ملخص المحتوى في الصفحة رقم 4
TABLE OF CONTENTS SAFETY PRECAUTIONS ............................................................................................................................................... 2 QUICK START ................................................................................................................................................................ 5 INSTALLATION .................................................................................................................................
ملخص المحتوى في الصفحة رقم 5
QUICK START Connection with Other Devices Before connecting to other devices, ensure to turn off the power supply of the device to be connected with the digital video processor. Connecting to a Projector ● Read through the projector’s instruction manual thoroughly. ● Depending on the DVI cable used, signals may be attenuated and images may become unstable. Use high-quality DVI cables that are 5 m or shorter. When a DVI cable longer than 5 m is used, make use of a distribution system or an opti
ملخص المحتوى في الصفحة رقم 6
INSTALLATION 389pq OUTPUT INPUT RED/Pr GREEN/Y BLUE/Pb H/C SYNC V SYNC RS-232 I/R REMOTE SCREEN 100-240 VAC 50-60Hz 35 WATTS DVI INPUT DVI OUTPUT Y/C VIDEO RED/Pr GREEN/Y BLUE/Pb C-SYNC HDTV INPUT MONITOR OUTPUT 1 2 45 6 7 w 3 YPrPb/RGBs Input (BNC): 480i and HDTV scan rates are INSTALLATION sent to the internal processor and then output at the se- lected scan rate. If the output is set to analog RGBHV or Accessories digital DVI, the unit will automatically transcode the YPrPb
ملخص المحتوى في الصفحة رقم 7
Installation (continued) The following diagram offers one way to connect the system. 7 DVI Output: Digital output interface for compatible dis- plays. All processed analog and digital in- Satellite Receiver puts are output to this connector as well as YPrPb computer scan rates when the pass-through DVI S-Video HDTV input is selected. Maximum cable length is Alt. 50ft with a high quality DVI cable. For longer Conn. lengths a distribution system or fiber optic system must be used. S-Video HD/PC YP
ملخص المحتوى في الصفحة رقم 8
SETUP POWER 12 3 4 SETUP MENU FUNCTIONS FRONT PANEL CONTROL 1 Firmware Reset: SET : SCANRATE Push a small paper clip into this opening to reset the unit’s Select the required scanrate by using the right and left arrows. CPU. When the desired rate is displayed on the LCD display, press ● Use this reset only if the unit will not respond to commands. the STORE key. This unit will ask you “Are you sure” and It will not erase custom settings. Use the Factory Restore press the STORE key again. The sca
ملخص المحتوى في الصفحة رقم 9
Setup (continued) SET : PASSTHRU TRANSCODE SET : BLACK LEVEL (For setting the black level) Disable (Default) / Enable 7.5 IRE / 0 IRE (Default) YPrPb HDTV signals via the D15 input or the YprPb (BNC) For setting the black signal level of the video signal. When inputs can be transcoded to RGB when this feature is enabled. the video signal is “7.5 IRE Setup”, set to “7.5 IRE”. SET : DVI Input Level (For setting the gray scale) SET : COMPONENT INPUT STANDARD 16-235 / 0-255 (Default) DVD (Default) /
ملخص المحتوى في الصفحة رقم 10
IR REMOTE/OSD IR REMOTE AND OSD OPERATION ON SCREEN DISPLAY (OSD) This unit is now shipped with a simplified remote control that Accessing the OSD allows for direct access to most commands used to control 1. Press Menu button to bring up main Index. the processor. 2. Use Function Up/Down Keys until the triangle Adjustments can be made three different ways: at the top of the OSD turns yellow. 1. Press the Menu button to activate the OSD and use the 3. Use the Left/Right keys to move to the next m
ملخص المحتوى في الصفحة رقم 11
● When using a 4:3 source on a Wide Angle screen there Input Menu are black bars on the left and right of the image. The sidebars can be changed to gray using the Blanking Level control located in the Display menu. If filling the entire screen INPUT PICTURE PATTERNS DISPLAY is desired, select Letterbox. The image will fill the screen but the top and bottom 1/3 of the image will be cut off (overscanned). FORMATS When watching 2:35 aspect ratio movies on a 16:9 (1:77) INPUTS DVI screen, it is no
ملخص المحتوى في الصفحة رقم 12
Osd (continued) Display Menu Color Factory 50 Adjust the color density of the picture image. DISPLAY INPUT PICTURE PATTERNS Tint Factory 50 POSITION Tint is not available with YPrPb or PAL sources HORIZONTAL 25 Detail Factory 4 VERTICAL 25 ● The Detail circuit is a powerful tool for image quality. The settings have been optimized for the output scan rate and BORDER LVL 0 resolution. However, the viewer’s tastes plus the types of software and display require making adjustments of this LEFT RIGH
ملخص المحتوى في الصفحة رقم 13
