ملخص المحتوى في الصفحة رقم 1
GE Model 19200
www.jascoproducts.com
Wireless Portable Chime
Installation Instructions for Wireless Portable
Door Chime Kit
Required Tools: Small flat blade screwdriver, drill, drill bit, and phillips
screwdriver.
Included Hardware:
(2) 3x20mm screws
(2) Double sided adhesive pads
The portable wireless door chime Kit has two components:
Portable Chime (receiver) Push
ملخص المحتوى في الصفحة رقم 2
Battery Release Tab 2. Install 4 C-cell batteries (we recommend Alkaline Batteries) 3. Remove back of wireless push button and install the 12-volt battery (included) as shown below. Chime Tune Setting All wireless chimes may have more than one push button. The chime tune for each push button is set with jumpers 7-9. Single Push Button Kit: If you purchased a kit with a single push button, the chime tune will be set to Ding Dong from the factory. Dual Push Button
ملخص المحتوى في الصفحة رقم 3
and 9=off.) 3. Select the desired chime sound from the table below. Chime Sound Table Position 7 8 9 Westminster ON OFF OFF Ding Dong OFF ON OFF Knock OFF OFF ON Bronze Chime ON ON OFF Cuckoo Clock ON OFF ON Foghorn OFF ON ON Gong ON ON ON ON: Add a jumper to a location OFF: Remove jumper from a location. 4. Remove or add the jumpers to match the table. 5. Store unused jumpers as shown. Parking the jumper
ملخص المحتوى في الصفحة رقم 4
Each component has jumpers for setting the house security code: The chime and pushbutton must be set to the same house security code for the combination to operate together. Note: The push button has 3 additional jumpers that are used to set the chime tune that will play. The chime tune jumpers do not affect the house security code. 1. Remove power or batteries from the chime. 2. To remove the batteries from the pushbutton, open the pushbutton case as shown below.
ملخص المحتوى في الصفحة رقم 5
3. Locate the House Security Code door and screw located on the back of the AC Chime. Remove the screw and take off the door. 4. Locate the chime and pushbutton jumpers shown below. Push Button Jumpers Chime Jumpers in battery compartment 5. Jumpers 1-6 are used to select 1 of 64 possible home security codes. 6. To change the house code, add or remove jumpers as needed. It is recommended to change only one jumper at a time and then tes
ملخص المحتوى في الصفحة رقم 6
b. Replacing the back cover 1. Push buttons are typically mounted at the same height as the door knob or handle (between 36" and 44" above the floor). 2. Before mounting, choose a mounting location that is not farther than 150 feet from the chime unit location.
ملخص المحتوى في الصفحة رقم 7
Not farther than 150 feet 3. Place the push button where you would like to mount it and with the chime as close to its final position as possible and test operation. If it works, mount the button. If it does not work, see TROUBLESHOOTING. 4. Use back cover of push button as a template to mark two screw holes. 5. Drill two holes with 3/32” size drill in marked locations. 6. Secure back cover to the mounting surface with two supplied mounting screws.
ملخص المحتوى في الصفحة رقم 8
7. Press front housing onto back cover. 8. Test operation. If the chime does not work, see TROUBLESHOOTING. Operation 1. Slide power switch to “High” or “Low” to power the chime. 2. Gently press transmitter button to sound chime. Troubleshooting Chime doesn't work: 1. Make sure push button switch is depressed and held for at least 1 second. 2. Make sure plastic tag is removed from battery. 3. Make sure house code switches 1-6 on chime and push button match exactly. 4.
ملخص المحتوى في الصفحة رقم 9
For technical support contact Jasco Products Company at 1-800-654-8483 or www.jascoproducts.com Made in China is a trademark of General Electric Company and is used under license to Jasco Products Company LLC, 311 N.W. 122nd Street, Oklahoma City, OK 73114. www.jascoproducts.com Rev. 1-07 19200
