ملخص المحتوى في الصفحة رقم 1
®
H O M E A P P L I A N C E S
Installation Instructions
Undercounter Dishwasher
Instructions d'installation
Lave-vaisselle encastré
Table of Contents.............................................................................2
Table des matières.........................................................................20
W10078153B
ملخص المحتوى في الصفحة رقم 2
Installation Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Table of Contents Prepare cabinet opening Dishwasher Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 using existing utility hookups . . . . . . . . . . . . . . . . . . . . . 6 Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Prepare cabinet opening Tools and parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 where there are no e
ملخص المحتوى في الصفحة رقم 3
Installation Requirements Location Requirements Do not run drain lines, water lines or electrical wiring where Tools and Parts they can interfere with or contact dishwasher motor or legs. Gather the required tools and parts before starting The location where the dishwasher will be installed must installation. provide clearance between motor and flooring. Motor should not touch the floor. All installations Do not install dishwasher over carpeted flooring. Tools needed: • flashlight Protect dishw
ملخص المحتوى في الصفحة رقم 4
Product dimensions Cutout dimensions 24-7/8" (63.2 cm) 3/4" (1.9 cm) insulation – front vent 24-1/2" (62.2 cm)* may be compressed (not used on 24" (61 cm)** all models) All surfaces must be free from intrusions 33-7/8" (86 cm) min. 24" (61 cm) with wheels min. 34" removed (86.4 cm) min.* 3-1/4" 3-1/4" (8.3 cm) (8.3 cm) 2" 2" (5.1 cm) (5.1 cm) 5-1/2" 3-1/2" (14 cm) 6" *** 21" (53.3 cm) (8.9 cm) 6" *** (15.2 cm) (15.2 cm) 2" SIDE VIEW 9" (5.1 cm) 10" (22.9 cm) (25.4 cm) 2-3/4" 3-1/4" 3-
ملخص المحتوى في الصفحة رقم 5
Drain Requirements Electrical Requirements • Use the new drain hose supplied with your dishwasher. Contact a qualified electrician. If this is not long enough, use a new drain hose with a Assure that the electrical installation is adequate and in maximum length of 12 feet (3.7 m) that meets all current conformance with all national and local codes and AHAM/IAPMO test standards, is resistant to heat and ordinances. detergent, and fits the 1" (2.5 cm) drain connector of the You must have: dishwash
ملخص المحتوى في الصفحة رقم 6
Installation Instructions Install the drain hose IMPORTANT: Always use a new drain hose even when installing a new replacement dishwasher. WARNING 1. Drill a 1-1/2" (3.8 cm) diameter hole in cabinet wall or floor on the side of the opening closest to the sink. Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. 2. Connect drain hose to waste tee or waste disposer using one of the following methods: Failure to do so can result
ملخص المحتوى في الصفحة رقم 7
Option 2: No waste disposer – with air gap: Option 4: No waste disposer – no air gap: 1. Cut end of drain hose if needed (do not cut ribbed 1. Cut end of drain hose if needed (do not cut ribbed section). section). 2. Attach drain hose to air gap with large spring-type 2. Attach drain hose to waste tee with 1-1/2" to 2" clamp. If the drain hose was cut, use a 1-1/2" to 2" (3.8 to 5 cm) screw-type clamp*. (3.8 to 5 cm) screw-type clamp*. This connection must be before the drain trap and at 3. Use
ملخص المحتوى في الصفحة رقم 8
Option 2: Power supply cord method: Install the drain hose NOTE: A mating, three prong, ground-type wall receptacle is IMPORTANT: Always use a new drain hose. required in a cabinet next to the dishwasher opening. 1. Drill a 1-1/2” (3.8 cm) 1. Drill a 1-1/2” optional preferred diameter hole in cabinet (3.8 cm) hole in locations locations wall or floor on the side the cabinet rear of the opening closest or side. Preferred to the sink. and optional locations are 2. Connect drain hose to shown. was
ملخص المحتوى في الصفحة رقم 9
Option 2: No waste disposer – with air gap: Option 4: No waste disposer – no air gap: 1. Cut end of drain hose if needed (do not cut ribbed 1. Cut end of drain hose if needed (do not cut ribbed section). section). 2. Attach drain hose to air gap with large spring-type 2. Attach drain hose to waste tee with 1-1/2" to 2" clamp. If the drain hose was cut, use a 1-1/2" to 2" (3.8 to 5 cm) screw-type clamp*. (3.8 to 5 cm) screw-type clamp*. This connection must be before the drain trap and at 3. Use
ملخص المحتوى في الصفحة رقم 10
7. Remove terminal box cover. Prepare dishwasher – If you are direct wiring: install a U.L.-listed/CSA- certified clamp connector to the terminal box. If using conduit, use a U.L.-listed/CSA-certified conduit WARNING connector. – If you are installing a power supply cord kit, do so now, following kit instructions. terminal box cover ADVERTENCIA Tip Over Hazard Do not use dishwasher until completely installed. AVERTISSEMENT Do not push down on open door. Doing so can result in serious injury or
ملخص المحتوى في الصفحة رقم 11
3. Add shims as needed in the area shown to bring ® Install door panel—Pro Line series dishwasher up to proper height. NOTE: Shims must be securely attached to floor to For top vented models with a factory-supplied stainless or prevent their movement when the dishwasher is painted full front panel: operated. 1. Remove the carton containing the factory-supplied full front panel. 2" 2. Remove the handle package from the front of the (5.1 cm) shipping base. shim shim ® 3. With a TORX screwdriver,
ملخص المحتوى في الصفحة رقم 12
9. Install the two #8-18 x 1-3/8" screws from the literature For dishwashers with the control panel shown below: package in the top corners, as shown. Align top edges of (Models KUDC03IT, KUDK03IT and KUDL03IT) full front panel and console; tighten corner screws. 2 screws (Your model may vary slightly from picture above.) Custom door panel dimensions are: align top edges *25-29/32" (65.8 cm) 23-3/8" (59.4 cm) 1-3/8"screw 3/4" (19.1 10. Tighten the two side screws reinstalled in Step 8. mm) 11.