RS232 Patterns Menu AVAILABLE PATTERNS The best approach to system setup is to use a DVD that offers the proper test patterns. This way, the system is Gray Step : Check gray scale aligned for the entire signal path. If a test DVD is not avail- Cb Ramp : Check linearity of Cb channel able, then use the internal test patterns provided in this Cr Ramp : Check linearity of Cr channel unit. Y Ramp : Check linearity of Y channel Black : Full Black screen ● The test pattern generator in this unit is
ملخص المحتوى في الصفحة رقم 14
RS232 (continued) Following the header, a comma is used to delimit the header from the command. All the commands with their descriptions are listed below. All the text strings are terminated with a carriage return (0x0d or 13). Maximum command string length is 250 characters. OPERATION COMMANDS (Used for day-to-day operation) OPTIONS OR RANGE DESCRIPTION COMMAND (0-2) 0=4x3,1=Letterbox, 2=Anamorphic Input Aspect Ratio – for all sources A# (0-170) 128 default Brightness B# (0-155) 110 default Con
ملخص المحتوى في الصفحة رقم 15
SETUP COMMANDS (Normally not controlled by RS232) OPTIONS OR RANGE COMMAND DESCRIPTION (0-192) BB# Bottom Blanking (0-252) BL# Border Level – black to white (0-255) BLT# LCD Backlite Timer on front panel 1=On 0=OFF CS# Composite Sync – for RGB output DVD DVI Input Disabled DVE DVI Input Enabler 1=On 0=OFF E# RS-232 ECHO EXTD PassThru Input Disabled EXTE PassThru Input Enabled (0-50) 25 default HP# Horizontal Position (0-200) LB# Left Blanking (0-1) [0=RGB, 1=YPrPb] M# Output Mode OSDOFF OSD Off
ملخص المحتوى في الصفحة رقم 16
HELP MENUS TEST PATTERN HELP MENU TP0 TEST PATTERN OFF TP1 100% COLOR BARS TP2 REVERSE COLOR BARS TP3 10 STEP GREY TP4 LUMA RAMP TP5 CB RAMP TP6 CR RAMP TP7 BLACK SCREEN TP8 GREEN SCREEN TP9 RED SCREEN TP10 BLUE SCREEN TP11 CONVERGENCE TP12 ACTIVE BORDER TP13 SMPTE PATTERN TP14 WHITE WINDOW TP15 PLUGE Output Scan Rate Horizontal Frequency Vertical Frequency 1920 x 540P 33.8 KHz 59.94 Hz 720 x 576P 31.3 KHz 50.00 Hz 800 x 600P 37.6 KHz 59.94 Hz 1280 x 720P 45.0 KHz 59.94 Hz 1280 x 720P 37.5 KHz 5
ملخص المحتوى في الصفحة رقم 1
®
Machine Models Compatible for Con-
nection with this Product
DLA-HD2KU
This product (LD-HD2KU) is exclusively for the
above-mentioned model. The performance cannot
be guaranteed when using with other models.
This processor is used as a dedicated machine and
this manual (instruction manual) may contain de-
scription of features as well as specifications not
used by the processor.
DLA-HD2KE
This product (LD-HD2KE) is exclusively for the
above-mentioned model. The performance cannot
be guaranteed
ملخص المحتوى في الصفحة رقم 2
SAFETY PRECAUTIONS IMPORTANT INFORMATION IMPORTANT SAFEGUARDS WARNING: TO PREVENT FIRE OR SHOCK HAZ- IMPROPER USE OF THIS EQUIPMENT CAN RESULT ARDS, DO NOT EXPOSE THIS APPLIANCE TO RAIN IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZ- OR MOISTURE. ARD. In order not to defeat the safeguards incorporated into this product, observe the following basic rules for its installation, CAUTION: use and service. To reduce the risk of electric shock, do not remove cover. – All the safety and operating instruction
ملخص المحتوى في الصفحة رقم 3
– Do not overload wall outlets, extension cords, or conve- *DO NOT allow any unqualified person to install the nience receptacles on other equipment as this can result unit. in a risk of fire or electric shock. Be sure to ask your dealer to install the unit since special –Never push objects of any kind into this product through technical knowledge and skills are required for installation openings as they may touch dangerous voltage points or and connection to multiple devices. short out parts th
ملخص المحتوى في الصفحة رقم 17
SPECIFICATIONS Model Name/ Article Name LD-HD2KU/LD-HD2KE Digital Video Processor Colour System NTSC, PAL (Auto switching) Video Input Signal Horizontal Frequency Vertical Frequency 480i 15.7 KHz 29.97 Hz 480p 31.5 KHz 59.97 Hz 576i 15.6 KHz 25.00 Hz 576p 31.3 KHz 50.00 Hz 720p 37.5 KHz 50.00 Hz 720p 45.0 KHz 59.97 Hz 1080i 28.1 KHz 25.00 Hz 1080i 33.7 KHz 29.97 Hz Input Terminals VIDEO 1-line, BNC x 1 1.0 Vp-p Y/C 1-line, mini-DIN 4 pin x 1 Y: 1.0 Vp-p, C: 0.286 Vp-p R,G,B,C-SYNC 1-line
ملخص المحتوى في الصفحة رقم 18
MEMO ......................................................................................................................... ......................................................................................................................... ......................................................................................................................... ......................................................................................................................... .......
ملخص المحتوى في الصفحة رقم 19
ملخص المحتوى في الصفحة رقم 20
LD-HD2KU/LD-HD2KE DIGITAL VIDEO PROCESSOR ® VICTOR COMPANY OF JAPAN, LIMITED Printed in Japan 0504-SW-VP © 2004 VICTOR COMPANY OF JAPAN, LIMITED
