ملخص المحتوى في الصفحة رقم 1
Installation instructions
DD605 and DS605 models
DishDrawer
NZ AU GB IE
ملخص المحتوى في الصفحة رقم 2
Safety and warnings WARNING! Electrical hazard Before installing the DishDrawer® , remove the house fuse or open the circuit breaker. If permanently connecting the DishDrawer®, be sure the power is isolated and the DishDrawer® unplugged. This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-gro
ملخص المحتوى في الصفحة رقم 3
1 Contents DOUBLE MODELS Product and cabinetry dimensions 2 Installation Cavity preparation 4 Route the hoses and move into the cavity 5 Removing the tub and levelling the product 6 Securing the product and refitting the tub 7 Plumbing and drainage - OPTION 1 8 Plumbing and drainage - OPTION 1 (connection) 9 Plumbing and drainage - OPTION 2 10 Plumbing and drainage - OPTION 2 (connection) 11 Fitting the toekick 12 SINGLE MODELS Product and cabinetry dimensions 14
ملخص المحتوى في الصفحة رقم 4
Integrated DD605 Prefi nished Flat door DD605 Prefi nished LCD DD605 2 Product dimensions Installation diagrams for illustration purposes only C B N D P I G K H E C L G N O I A F M J Product dimensions (mm) 819.5 - 879.5 819.5 - 879.5 819.5 - 879.5 A overall height* of product 595 595 595 B overall width of product overall depth of product (excl. curvature/handle) 570 570 570 C D depth of drawer (open) (excl. curvature/handle) 520 520 520 809 809 809 E height* of chassis 60 60 60 F height ran
ملخص المحتوى في الصفحة رقم 5
Integrated DD605 Prefi nished Flat door DD605 Prefi nished LCD DD605 3 Cabinetry dimensions Installation diagrams for illustration purposes only B D A C E Cabinetry dimensions (mm) 820 - 882.5 820 - 882.5 820 - 882.5 A inside height of cavity 600 600 600 B inside width of cavity inside depth of cavity (inside) 580 580 580 C D height of adjacent cabinetry 720 720 720 70 - 120 70 - 120 70 - 120 E height of kickstrip Minimum clearances (mm) 2.5 mm 2.5 mm 13 mm DOUBLE MODELS
ملخص المحتوى في الصفحة رقم 6
4 Cavity preparation Parts supplied Drain hose Drain hose Wire clip (2) Clamp (1) Install Phillips Moisture Prefinished toe kick (1) support (1) joiner (1) tabs (2) 16 mm protection White or Black screws (9) tape (1) Hexagonal sockets (2) (to prevent moisture (Long & Short) damage) If the Drain hose(s) supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hose(s) by 3.6m. The kit is available from the nearest Fisher
ملخص المحتوى في الصفحة رقم 7
5 Route the hoses and move into the cavity 1a 1b 2 1 Tie together to avoid kinking 2 If top two tabs are being used, ensure they’re securely 2 fitted before sliding product into cavity. optional optional 3 3 1 Loosen feet first, but do not fully extend until product is in cavity. 1 Ensure hoses and cord are not kinked or twisted. DOUBLE MODELS
ملخص المحتوى في الصفحة رقم 8
6 Removing the tub and levelling the product 3 4 1 Ensure the tub is removed and then rotated counter-clockwise to prevent kinked hoses. 2 5 30 mm 3 5 4 Ensure product is level. Using the most appropriate length Hexagonal socket supplied, and a screwdriver, fully extend levelling feet up to required distance. Hexagonal socket 1 2 3 4 5 x 4 DOUBLE MODELS
ملخص المحتوى في الصفحة رقم 9
7 Securing the product and refi tting the tub 5 The mounting tabs are in pairs, one on C C each side of the optional product. At least two sets of tab pairs must be used. A and B tab pairs OR B and C tab pairs or all three pairs. Ensure the sound insulation is repositioned correctly. BB A A 6 Ensure the tub clips on 3 both sides are reset. 5 Before refitting the tub, ensure the hoses are not twisted and the latches at 4 the rear of each drawer runner are facing forward. 4 Ensure