ملخص المحتوى في الصفحة رقم 13
4. Measure 9-29/32" (25.2 cm) from top edge and mark a line Install custom panel on the back of customer-supplied custom panel. Option 1: For models KUDS03FTPA and KUDU03FTPA NOTE: The handle for the custom panel is not included. IMPORTANT: If the handle is attached from the back of the 9-29/32" back custom panel, the screw holes should be countersunk for (25.2 cm) the screws heads to be flush with the panel. If the handle is attached to the front of the custom panel, the screw lengths cannot e
ملخص المحتوى في الصفحة رقم 14
® 11. Align the top edge of the customer-supplied custom panel 1. With a TORX screwdriver, remove three screws from both with the top of the console. sides of door; hold the outer panel up while removing the screws. 12. Drill two 3/32" pilot holes 1/2" (13 mm) deep, into the customer-supplied custom panel, through the holes in the top corners on the inner panel, as shown. inner panel align top edges 3 screws drill through outer panel these holes 2. Gently set outer panel aside. 13. Install the
ملخص المحتوى في الصفحة رقم 15
4. Push the plastic buttons out of the side of the tub. Choose attachment option NOTE: Save the buttons to cover the holes after dishwasher is installed. WARNING plastic Excessive Weight Hazard button Use two or more people to move and install dishwasher. Failure to do so can result in back or other injury. Using two or more people, stand the dishwasher up. 5. Push bracket into slot on the side of dishwasher, and bend tab in towards the side of the dishwasher so that it Option 1: Countertop kee
ملخص المحتوى في الصفحة رقم 16
3. Close and latch the door, and place level against the Move dishwasher into cabinet opening front panel. Check that dishwasher is plumb. If needed, adjust leveling leg or add shims under rear wheel until dishwasher is plumb. WARNING Excessive Weight Hazard Use two or more people to move and install dishwasher. Failure to do so can result in back or other injury. 1. Grasp the sides of the dishwasher at the edges of the door panel. 2. Tilt dishwasher backwards on wheels and move dishwasher cl
ملخص المحتوى في الصفحة رقم 17
3. Connect the wires as follows using twist-on connectors Option 2: Power supply cord method sized to connect direct wire to 16-gauge dishwasher wire: WARNING Power supply wire: Terminal box wire: white white black black ground wire ground connector Electrical Shock Hazard WARNING Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, Electrical Shock Hazard fire, or electri
ملخص المحتوى في الصفحة رقم 18
Connect to drain Secure dishwasher in cabinet opening 1. To help minimize vibration, route drain hose to avoid contact with motor, door springs, water line, cabinet, WARNING flooring or the edge of the hole where it passes through the cabinet. 2. Do not remove drain loop from side of dishwasher. drain loop Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. 1. If you have not already done so, open dishwas
ملخص المحتوى في الصفحة رقم 19
3. Hold the two panels together and push them up against Bottom sound pad installation (on some models) dishwasher leg and vinyl pad. 4. Reinstall the screws through the holes in the access 1. Remove the bottom sound pad from inside the panel and the slots in the lower panel. Install right side dishwasher and take it out of the plastic bag. screw first. 2. Place pad on the floor in front of the dishwasher, making sure lettering is facing up and vinyl pad faces down. 3. Fold up and hold the sid
ملخص المحتوى في الصفحة رقم 20
Check operation 1. Read the Use and Care Guide that came with your dishwasher. 2. Check that all parts have been installed and no steps were skipped. 3. Check that you have all the tools you used. 4. Start dishwasher and allow it to complete the shortest wash cycle. After the first two minutes, unlatch door, wait five seconds, then open door. 5. Check to see that there is water in the bottom of the dishwasher tub. Check that dishwasher is working properly. 6. If not, disconnect power or unplu
