ملخص المحتوى في الصفحة رقم 1
This Manual is Bookmarked
Operating Instructions and Parts Manual
Dust Collector
Model: DC-650A/C/ARC/CRC
DC-650ARC shown DC-650C shown
WMH TOOL GROUP
2420 Vantage Drive
Elgin, Illinois 60123 Part No. M-708640
Ph.: 800-274-6848 Revision G1 12/04
www.wmhtoolgroup.com Copyright © WMH Tool Group
ملخص المحتوى في الصفحة رقم 2
This manual has been prepared for the owner and operators of the JET DC-650 Series Dust Collectors. Its purpose, aside from machine operation, is to promote safety using accepted operating and maintenance procedures. To obtain maximum life and efficiency from your dust collector and to aid in using it safely, please read this manual thoroughly and follow the instructions carefully. Warranty and Service WMH Tool Group warrants every product it sells. If one of our tools needs service or repa
ملخص المحتوى في الصفحة رقم 3
Table of Contents Warranty and Service ...........................................................................................................................................2 Table of Contents..................................................................................................................................................3 Warnings................................................................................................................................................
ملخص المحتوى في الصفحة رقم 4
Warnings 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This dust collector is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a dust co
ملخص المحتوى في الصفحة رقم 5
blahblahblah 20. Make your workshop child proof with padlocks, master switches or by removing starter keys. 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings, metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with any part of the dus
ملخص المحتوى في الصفحة رقم 6
Introduction This manual is provided by JET covering the safe operation and maintenance procedures for models DC-650 Series Dust Collectors. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance to instructions set forth in this manual. If there are any questions or comments, please contac
ملخص المحتوى في الصفحة رقم 7
Unpacking 1. Remove all contents from the shipping carton. DC-650C Contents 2. Report any damage to your distributor. Canister Filter Box 3. Do not discard any shipping material until after 1 – Canister Filter the dust collector has been assembled and is 1 – Handle running properly. 1 – Bag of Hardware for Handles 2 – M10 Hex Nuts 2 – M10 Flat Washers 1 – M10 Lock Washer Contents of the Shipping Carton 4 – Knobs 1 – M8 Hex Nut 1 – M8 Flat Washer DC-650A Content
ملخص المحتوى في الصفحة رقم 8
Assembly The dust collector must be disconnected from the power source during assembly. Failure to comply may result in serious injury! Motor Housing and Support Canister 1. Place the impeller housing (A, Fig. 1) on the floor with the motor (B, Fig. 1) facing upwards as shown. 2. Attach the fan (C, Fig. 1) to the motor shaft Figure 1 (D, Fig. 1). Allow a 1/16"-1/8" clearance between the fan (C, Fig. 1) and housing (E, Fig. 1). 3. Secure the fan (C, Fig. 1) by tightening the hex
ملخص المحتوى في الصفحة رقم 9
Filter Bag Installation – DC-650A/ARC 1. Thread an M6 hex nut onto the filter bag support rod, followed by an M6 flat washer and M6 lock washer (A, Fig. 5). Thread the support rod (B, Fig. 5) into the motor/fan housing and tighten nut against the housing. 2. Place the retaining strap (C, Fig. 5) through the loops on the filter bag and hang the filter bag from the hook. 3. Secure bag to housing with retaining strap. Note: The retainer strap should be tight enough to provide a good
ملخص المحتوى في الصفحة رقم 10
Canister Installation – DC-650C/CRC 1. Place the canister filter so that it fits snugly over the housing and tighten the four knobs (A, Fig. 7). 2. Mount handle (B, Fig. 7) to the arm (C, Fig. 7) with a M8 flat washer (D, Fig. 7), M8 lock washer (E, Fig. 7), and a M8 hex nut (F, Fig. 7). 3. Thread a M10 hex nut (G, Fig. 7) onto the threaded rod found on top of the canister filter followed by a M10 lock washer (H, Fig. 7), and M10 flat washer (I, Fig. 7). 4. Mount the arm (C, Fig. 7) t
ملخص المحتوى في الصفحة رقم 11
reached. The dust collector will run for the amount of time displayed on the digital display. If you scroll past Electrical Connections 99 and release the button at 10, for example, the machine will run for ten minutes, not 110 minutes. All electrical connections must be done by a qualified If the OFF button is pressed while machine is running electrician. All adjustments or repairs must be with the timer engaged, the machine turns off and the done with the dust collector disconnecte
ملخص المحتوى في الصفحة رقم 12
To reduce the risk of injury from Maintenance moving parts, always keep the inlet connected to Never perform maintenance on the flexible hose. Failure to comply may result in this machine before turning serious injury! switch off and removing plug from power source. Failure to comply may cause serious injury! Cleaning the Filter – DC-650C/CRC Clean both the filter and collector bag frequently to Cleaning the Filter Bag – DC-650A/ARC keep the collector's performance at its optimum.
ملخص المحتوى في الصفحة رقم 13
Parts Replacement Parts Replacement parts are listed in the Parts List on the following pages. To order parts or reach our service department, call 1-800-274-6848 between 7:00 a.m. and 6:00 p.m. (CST), Monday through Friday. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Parts List Index No. Part No. Description Size Qty 1............... 422109W ................. Impeller Housing.....................
ملخص المحتوى في الصفحة رقم 14
Index No. Part No. Description Size Qty 35............. 331010..................... Shaft .......................................................................................................................1 36............. 331043..................... Scraper ...................................................................................................................2 37............. 331015..................... Plate...................................................................
ملخص المحتوى في الصفحة رقم 15
Parts Breakdown for DC-650C/CRC Models for DC-650A/ARC Models 15
ملخص المحتوى في الصفحة رقم 16
Remote Control Breakdown for DC-650ARC/CRC Index No. Part No. Description Size Qty ................. DC650RC-100......... Receiver Assembly (Items 1-11) ............................................................................1 1............... DCRC-101............... Label.......................................................................................................................1 2............... DCRC-102............... Counter Screw............................................
ملخص المحتوى في الصفحة رقم 17
Wiring Diagrams DC-650A/C Models 115V 230V 17
ملخص المحتوى في الصفحة رقم 18
DC-650ARC/CRC Models 18
ملخص المحتوى في الصفحة رقم 19
Notes 19
ملخص المحتوى في الصفحة رقم 20
WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone: 800-274-6848 www.wmhtoolgroup.com 20