ملخص المحتوى في الصفحة رقم 10
8 Plumbing and drainage - OPTION 1 DishDrawer® and Standpipe Ø38 mm Waste disposal (optional) Do not connect to DishDrawer® Waste Water Waste supply (COLD) Valve min. R200 mm Max. distance of Left hand Right hand hoses and cord from side side chassis edge Drain hose 2011 mm 1794 mm Left hand Right hand Inlet hose 1561 mm 1344 mm side side Power cord 1776 mm 1559 mm Water Pressure Max Min Water softener models 1 MPa (145 psi) 0.1 MPa (14.5 psi) Other models 1 MPa (145 psi)
ملخص المحتوى في الصفحة رقم 11
9 Plumbing and drainage - OPTION 1 (connection) DishDrawer® and Standpipe Ø38 mm 7 If space is limited for fixing, push hose through drain hose support to required height 1 750- max. 882.5 120 mm mm 38 mm 2 8 1 Fit supplied o washer 180 2 3 4 DOUBLE MODELS
ملخص المحتوى في الصفحة رقم 12
10 Plumbing and drainage - OPTION 2 DishDrawer® using sink trap with drain hose joiner Supplied drain hose joiner HIGHLOOP min. 150 mm Waste Water supply (COLD) Valve min. R200 mm DOUBLE MODELS 750 - 882.5 mm
ملخص المحتوى في الصفحة رقم 13
11 Plumbing and drainage - OPTION 2 (connection) DishDrawer® using sink trap with drain hose joiner If space is limited 7 for fixing, push hose through drain hose support to required height 1 750- 882.5 mm 2 3 8 1 Ensure hoses are routed straight to joiner. Remove Fit supplied excess hose material if o washer 180 necessary. 2 3 4 DOUBLE MODELS
ملخص المحتوى في الصفحة رقم 14
12 Fitting the toekick 9 1 2 3 10 4 5 6 7 19 8 9 Important! D o not overtighten screw. 10 DOUBLE MODELS
ملخص المحتوى في الصفحة رقم 15
13
ملخص المحتوى في الصفحة رقم 16
Integrated DS605 Prefi nished Flat door DS605 Prefi nished LCD DS605 14 Product dimensions Installation diagrams for illustration purposes only B C K D L H F I E G A J C F K H Product dimensions (mm) A overall height* of product 409 409 409 overall width of product 595 595 595 B 570 570 570** C overall depth of product (excl. curvature/handle) 520 520 520 D depth of drawer (open) (excl. curvature/handle) E height* of chassis 409 409 409 depth of chassis 552 552 552 F 18 18 18 G depth of drawe
ملخص المحتوى في الصفحة رقم 17
Integrated DS605 Prefi nished Flat door DS605 Prefi nished LCD DS605 15 Cabinetry dimensions Installation diagrams for illustration purposes only B D A C Cabinetry dimensions (mm) A inside height of cavity 412 412 412 inside width of cavity 600 600 600 B 580 580 580 C inside depth of cavity (inside) D clearance below benchtop Minimum 3* Minimum 3* Minimum 3* * Clearance is measured from the underside of benchtop to the chassis Minimum clearances (mm) 2.5 mm 2.5 mm 13 mm SINGLE MODELS
ملخص المحتوى في الصفحة رقم 18
16 Cavity preparation Cavity Drain hose Drain hose Wire clip (1) Clamp (1) Phillips 16 mm Moisture protection tape (1) support (1) joiner (1) screws (5) (to prevent moisture damage) If the Drain hose(s) supplied are not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hose(s) by 3.6m. The kit is available from the nearest Fisher & Paykel Authorized Service Agent or www.fisherpaykel.com. DO NOT extend beyond this limit. o 90 Moist
ملخص المحتوى في الصفحة رقم 19
17 Route the hoses and move into the cavity 1a 1b 2 Tie together to avoid kinking 1 2 2 2 1 1 Ensure hoses and cord are not kinked or twisted. SINGLE MODELS
ملخص المحتوى في الصفحة رقم 20
18 Removing the tub and securing the product 3 1 4 Ensure the tub is removed and then rotated counter-clockwise 2 to prevent kinked hoses. 5 30 mm 3 5 4 The mounting tabs are in pairs, one on each side of the product. Ensure the sound insulation is repositioned correctly. SINGLE MODELS
