ملخص المحتوى في الصفحة رقم 1
REVISED 1/18/99
1
User’s Manual for
Tapeless Digital
Answering System
with Time/Day AS45
Fold open this manual for information
about this product’s installation and
operation. Please read Part 1 –
Important Product Information,
included in this package.
Part 2
© 1999 Lucent Technologies Consumer Products L.P. All rights reserved.
Printed in Mexico. 848317715 Issue 1AT&T
ملخص المحتوى في الصفحة رقم 2
INSTALLATION TEL LINE TEL SET Strain Telephone Relief Tab Set Cord Modular Standard Telephone Electrical Jack Outlet Power Cord Telephone Line Cord 1 Connect the telephone line cord. 3 Connect the power cord. Plug one end of the telephone line Plug the power cord into the jack cord into the jack labeled TEL LINE labeled POWER and into an electrical on the back of the system. Plug the outlet not controlled by a wall switch. other end into a modular telephone Fit the power cord behind the strain
ملخص المحتوى في الصفحة رقم 3
OPERATION Displays number of messages and other information Adjust volume Set and hear Delete all time/day or selected messages Use with other buttons to change/hear settings Turn system on or off Record and play outgoing announcement / Skip all or part of a message Microphone Play/Stop messages Record a memo / Repeat all or part of a message PLAY Light indicates messages Setting the Clock Recording Your Announcement You’ll need to set the clock so that it can Before using this answering system,
ملخص المحتوى في الصفحة رقم 4
OPERATION Press P to exit Answering Calls — OR — When the system answers a call, the caller The system will time out after 30 seconds hears the announcement you recorded, and save any changes already made. followed by a beep. After the beep, the system begins recording your caller’s Ring Select and Toll Saver message. A caller can leave a message up Use Ring Select to choose how many times to three minutes long. If the message is the line will ring before the system longer than three minutes,
ملخص المحتوى في الصفحة رقم 5
OPERATION Announcement Monitor Saving Messages You can choose whether to hear the The system automatically saves your announcement when your system answers messages if you do not delete them. The a call, or have it silent (off) on your end system can save about 12 minutes of (your caller will still hear an messages, including your announcement, announcement). for a total of up to 59 messages. When memory is full, you must delete some or 1 Press and hold S. After the Ring all messages before n
ملخص المحتوى في الصفحة رقم 6
REMOTE OPERATION Connect with the Deleting Messages Delete All Messages Answering System After you have listened to all messages and 1 Dial your telephone number from a heard the two beeps, press 3 3. touch tone phone with a different telephone number. Delete Selected Messages 2 When the system answers, enter your Press and release 3 while the message you three-digit Access Code during or want to delete is playing. after the announcement. The system announces the number of messages, Record Anno
ملخص المحتوى في الصفحة رقم 7
REMOTE OPERATION Turn System Off Memory Full The system answers after 10 rings, then Press 0 0. announces “Memory is full,” and beeps Turn System On twice, you must delete messages to make room for new ones. When the system is off, it answers after 10 rings, announces “The machine is off,” and 1 Enter the Remote Access Code after beeps twice. two-beep signal. 1 Press 0 to turn the system on. 2 Listen to messages, and delete some or all of them. 2 The system beeps twice and is ready to answer cal
ملخص المحتوى في الصفحة رقم 8
IN CASE OF DIFFICULTY If this answering system does not work System Does Not Respond To Remote properly, try the following suggestions. Commands If you’re still having difficulty, call • Make sure you are calling from a 1 800 722–9125. touch tone phone. When you dial a number, you should hear tones. If you Message Window Is Blank hear clicks instead, the phone is not a • Make sure the power cord is securely touch tone telephone. connected to both the answering • The answering system may not de
ملخص المحتوى في الصفحة رقم 9
REVISED 1/15/99 fold fold a a a aaaaaaaaaaaaaaaaaaaaaaaaaaa a a a aaaaaaaaaaaaaaaaaaaaaaaaaaa 1 1 Tapeless Digital Answering System AS45 Tapeless Digital Answering System AS45 Remote Commands Remote Commands To connect with your answering system: To connect with your answering system: 1 Dial your telephone number from a touch tone phone. 1 Dial your telephone number from a touch tone phone. 2 When the system answers, enter your Remote Access 2 When the system answers, enter your Remote Access Co
ملخص المحتوى في الصفحة رقم 10
ONE KEY REMOTE COMMANDS ONE KEY REMOTE COMMANDS Play All Play New Delete Play All Play New Delete Repeat Stop/Exit Skip Repeat Stop/Exit Skip Annc. Annc. System Record System Record On Memo On Memo TWO KEY REMOTE COMMANDS TWO KEY REMOTE COMMANDS Turn system off 0 0 Turn system off 0 0 Delete all messages 3 3 Delete all messages 3 3 Review announcement7 1 Review announcement7 1 Record announcement7 *, speak after beep, press 5 Record announcement7 *, speak after beep, press 5 to stop to stop Room
ملخص المحتوى في الصفحة رقم 11
INSTALLATION OPERATION OPERATION REVISED 1/18/99 TEL LINE TEL SET Press P to exit Answering Calls When the system answers a call, the caller — OR — The system will time out after 30 seconds hears the announcement you recorded, Displays number and save any changes already made. followed by a beep. After the beep, the of messages and other information system begins recording your caller’s Ring Select and Toll Saver message. A caller can leave a message up Strain Adjust volume Use Ring Select to
ملخص المحتوى في الصفحة رقم 12
OPERATION REMOTE OPERATION REMOTE OPERATION IN CASE OF DIFFICULTY Announcement Monitor Saving Messages If this answering system does not work System Does Not Respond To Remote Connect with the Deleting Messages Turn System Off Memory Full You can choose whether to hear the The system automatically saves your properly, try the following suggestions. The system answers after 10 rings, then Commands Answering System Delete All Messages Press 0 0. announcement when your system answers messages if yo
