ملخص المحتوى في الصفحة رقم 1
OPERATING INSTRUCTIONS
CONTENTS
Setup & Installation 2
Platter Setup
3
Cartridge Setup 4
Interchanging Tonearm Tubes 5
Tone Arm Setup
6
Controls 7
Cable Setup 10
Specifications
11
Trouble Shooting 12
ملخص المحتوى في الصفحة رقم 2
SETUP & INSTALLATION This turntable has been designed exclusively for DJ use and can be setup in a variety of different ways depending on your mixing style. The turntable should rest on a level and stable surface that is clear of obstructions. If a mixer is placed between two turntables make sure that there is at least ¼" (7mm) between the mixer and the turntables to prevent damage to the turntables and to reduce unwanted system noise. Mixer Mixer 85
ملخص المحتوى في الصفحة رقم 3
PLATTER SETUP WARNING: Incorrect Platter setup can lead to poor turntable performance, platter instability, or permanent motor damage. 1. Start by inspecting the bottom of the aluminum platter to check that both locking pins have rubber fittings on them. 2. Next, rotate the top of the motor assembly (brass in color) so that two holes are aligned parallel with the front of the turntable. 3. Install the platter onto the center spindle and motor assembly making sure that the
ملخص المحتوى في الصفحة رقم 4
CARTRIDGE SETUP For Head Shell Mounted Cartridges: The cartridge that comes with this turntable should be preinstalled on the head shell. If it isn't, please follow the below instructions for installing a cartridge onto the head shell. 1. Position the head shell and the cartridge so that the four connector pins are visible. Make sure that the stylus cover is installed to prevent damage to the stylus during installation. 2. Prepare to connect the cartridge to the head shell usin
ملخص المحتوى في الصفحة رقم 5
INTERCHANGING TONEARM TUBES (sold seperately) WARNING: An incomplete understanding of this procedure could lead to permanent damage to the headshell, your records, or the tonearm assembly. NOTICE: Interchanging tonearm tubes unnecessarily may shorten the life of the tonearm tubes and/or tonearm components. This turntable features the world's only tonearm assembly capable of accommodating two different tonearm tube styles: S-Shaped and Straight. The S-Shaped tube produces a higher sig
ملخص المحتوى في الصفحة رقم 6
TONE ARM SETUP A properly adjusted tone arm and cartridge setup will minimize vinyl record wear and optimize the performance of the turntable. Follow these simple steps for setting the tone arm on the turntable: NOTE: In most cases, when using the S-Shaped tonearm tube, the additional S-Weight must be fastened to the tonearm to achieve proper stylus pressure.Balancing the Tone Arm 1. Begin the balancing process by lifting the cue lever to the up position (or make sure that the stylus
ملخص المحتوى في الصفحة رقم 7
CONTROLS General Controls 1. Power Button Pushing this button down turns on the turntable. It illuminates red when the turntable is switched on. 2. Start/Stop Buttons These buttons start and stop the turntable motor. Both buttons have the same function. 3. Platter This turntable has a special edge design that has been optimized for "dragged" platter slow downs. 4. Reverse Button Pushing this button down reverses the rotation direction of the turntable platter. 5. Pitch Slid
ملخص المحتوى في الصفحة رقم 8
CONTROLS continued Tone Arm Parts 10 11 10. Counterweight and Scale Ring and S-Weight The Counterweight is used to balance the head shell and cartridge assembly so that the proper amount of stylus pressure is applied to the record. The S-Weight (sold seperately with S-arm tube) should be used in most cases 12 when the S-Shaped tube is used. It is fastened to the tonearm by threading it into the rear weight balance shaft. The S-weight can be stored below the counterweight in the
ملخص المحتوى في الصفحة رقم 9
CONTROLS continued Bottom Parts 18. Adjustable Rubber Dampening Feet When all of the feet of the turntable are completely tightened, the top flat surface of the turntable will be at 85mm. Unscrewing these feet raises the turntable up to compensate for unleveled surfaces. 19. Carrying Handles These handles provide a secure grip so that the turntable may be comfortably transported. 20. Voltage Selector This switch allows you to adjust your equipment to be compatible with your count
ملخص المحتوى في الصفحة رقم 10
CABLE SETUP This turntable is shipped with two sets of special cables: (1) Right Angle IEC Power Cord (1) Right Angle RCA cord w/ground wire NOTE: Before connecting any cables, make sure that the voltage selector switch is set to the proper setting! Making the power and audio connections: 1. Begin by lifting the turntable up from the rear handle and resting it on its side. (NOTE: The turntable must be supported because it is not stable in this position!) 2. First, using the
ملخص المحتوى في الصفحة رقم 11
SPECIFICATIONS Turntable Section: Tonearm Section: Type: 3 speed, fully manual Type: Locking collar based interchangeable tube system Motor: Direct Drive- 8 Pole, 3 Phase Diecast Aluminum 3-bearing construction Starting Torque: 1.6 kg/cm Height Range: 0-6 mm Start Time: 0-33.33 RPM in 0.8 sec Cue System: Dampened Lift Lever, Braking System: Electronic Servo Brake Arm Rest and Arm Clip Platter: Aluminum Diecast Weight: 18 lbs (8.2 kg) Speeds:
ملخص المحتوى في الصفحة رقم 12
Problem Cause? Solution Turntable does not turn on. Disconnected Power Cord? Connect Power Cord. The sound level is very low. The Turntable is not connected to a Connect the device to a preamp DJ device with a PHONO preamp. mixer or an AV receiver that has an input labeled PHONO, not AUX or LINE. The sound is on one side only. The Cartridge is not properly wired. Reconnect the wires from the headshell to the cartridge. See the "Cartridge Setup" section for more detail. The
ملخص المحتوى في الصفحة رقم 13
INSIDE THE BOX: (1) TT-200 w/Straight (1) Aluminum Platter (1) Slipmat Tonearm (1) Counter Weight (1) Headshell (1) 2.5 Gram Headshell (1) 45 RPM Adapter Weight (1) Service Tool (1) IEC Power Cable (1) RCA Cord w/ Ground Wire TT-200 Manual /English, R3.1 Copyright Numark Industries, LLC 2003
