Stanton Professional Valve DJ Mixer VRM-10 دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

VRM-10
Professional Valve DJ mixer
OWNER’S M A N U A L

ملخص المحتوى في الصفحة رقم 2

INPUTS AND OUTPUTS (Rear) Aside from the headphone output and microphone jacks, The volume can be set to 0dBu maximum and is controlled all connections are on the rear of the VRM10. in each channel individually with the AUX (25) control knob. The signal for the auxiliary send is taken after the GAIN sig- A Mains plug with fuse and voltage selector. nal path, but before the EQ section (please also see the Changing the fuse: The lid for the housing of both fuses can block diagram). easily be opene

ملخص المحتوى في الصفحة رقم 3

U BOOTH NOTE: To achieve the optimum sound performance and The output value of the BOOTH is set at 0dBu. It can be lowest signal-to-noise ratio it is essential in the digital out- adjusted via the control knob BOOTH (49) put section to set the output impedance of the mixer to the highest possible level (control 52) and if necessary to lower NOTE : BOOTH output is not affected by any balance/pan the volume of the digital equipment connected to the setting (50). VRM10 receiving signal. The main ou

ملخص المحتوى في الصفحة رقم 4

MICROPHONE CHANNEL the level for the preamplification of the microphones. 3 DJ MIC 2 9 TREBLE 4 DJ MIC 1 10 MIDDLE Both mic inputs can be used as symmetrical or non- sym- 11 BASS metrical (balanced or non-balanced) channels with either The 3 band EQ adjusts the equalization level for both XLR or 1/4” jacks, with the provided combo connectors microphone inputs. THE XLR jack are set as follows: 12 VOLUME 1 GND The volume control adjusts the equalization level for both 2 +SIGNAL microphone inputs.

ملخص المحتوى في الصفحة رقم 5

effect individually. The middle position of this control will 27 BASS have the value of the individual selected effect preset indi- 28 MIDDLE cated in the diagram above. 29 MID FREQ With the EQ you can set the level of each frequency. 18 DEPTH Furthermore the EQ can be used to isolate certain frequen- With this control you can adjust the intensity of the LFO cies. This is very easy and effective with the high quality and very strong filter-type parametric EQ on your VRM10. 19 SELECT With this sw

ملخص المحتوى في الصفحة رقم 6

35/36 CROSSFADE LED’s 45 TUBE INDICATOR (MAGIC EYES) The LED’s located left and right of the crossfader indicate, Both indicator tubes for the left and the right channel will which input channel lies on which side of the crossfader indicate the output volume of the mixer, except the according to the crossfader assign switch (22). MIC channels. When the tube lines meet in the middle you have the ideal output peak. Additionally, the maximum peak 37 CROSSFADE CURVE will be indicated by the mast

ملخص المحتوى في الصفحة رقم 7

Ohm. You will hear the master signal in your headphones if (off), the master signal is set to post-filter. you haven’t selected any of these options: PFL (31), EFFECT (57) and FILTER (56). 57 EFFECT By pressing the EFFECT switch you can pre-listen to the 56 FILTER internal effect signal. When the FILTER switch (56) is selected, you will hear the mixed master signal before the activated DJ filter or NOTE : The PFL and EFFECT monitor switches must be off master effect. When the FILTER switch is i

ملخص المحتوى في الصفحة رقم 8

BLOCK DIAGRAM