ملخص المحتوى في الصفحة رقم 1
OWNER'S MANUAL
DC-650A Dust Collector
WMH TOOL GROUP
Consumer/Light Industrial Products Division
P.O. BOX 1349
Auburn, WA 98071-1349
Ph: 1-800-274-6848 ▪ Fax: 1-800-274-6840
E-mail: jet@wmhtoolgroup.com
www.wmhtoolgroup.com M-708640 2/03
Copyright © WMH Tool Group
ملخص المحتوى في الصفحة رقم 2
This manual has been prepared for the owner and operators of JET’S DC-650A. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life and efficiency from your Dust Collector, and to aid in using the machine safely, read this manual thoroughly and follow instructions carefully. Warranty
ملخص المحتوى في الصفحة رقم 3
WARNING 1. Read and understand the entire contents of this manual before attempting assembly or operation. Do not use this machine until proper training and knowledge has been obtained. 2. Do not leave Dust Collector when plugged in. Unplug from outlet when not in use and before servicing. 3. Do not use outdoors or on wet surfaces. 4. Do not allow to be used as a toy. Close attention is necessary when used near children. 5. Use only as described in this manual. Use only manufactu
ملخص المحتوى في الصفحة رقم 4
Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local co
ملخص المحتوى في الصفحة رقم 5
230 Volt Operation If 230V, single phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This dust collector is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B. 3. The 115V attachment plug supplied with the dust collector must be replaced with a UL/CSA listed plug suitable for 230V operation. Co
ملخص المحتوى في الصفحة رقم 6
Specifications: DC-650A Stock Number................................................................................................................................ 708640 Blower Wheel Diameter....................................................................................................................9-1/2" Sound Rating at 3 feet......................................................................................................................88 dB Hose Diameter...................
ملخص المحتوى في الصفحة رقم 7
WARNING Read and understand the entire contents of this manual before attempting assembly or operation of the dust collector! Failure to comply may cause serious injury! Unpacking 1. Remove all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly. Contents of the Shipping Carton DC-650A 1. Base 1. Owner's Manual 1. Warranty C
ملخص المحتوى في الصفحة رقم 8
Assembly WARNING The dust collector must be disconnected from the power source during assembly. Failure to comply may result in serious injury! 1. Place motor housing on the floor with the motor fan facing upwards as shown in Figure 1. 2. Attach support cylinder (A, Fig. 2) to the motor housing with three M6x16 socket head cap screws and three M6 flat washers (B, Fig. 2). 3. Mount two fixed casters (C, Fig. 3) to the appropriate end of base (
ملخص المحتوى في الصفحة رقم 9
7. Thread a M6 hex nut onto the filter bag 5. Turn the bag outside in and re-attach to the support rod, follwed by a M6 flat washer and housing using the retainer strap to secure. M6 lock washer (A, Fig. 5). Thread the support rod (B, Fig. 5) into the motor/fan housing and tighten nut against housing. 8. Place the retaining strap (C, Fig. 5) through the loops on the filter bag and hang the filter bag from the hook. 9. Secure bag to housing with retaining strap. Note: The ret
ملخص المحتوى في الصفحة رقم 10
Removing the Collector Bag Turning the Machine On & Off Before hooking up to the power source, make CAUTION sure that the switch is in the off position. Wearing a particle mask/respirator for protection against fine dust particles during The dust collector can be turned on by flipping cleaning is highly recommended. the start switch up. Flip the switch down to turn the dust collector off. There is a removable key that can be used to lock the machine in the 1. Disconnect the m
ملخص المحتوى في الصفحة رقم 11
Parts Breakdown for DC-650A Dust Collector 11
ملخص المحتوى في الصفحة رقم 12
Parts List for the DC-650A Dust Collector Index Part No. No. Description Size Qty. 1..........422109W ..................... Impeller Housing.................................... ...............................................1 2..........MH422001 ................... Motor .................................................... ...............................................1 ............CA020010.................... Starting Capacitor (not shown)...............200MFD, 125V................
ملخص المحتوى في الصفحة رقم 13
Wiring Diagram 13
