ملخص المحتوى في الصفحة رقم 1
TOSHIBA AMERICA INFORMATION SYSTEMS
STORAGE DEVICE DIVISION
IRVINE, CALIFORNIA
SD-R5372
DVD REWRITEABLE DRIVE
USER MANUAL
ملخص المحتوى في الصفحة رقم 2
CONTENTS Introduction..............................................................................1 Setup ........................................................................................3 Using the DVD Rewriteable Drive...........................................7 Troubleshooting.....................................................................10 Specifications ........................................................................11 Drive Connectors.........................
ملخص المحتوى في الصفحة رقم 3
INTRODUCTION – SD-R5372 General Features Reads and records digital data on DVD-R/-RW, DVD+R/+RW, DVD+R DL, CD-R/-RW, HS CD-RW and US CD-RW discs. Read Write DVD-R 12X 16X* Capable DVD+R 12X 16X DVD-RW 6X 6X* Capable DVD+RW 6X 8X* Capable DVD+R DL 8X 5X DVD-ROM 16X n/a DVD-RAM 2X n/a CD-ROM 48X n/a CD-R 48X 48X CD-RW 24X 4X CD-DA 40X n/a HS CD-RW - 10X US CD-RW - 24X * Free firmware upgrade available on Toshiba SDD Website that will boost DVD-R write speed from 1
ملخص المحتوى في الصفحة رقم 4
Types of Disc Formats Supported - Read DVD: DVD-ROM, DVD-R/RW, DVD+R, DVD+R DL, DVD+RW, DVD-RAM CD: CD-DA, CD+G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video-CD), Multi-session (Photo-CD, CD-EXTRA, CD-R, CD-RW, Portfolio) Front Panel Figure 1.SD-R5372 DVD Writeable Drive Front Panel Loading Load disc using tray. Tray Busy Light The LED lights green or amber when the drive is operating (LED is amber when drive is LED writing.) Ejec
ملخص المحتوى في الصفحة رقم 5
SETUP – SD-R5372 The following steps must be performed to properly install your drive: • Set Drive Jumper Settings • Connect Audio Cable • Attach IDE BUS Cable • Attach Power Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pins located on the rear of the DVD Rewriteable drive. By placing a jumper on the pins, you can select the following functions: CS Drive is configured using host interface signal CSEL SL Configures drive as Slave MA
ملخص المحتوى في الصفحة رقم 6
Placing DVD Rewriteable Drive inside your Computer Now that you have set the jumpers, you are ready to install your DVD Rewriteable drive inside your computer. Important Note: Disconnect power from your computer system before beginning installation. Remove computer cover and faceplate if required. Refer to your computer systems manual for removal information. If the DVD Rewriteable drive is replacing a CD-ROM or DVD-ROM, remove drive presently installed in your system. Your Toshi
ملخص المحتوى في الصفحة رقم 7
Power Cable - Connect an internal computer power supply cable to the power socket at the back of the DVD Rewriteable drive. One side of the plug has chamfered edges, so the power connector fits only one way. Push plug completely into the socket making sure the plug fits correctly. Figure 4.Installing Power Cable Audio Cable (optional) - If you have a sound card and speakers, and would like to play audio CDs on your computer, you will need to install a CD/DVD audio cable. Tos
ملخص المحتوى في الصفحة رقم 8
Software Driver - Toshiba's optical drives do not require any unique device drivers for Windows '95/'98/2000/Me/XP/NT. After installing your drive and re-booting, your system should recognize your drive. Windows '95/'98/2000/Me/XP/NT Operating Systems support all Toshiba optical drives natively If you prefer using DOS, download the DOS ATAPI driver from our web site. Other Software - Additional software is required to use the SD-R5372 CD-R/-RW, DVD-R/-RW and DVD functions. When you purch
ملخص المحتوى في الصفحة رقم 9
USING THE DVD REWRITEABLE DRIVE – SD-R5372 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is mounted horizontally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's Loading tray by pressing the Eject Button. 2. Place disc or into drive's Loading tray 3. Press Eject button again or gently push on the open disc tray. Tray will automatically close. Inserting a Disc - Vertically To insert a disc in a drive that is mounte
ملخص المحتوى في الصفحة رقم 10
