ملخص المحتوى في الصفحة رقم 1
VERTI PRO II™ Set Up
Unpacking: Thank you for purchasing the VERTI PRO II™ by Ameri-
American DJ®
can DJ®. Every VERTI PRO II™ has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the ship-
ping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fi xture for any
damage and be sure all accessories necessary to operate the unit have
arrived intact. In the event damage has been f
ملخص المحتوى في الصفحة رقم 2
VERTI PRO II™ Contents VERTI PRO II™ Safety Precautions Introduction..........................................................................2 This unit may blow a fuse if the maximum allotted load of 10 amps Features................................................................................3 (220v = 5 amps) is reached. If the fuse needs replacement, always replace the fuse with same exact type that was remove. Use of a Safety Precautions.....................
ملخص المحتوى في الصفحة رقم 3
VERTI PRO II™ Operation VERTI PRO II™ Operation ™ Operating Modes: You can operate the VERTI PRO II in three dip-switch settings. different modes: 3. The optional VertiPro/C Blackout Controller may be used in this Stand-Alone mode (Usually for single unit operation) - The unit operation mode to control a blackout function. will react to sound, chasing through the several built in programs. 4. After the unit settings have been set and are plugged in, adjust
ملخص المحتوى في الصفحة رقم 4
VERTI PRO II™ Operation VERTI PRO II™ Set Up be placed anywhere in a DMX line, at the beginning, at the end, or Typical DMX Linking: anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain. DMX Indicate DMX Indicate DMX Indicate 1 1 1 Dip-switches in DMX mode: This unit uses dip switches to assign a 4 2 4 2 2 4 8 8 8 16 16 16 64 32 64 32 64
ملخص المحتوى في الصفحة رقم 5
VERTI PRO II™ Set Up VERTI PRO II™ Set Up dard two conductor shielded cable (This cable may be purchased at 3-Pin XLR to 5-Pin XLR Conversion almost all pro sound and lighting stores). Your cables should be made Conductor 3-Pin XLR Female (Out) 5-Pin XLR Male (In) with a male and female XLR connector on either end of the cable. Also Ground/Shield Pin 1 Pin 1 remember that DMX cable must be daisy chained and can not be split. Data Compliment (- signal) Pin 2 Pin 2 Notice: Be sur
ملخص المحتوى في الصفحة رقم 6
VERTI PRO II™ Fuse & Lamp Replacement VERTI PRO II™ Trouble Shooting Caution: Always replace with the exact same type lamp and fuse, Trouble Shooting: unless otherwise specified by an authorized American DJ® technician. Listed below are a few common problems that you may encounter, Replacing with anything other than the specified part can damage the with solutions. unit and will void the manufactures warranty. No light output from the unit; 1. Be sure you have connected your
ملخص المحتوى في الصفحة رقم 7
VERTI PRO II™ DMX Traits VERTI PRO II™ DMX Dip Switch Chart This chart list the DMX dip switch setting for DMX address 1 through The VERTI PRO II™ is a single DMX channel fixture 511. Follow the instructions below to configure fixture dip switches with 127 129 your desired DMX address. 01 128 255 DMX Address Quick Reference Chart DIP SWITCHES Dip Switch Position Stop #9 XXXXXX XXOOO OO O O O DMX DIP Switch Settings CW Fast CW Slow CCW Slow CCW Fast #8XX XX XOO OOO OX XX O O X = O
ملخص المحتوى في الصفحة رقم 8
VERTI PRO II™ Warranty MODEL: VERTI PRO II™ 1-YEAR LIMITED WARRANTY SPECIFICATIONS: A. American DJ® hereby warrants, to the original purchaser, American DJ® products to be free of manufacturing defects in material and workmanship for a period of 1 Year (365 days) VOLTAGE: 120V~60Hz / 220V~50Hz from the date of purchase. This warranty shall be valid only if the product is purchased LAMP: ZB-64514 120v/300w or within the United States of America, including possessions and territories.
