ملخص المحتوى في الصفحة رقم 1
MorningLinc
®
INSTEON Morning Industry RF Doorknob/Deadbolt
Controller
Model : 2458A1
ملخص المحتوى في الصفحة رقم 2
MorningLinc Owner’s Manual MorningLinc Owner’s Manual TABLE OF CONTENTS ABOUT MORNINGLINC ............................................................................................................................... 2 Key MorningLinc Features......................................................................................................................... 3 What is Included with MorningLinc ......................................................................................
ملخص المحتوى في الصفحة رقم 3
MorningLinc Owner’s Manual Key MorningLinc Features • Installs and links in minutes • Locks or unlocks up to 15 Morning Industry RF deadbolts and door locks at the press of a button • Links individual commands to On and Off buttons on INSTEON controllers • Indicates INSTEON setup mode activity and operational states with a Status LED and beeper • Stores setup state in non-volatile memory so settings aren’t lost during power outages • Two-year warranty What is Included wit
ملخص المحتوى في الصفحة رقم 4
MorningLinc Owner’s Manual Installing MorningLinc When installing MorningLinc, it is recommended to use an outlet or extension cord to keep the unit within five feet of the door lock fixture. Once installation is complete, MorningLinc can be moved to another outlet (up to 30 feet away from the door lock fixture). MorningLinc can be used to control up to 15 Morning Industry deadbolts and door locks. However, each door lock must be within 30 feet of MorningLinc. 1) Plug MorningLinc in
ملخص المحتوى في الصفحة رقم 5
MorningLinc Owner’s Manual USING MORNINGLINC Tap MorningLinc’s Set button to toggle the door lock fixture locked and unlocked. The MorningLinc Status LED will turn on solid if the door is locked or turn off if the door is unlocked. NOTE: The MorningLinc Status LED will follow the last INSTEON command it received. When the door is manually locked/unlocked from the keypad or lock itself, the Status LED will not change until it receives an INSTEON command (either from a linked controlle
ملخص المحتوى في الصفحة رقم 6
MorningLinc Owner’s Manual The MorningLinc Status LED will flash once and then turn on if the door is locked or turn off if the door is unlocked. 5) Confirm that linking was successful by locking/unlocking the door and tapping the Off button you just linked to on the controller. MorningLinc will respond appropriately. Unlinking MorningLinc from an INSTEON Controller If you are going to discontinue using MorningLinc, it is very important that you unlink it from any linked controller
ملخص المحتوى في الصفحة رقم 7
MorningLinc Owner’s Manual ADDITIONAL RESOURCES Find home automation solutions, helpful tips, interactive demos, videos, user forums, and more at the Smarthome Learning Center: www.smarthome.com/learningcenter.html TROUBLESHOOTING Problem Possible Cause Solution The Status LED on MorningLinc is not MorningLinc may not be Be sure MorningLinc is not plugged into a switched turning on and getting power. outlet that is turned off. MorningLinc won’t control the load. MorningLinc M
ملخص المحتوى في الصفحة رقم 8
MorningLinc Owner’s Manual SPECIFICATIONS, CERTIFICATION, AND WARRANTY Specifications View specifications for MorningLinc at: www.smarthome.com/2458A1.html Certification This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third- party testing laboratory. The North American ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U.S. and Canadian device safety standards, that
ملخص المحتوى في الصفحة رقم 9
MorningLinc Owner’s Manual address below, postage prepaid, with proof of the date of purchase and an explanation of the defect or error. The repair, replacement, or refund that is provided for above shall be the full extent of Seller’s liability with respect to this product. For repair or replacement during the warranty period, call the INSTEON Gold Support Line at 800-762-7845 with the Model # and Revision # of the device to receive an RMA# and send the product, along with all other req
