ملخص المحتوى في الصفحة رقم 1
EZQuest Duplicators
King Boa DVD Duplication
User's Manual
ملخص المحتوى في الصفحة رقم 2
Copyright and Trademark The information in this manual is subject to change without prior notice and does not represent a commitment on the part of vendor, who assumes no liability or re- sponsibility for any errors that may appear in this manual. This manual contains materials protected under International Copyright Laws. All rights reserved. No part of this manual may be reproduced, transmitted or tran- scribed without the expressed written permission of the manufacturer and author of this m
ملخص المحتوى في الصفحة رقم 3
EZQu Buttons and LCD There are four buttons and an LCD on the panel of the copy smart plus. They are described as follows. 1 2 4 EZQuest 3 5 1. It shows all functions and messages. 2. It is used to scroll up through functions or menus. 3. It is used to scroll down through functions or menus. 4. It is used to execute a selected function. 5. It is used to cancel a selected function. After you power on,and the King Boa detects installed hard
ملخص المحتوى في الصفحة رقم 4
3. 4. 1. Copy Detect Drives There are 12 functions for you to use. Function 1 is Copy. You can press t to select other functions. l Place a source DVD into DVD-ROM. l Switch to function 1 Copy by pressing s . Place blank DVD disks into the DVD writers, and press ENT to start copying. l When copying comes to an end, the passed DVDs will eject automatically. The default is eject automatically, but you can change it. l The failed DVDs will remain in the writers. The default is keeping f
ملخص المحتوى في الصفحة رقم 5
Chapter 5 Functions There are 12 functions: Copy, Test, Test & Copy, Verify, Compare, Prescan, Disc Info, Select Source, Image, Edit Track, Setup and Advanced Setup. Among the 12 functions, Edit Track is designed exclusively for editing a collection of favorite songs from CDs. During operation if you do not understand an LCD message, you can see Appendix 2. 5.1 Copy Function 1 Copy is to copy data from a source DVD directly into blank DVD disks. Before copying be sure that the source DVD is
ملخص المحتوى في الصفحة رقم 6
When copying is in progress, MB and time will decrease whereas the percentage of completion increase. When copying comes to an end, LCD will show the results as follows. The passed DVDs will eject automatically. 1.Copy OK: 03 5.2 Test Function 2 Test is to simulate the copying progress. When simulation finishes, there will be no data really written into DVD disks. Select function 2. Put a source DVD onto DVD-ROM and blank DVD disks onto the DVD writers. 2.Test Press ENT to start simulation. If
ملخص المحتوى في الصفحة رقم 7
LCD will show the testing information as follows. Testing- DVD 0% 4213.4MB d:20:15 When the test comes to an end, LCD will show the results as follows. 2.Test OK: 03 Stopping the test halfway does not affect the DVD disks, but if the DVD-rewriteable disks contain important data, they may be destroyed. 5.3 Test & Copy Function 3 Test & Copy is to test first and then copy actually. Select function 3. Put a source DVD onto DVD-ROM and blank DVD disks onto the DVD writers. 3.Test & Copy
ملخص المحتوى في الصفحة رقم 8
When the test finishes, actual copying will begin as shown below. Copying- DVD 0% 4213.4MB d:20:15 When the whole process finishes, LCD will show the results as follows. 3.Test & Copy OK: 03 5.4 Verify Function 4 Verify is to examine if the target DVDs can be read correctly after copying. Select function 4. 4.Verify Press ENT to verify. LCD will show the verification information as follows. Verify- DVD 0% 4213.4MB 2:29:14 Page 8
ملخص المحتوى في الصفحة رقم 9
When verification comes to an end, LCD will show the results as follows. 4.Verify OK: 03 5.5 Compare Function 5 Compare is to make a comparison between the source DVD and the target DVDs after copying. Select function 5. Put the source DVD onto DVD-ROM and the target DVDs onto DVD writers. 5.Compare Press ENT to compare.LCD will show the comparison information as follows. Compare- DVD 0% 4213.4MB 1:05:06 When comparison comes to an end, LCD will show the results as follows. Compare O
ملخص المحتوى في الصفحة رقم 10
Press ENT to see the details of source 1 as shown below. Src: 01 DVD-ROM Total: 4213.4MB Press ENT to see the details of source 2. If the comparison is identical, LCD will show the message as follows. Src: 02 DVD-RW Identical If comparison fails, LCD will show the failure. By pressing ENT twice, LCD will show that the contents of source 1 and those of source 2 do not match as follows. Src: 02 DVD-RW TOC not match 5.6 Prescan Function 6 Prescan is to scan if the source DVD can be
ملخص المحتوى في الصفحة رقم 11
