle dial to fast forward/rewind the video. In the Pause mode, turn the Shuttle dial to slow forward/rewind the video. In the Search mode, turn the Shuttle to change pages. Jog Dial: In the Pause mode, turn the Jog dial to forward/rewind the video. In the Menu mode, turn the Jog dial to change settings and values in subentries. 20 USB Slot: Insert a USB to archive an image or video file. 21 HDD LEDs: LEDs for HDD active power
ملخص المحتوى في الصفحة رقم 16
1.4 BACK PANEL CONNECTORS Back panel of 810M Back panel of 810H Back panel of 410M Back panel of 410H POWER Main Power plug: Connect the DC 12~ 24V power source to adapter for AC 100~ 240V. 1 14
ملخص المحتوى في الصفحة رقم 17
AUDIO 2 Audio IN: Audio input for recording, and it can be set to “YES” or “NO” in the RECORD SETUP MENU. Audio OUT: Connect to an audio input of a monitor or other device. MONITOR MAIN MONITOR: This connector is used for the main monitor display, a number of different 3 display modes may be selected for viewing. 4 CALL MONITOR: This connector is used for the call monitor. This monitor can only display a full screen or a quad screen. VIDEO IN 5 For EDR810 Series: VIDEO IN(1~8): The BNC connect
ملخص المحتوى في الصفحة رقم 18
LAN 7 LAN Connector: The RJ-45 LAN connector. RS232 8 RS232 connector: Connect D-Sub 9 pins connector to RS232 ports for remote control. RS485 9 RS485 connector: RJ 45 Connector to Cascade multi Digital Video Recorder. Remote 10 Remote Control: Remote control port provides you an extension wire with an IR receiver instead of the IR receiver on the front panel. Note: The IR receiver extension line (10m) must be purchased separately. Wireless LAN (Reserved) Antenna: Integrated IEEE 802.11b/g wire
ملخص المحتوى في الصفحة رقم 19
1.5 MONITOR DISPLAY The status information of the cameras or machine will show up, and be located at different places on the screen. 1. Channel tag 2. Event sign 3. Select sign 2. Event sign 4. Play status bar 5. Record status bar 1 Channel tag: A channel tag indicates the channel name of the screen. 2 Event sign: Event signals which are small icons with a capital letter and red background show the events on each screen. There are 4 different signals which are : Alarm event. The alarm pla
ملخص المحتوى في الصفحة رقم 20
3 Select sign: You can assign a camera to a display by pressing SELECT key in life mode. Dial Jog to move the select sign to the display you would like to change camera, and then press FULL + channel key to relocate the camera. 4 Play status bar: The play status bar appears in play back mode if you enable a status bar on the screen (Check page 12, item 15th, DISPLAY). Three parts which are play date, play time and play status are shown in the play status bar. Play Date
