ملخص المحتوى في الصفحة رقم 1
INSTALLATION INSTRUCTIONS FOR PART 99-7300
APPLICATIONS
HYUNDAI Tiburon 1997-2002
HYUNDAI Accent 2000-2001
99-7300
KIT FEATURES
• ISO Mount Radio Provision
KIT COMPONENTS
A) Radio Housing 1 • B) Bracket Set 1 • C) (2) #10 x 3/4” Phillips Screws • D) Radio Housing 2
• E) Bracket Set 2 • F) (4) #10 x 3/4” Phillips Pan Headed Screws
A C
B
D
E
F
TOOLS REQUIRED:
Phillips Screwdriver • Panel Removal Tool
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
ملخص المحتوى في الصفحة رقم 2
99-7300 TABLE OF CONTENTS Dash Disassembly - HYUNDAI Tiburon 1997-2002 . . . . . . . . . . . . . . . . . . . . . . . . . .1 - HYUNDAI Accent 2000-2001 . . . . . . . . . . . . . . . . . . . . . . . . . ..2 Kit Assembly - Tiburon ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . .3 - Accent ISO Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 *No
ملخص المحتوى في الصفحة رقم 3
99-7300 DASH DISASSEMBLY HYUNDAI Tiburon 1997-2002 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Remove (4) Phillips screws securing the center console. Pry out on the front edge of the console and unclip the radio trim bezel. Remove (4) Phillips screws securing the factory head unit and disconnect the wiring. (Figure A) Continue to final assembly. 1
ملخص المحتوى في الصفحة رقم 4
99-7300 DASH DISASSEMBLY HYUNDAI Accent 2000-2001 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Open the cupholder and remove (2) Phillips screws exposed. Lower the glove box and detach the vent cable exposed. Reach under the driver's side dash and detach the vent cable exposed. Reach under the driver's side dash and detach (2) vent cables located above the accelerator. Unclip the dash trim bezel and remove. Remove (4) screws securing the fac- tory hea
ملخص المحتوى في الصفحة رقم 5
99-7300 KIT ASSEMBLY HYUNDAI TIBURON ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Snap the ISO Brackets over the mount- A ing tabs on the Radio Housing. (Figure A) 2 Slide the head unit into the Radio Housing, align the holes in the head unit with the holes in the Housing and mount the unit with the screws supplied with the unit. (Figure B) Continue to final assembly. B 3
ملخص المحتوى في الصفحة رقم 6
99-7300 KIT ASSEMBLY HYUNDAI ACCENT ISO MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the ISO Brackets over the mounting tabs on the Radio Housing. (Figure A) 2 Slide the head unit into the Radio Housing, align the holes in the head unit with the holes in the Housing and mount the unit with the screws sup- plied with the unit. (Figure B) Continue to final assembly. B 4
ملخص المحتوى في الصفحة رقم 7
99-7300 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse
ملخص المحتوى في الصفحة رقم 8
99-7300 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 08/24/07 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST99-7300