Press ENT to prescan. LCD will show the scanning information as follows. Scaning- DVD 0% 4213.4MB 40:40 When scanning finishes, and the source DVD can be read correctly, LCD will show the results as follows. PreScan OK! 5.7 Disc Info Function 7 Disc Info is to show the basic information of source DVD. Select function 7. Put the source DVD onto DVD-ROM. 7.Disc Info Press ENT , and LCD will show the DVD information as follows. Disc Type: DVD-ROM Capacity: 4213.4MB Page 11
ملخص المحتوى في الصفحة رقم 12
5.8 Select Source Function 8 Select Source is to let you select the data on DVD-ROM, DVD writers or HDD as the source from which copying will be done. Select function 8. 8.Select Source Press ENT , and then press s t to select the source as shown below. Src: DVD-ROM 01 IDE1 Master After selecting the source such as DVD-ROM, you can press ENT , and LCD will show the message as follows. DVD-ROM selected! Suppose you select HDD as the source and try to copy from one of its partitions, but the
ملخص المحتوى في الصفحة رقم 13
5.9 Image Function 9 Image is valid only when you have installed a hard disk. This function includes 6 parts. They are Load, Delete Image, Image Info, Compare Image, Select Partition and Select Src Drive. The loaded data is called an image file. Select function 9. 9.Image 5.9.1 Load On the above figure press ENT, and you will enter the following figure. Here the function Load is to let you load data from DVD-ROM or any one of the DVD writers into the current partition of the hard disk. P:A me
ملخص المحتوى في الصفحة رقم 14
After the image file is successfully loaded, LCD will show the results as follows. Image load OK If there is an image file existing in the current partition, the system will ask you whether to overwrite it or not. Please use s t to confirm Yes or No. Image Exists Overwrite?Yes 5.9.2 Delete Image If you want to empty an image file stored in a particular partition, you can use the function Delete Image to do so. First, select the function by pressing t . 9-02. Image P: A Delete Image The system
ملخص المحتوى في الصفحة رقم 15
After the image file is deleted, LCD will show the results as follows. Partition A: Image is deleted 5.9.3 Image Info This function is to show the basic information of an image file stored in a particular partition. First, select the function by pressing t . 9-03.Image P: A Image Info Press ENT , and LCD will show the information of the image file as follows. Disc Type: DVD-ROM Capacity: 4213.4MB 5.9.4 Compare Image This function is to compare the contents of the source DVD and those
ملخص المحتوى في الصفحة رقم 16
Press ENT , and LCD will show the comparison information as follows. Compare- DVD 0% 4213.4MB 1:05:06 When comparison comes to an end, LCD will show the results as follows. Compare OK: 1 Fail: 0 Diff: 0 Press ENT to see the details of source 1 as shown below. Src: 01 DVD-ROM Total: 4213.4MB Press ENT to see the details of source 2. If the comparison is identical, LCD will show the message as follows. Tgt: 00 HDD P: A Identical If comparison fails, LCD will show th
ملخص المحتوى في الصفحة رقم 17
5.9.5 Select Partition This function is to select a partition in the hard disk. First, select the function by pressing t . 9-05.Image P: A Select Partition After installing a hard disk, your copy smart plus will format it automatically. Each partition will occupy 5GB. The number of partitions is dependent on the hard diskís capacity. The partitions is alphabetically arranged. Now select a working partition by pressing s t , and LCD will show the message as follows. Select Working Partiti
ملخص المحتوى في الصفحة رقم 18
First, select the function by pressing t . 9-06. Image P: A Image Src Drive Then, use s t to select DVD-ROM or any of the DVD writers as the source. Select Img Src: 01 IDE1 DVD-ROM After selecting the source such as DVD-ROM, you can press ENT , and LCD will show the message as follows. Load image from Drive ID-01 5.10 Edit Track (for CD only) Function 10 Edit Track is exclusively designed for editing a collection of favorite songs from CDs. In other words, it can collect different
ملخص المحتوى في الصفحة رقم 19
Select function 10. 10. Edit Track 5.10.1 CD to CD On the above figure press ENT, and you will enter the following figure.Here the function CD to CD is to let you select a track or more from CD-ROM, and then copy into blank CD-R/RWs. 10-01. Edit Track CD to CD Edit On the above figure press ENT , and you will enter the following figure. Here 1/10 means the number one of the 10 tracks, and 03:25 means the playing time. Select Track: 1/10 03:25 You can press t to see the second track an
ملخص المحتوى في الصفحة رقم 20
After selecting, please use s to move to the ìEndî menu as shown below. Select Track: End 1Trk03:25 Press ENT to finish the CD editing, and use s t to confirm Yes or No. End edit disc and burn?Yes LCD will show the copying information as follows. Copying- 24X Edit 1/10 - > 1/1 On the above figure 1/1 means the first track of all tracks we have selected, and here we have just selected one track. When copying comes to an end, LCD will show the message as follows. Burn Complete! OK: 03 Pag