Figure 2.Inserting Disc Vertically Removing a Disc To remove a disc from the DVD Rewriteable drive, perform the following steps: 1. Open the Loading Tray by pressing the Eject Button. 2. Slide disc holders away from disc. 3. Grasp disc by edges, and lift out of loading tray. 4. Press Eject Button again to close Loading Tray. Software When you purchase the SD-R5372 as a Kit, it will include Nero6 OEM Suite Software. Nero6 OEM Suite 3 disc contains the following software: Nero B
ملخص المحتوى في الصفحة رقم 11
NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has printing on only half of the disc, or if there is a slight imbalance in the disc, the imbalance is greatly magnified by the high speed, causing the drive to vibrate or produce a fan-like noise. These effects are inherent in the high-speed technology and do not indicate a problem with the drive. Emergency Ejection CAUTION: The following procedure is intended only as a last resort when pressing the eject
ملخص المحتوى في الصفحة رقم 12
TROUBLESHOOTING – SD-R5372 Problem Solution Disc tray cannot be opened • Check that there is power to drive. • Use Emergency Eject instructions to open tray. Drive is not recognized by system • Is the drive connected properly? Are all cables plugged in properly (e.g. Power Cable, Interface Cable and Audio Cables). • Are the drive configuration jumpers on the DVD Rewriteable drive set properly? • Is the software driver loaded? On a step-by-step (F8) Boot of the system is th
ملخص المحتوى في الصفحة رقم 13
SPECIFICATIONS –SD-R5372 General Interface: ATAPI Applicable Write Format CD-R/-RW Disc at once, Track at once, Session at once, Packet write DVD-R Disc at once, Incremental write DVD-RW Disc at once, Incremental write, Restricted overwrite DVD+R Sequential Write DVD+RW Sequential Write, Random Write Applicable Write disc DVD-R, DVD-RW, DVD+R, DVD+R DL, DVD+RW, CD-R, CD-RW, High Speed CD-RW, Ultra Speed CD-RW Applicable Formats - Read: DVD-ROM, DVD-R/RW, DVD+R, DVD+RDL, DVD+RW
ملخص المحتوى في الصفحة رقم 14
Performance Rotational Speed DVD-ROM (single layer) 9,200rpm (6.6 - 16X CAV) DVD-ROM (dual layer) 7,580rpm (5 - 12X CAV) DVD-R, DVD+R (read) 6,900rpm (5 - 12X CAV) DVD-RW, DVD+RW (read) 5,300rpm (4 - 8X CAV) DVD-RAM (Ver 2.1) (read) 1,400 - 3,300rpm (2X ZCLV) DVD-R (Ver 2.0) (Write) 1,150 - 2,700rpm (2X CLV) 2,300 - 5,300rpm (4X CLV) 9,200rpm (4 - 16X* CLV) DVD-RW (Write) 580 - 1,350rpm (1X CLV) 1,150 - 2,700rpm (2X CLV) 2,300 - 5,300rpm (4X CLV) DVD+R (Write) 1,380 - 3,200
ملخص المحتوى في الصفحة رقم 15
Data Buffer 2MB Reliability MTBF 100,000 hours Power ON Hours 5,436 hours/year ON/OFF Cycles 313 cycles/year Number of Access 600,000 accesses/year Operating Duty Cycle 20% of Power ON time (Reading/Seeking) 2% of Power ON time (Writing/Seeking) MTTR 0.5 hours Environmental Ambient Temperature Operating 5º to 50º C (41º to 122º F) Storage -10º to 60º C (14º to 140 F) Shipping -40º to 65º C (-40º to 149º F) Temperature Gradient Operating 11º C /hour (max) Storage/S
ملخص المحتوى في الصفحة رقم 16
Connectors DC input 4-pin Power Supply Connector ATAPI Interface Connector 40 Pin I/F ATAPI Standard Audio Connectors 4-pin and 2-pin connector (use matching housing, Part No. 70066, made by Molex Corp, or equivalent) Regulatory The SD-R5372 DVD Writeable drive has been certified by the following regulatory agencies: • UL 1950 • CSA C22.2 No. 950 • TUV (EN60950I) • CE standard • DHHS 21 CFR Sub-Chapter J • FDA CFR21, EN60825 14
ملخص المحتوى في الصفحة رقم 17
DRIVE CONNECTORS –SD-R5372 Figure 1.SD-R5372 DVD Rewriteable Drive Rear Panel - Connectors Power is supplied to your DVD drive by the connection with your computer's +5V/+12V Power power cable to the power socket at the back of drive. One side of the plug has Connector chamfered edges, so the power connector fits only one way. CAUTION: Severe damage to the Drive circuits may occur if power cable is plugged in upside-down with power ON. Supplies Analog and Digital sound t
ملخص المحتوى في الصفحة رقم 18
Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN I/O SIGNAL HOST SIGNAL NAME PIN I/O SIGNAL HOST SIGNAL NAME NO. NAME NO. NAME 1 I Reset Host Reset 21 O HDRQ DMA Request 2 - GND 22 - GND 3 I/O HD7 Host Data Bus BIT 7 23 I HWR-,STOP Host I/O Write 4 I/O HD8 Host Data Bus BIT 8 24 - GND 5 I/O HD6 Host Data Bus BIT 6 25 I HRD-, Host I/O Read HDMARDY, - HSTROBE 6 I/O HD9 Host Data Bus BIT 9 26 - GND 7 I/O HD5 Host Data Bus BIT 5 27 O IORDY, I/O Channel Ready
