ملخص المحتوى في الصفحة رقم 1
OPERATORS MANUAL MP 44
DJ MIXER
MAIN MIC AUX MIC CH 1 CH 2 CH 3 CH 4 MASTER AUX IN
0 0 0 0
4 6 4 6 4 6
OL OL OL OL
2 8 2 8 2 8
LEFT / CUE
-20 -10 -7 -4 -2 0 +2 +4 +7 +10 dB
0 10 0 10 OFF +6 -12 +12 OFF +6 -12 +12 OFF +6 -12 +12 OFF +6 -12 +12 0 10
LEVEL LEVEL HI LEVEL HI LEVEL HI LEVEL HI LEVEL RIGHT / PGM AUX A
OL OL
1A 2A 3A 4A 4 6
1B 2B 3B 4B LEFT / RIGHT
SOURCE SOURCE SOURCE SOURCE 2 8
PEAK PROGRAM METER
CUE / PGM
-8 +8 -8 +8 OFF +6 OFF +6 OFF +6 OFF +6 0 10
HI HI MID MID MID MID
AUX B
EQ EQ
ملخص المحتوى في الصفحة رقم 2
INPUT CHANNELS MP 44 INPUT CH’s 1A, 2A, 3A, and 4A are stereo, TO MADE IN U.S.A. PHONO GROUND NO RANE CORP. NO IN unbalanced RCA jacks that operate as RIAA equalized Phono Inputs or Line Inputs. INPUTS CH 4 CH 3 CH 2 CH 1 PHONO switches set the mode for Inputs 1A, 2A, BA B A B A B A 3A, and 4A. In the out position, these Inputs operate at L L L L line-level (max input +20 dBu). Press the switch in for PHONO PHONO PHONO PHONO R R R R PHONO operation. If a turntable is not connected to one of thes
ملخص المحتوى في الصفحة رقم 3
FlexFX™ FlexFX™ switches independently assign any combination of the four Input Channels to the FlexFX Loop for external processing. FlexFX assignment is totally independent of A – POST – B mix assignment. You’ll get more out FlexFX of your favorite external effects box than you ever thought possible, and experiment with this feature for a long time to come. The indicator illuminates when FlexFX is active on it's Channel. FlexFX SEND jacks are unbalanced ¼" Tip/Sleeve Outputs. The maximum output
ملخص المحتوى في الصفحة رقم 4
AUXILIARY INPUTS & OUTPUTS Maximum Input and Output signal levels on the AUX jacks is +20 dBu. AUX IN A is a line-level, unbalanced Input on stereo RCA jacks. AUX IN A is summed with AUX OUT AUX IN B A B A the 4 Channel Input mix. AUX IN A applications include any unbalanced auxiliary input such as L L ADAT, VCR, DVD, Video camera, computer audio card, etc. R R AUX IN B is a line-level, balanced Input on two ¼" TRS jacks. AUX IN B is summed with the 4 Channel Input mix. AUX IN B is ideal for use
ملخص المحتوى في الصفحة رقم 5
The LIMIT threshold control sets the maximum allowable MASTER signal level. The Limiter affects both House and Booth signals. This control is located on the rear panel and screw driver adjust to prevent tampering. L Threshold range is –20 dBu to +20 dBu. Center detent is 0 dBu. LIMIT threshold indicators are located on the front LIMIT and rear panels. R Only 6 dB of post limiter makeup gain is available. To set the maximum system level, adjust the Limiter with HOUSE and BOOTH LEVEL controls set
ملخص المحتوى في الصفحة رقم 6
PAGING The HOUSE PAGE INPUT provides a means to automatically interrupt all program material, and broadcast emergency messages at a preset level. The HOUSE PAGE INPUT jack is a balanced 3-pin Euroblock. The Input is line-level with a maximum signal level of +20 dB. When an input signal greater than –20 dBu is sensed, HOUSE and BOOTH levels HOUSE PAGE GAIN INPUT automatically attenuate 40 dB and the HOUSE PAGE INPUT signal routes to both HOUSE and BOOTH Outputs. The HOUSE PAGE INPUT GAIN is set i
ملخص المحتوى في الصفحة رقم 7
POWER The IEC appliance input jack is connected to AC mains using a line cord appropriate for N108 your area. The high efficiency switching power supply used in the MP 44 operates at voltages from 85 VAC to 250 VAC, 50 or 60 Hz. To prevent accidental shutoff during the height of the FOR CONTINUED GROUNDING PROTECTION DO NOT REMOVE show, there is no front panel power switch. When applying power to the system, remember to SCREW turn power amplfiers on last. POWER 100-240V 50/60 Hz 20 WATTS WAR
ملخص المحتوى في الصفحة رقم 8
Install the knob so that the line on the knob is properly aligned with the silk-screening on the front panel of the remote. Install any Decora plate of your choice. For a secured installation, you may wish to leave the knobs off and use a blank Decora plate to cover the remote after adjustment. WIRE TYPES Variations in wire type do not greatly affect the perfor- mance of the remote controls. However, 22-gauge stranded wire with a flexible jacket is recommended. You may use 5- conductor unshielde
