ملخص المحتوى في الصفحة رقم 1
Assembly Instructions for Model: WFA37
Thank you for choosing Sanus Systems Woodbrook Furniture. The Woodbrook Furniture is
constructed of real hardwood and resonance dampening MDF.
Safety Warning: If you do not understand these directions, or have any doubts about the
safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or
www.sanus.com. Check carefully to make sure that there are no missing or defective parts. Our
customer service representatives
ملخص المحتوى في الصفحة رقم 2
Parts List (Cont) (1) Bottom Shelf - q (3) Mid Shelf - r (1) Wood Panel - w (1) Left Side Panel - s (1) Right Side Panel - t (1) Back Panel - u (1) Door - v Step 1: Prepare the Side Panels Thread a Cam Pin (a) into each of the smaller holes in the Side Panels (s,t). Tighten each Cam Pin with a Phillips screw driver. Insert a Dowel (d) into the larger adjacent hole in the Side Panels. See Diagram 1 for assistance. Detai
ملخص المحتوى في الصفحة رقم 3
Step 2: Prepare Stretchers Add a Cam (b) to each Front Stretcher (o) and Back Stretcher (p). Make sure the arrow in each Cam faces the hole on the side of the Stretchers. See Diagram 2 for assistance. Diagram 2 Detailed View o a arrow p Step 3: Add Stretchers Add the Front and Back Stretchers (o,p) to the Side Panel (s), by aligning the Cam Pin (a) with the hole which the Cams (b) point to and the Dowel (d) goes in
ملخص المحتوى في الصفحة رقم 4
Step 4: Add Side Panel Press fit the Side Panel (t) against the Stretchers (o,p) so the Cam Pin (a) goes into the hole which the Cams (b) point to. The Dowel (d) fits into the adjacent hole. Tighten each Cam in a clockwise motion until the Stretchers are secured. Note: Make sure the hinge holes on the Side Panel are on the same side as the Front Stretchers. Diagram 4 Detailed View p b o t
ملخص المحتوى في الصفحة رقم 5
Step 6: Add Top Gently tap a Dowel Pin (c) into the holes on the top of each Side Panel (s,t). Slide a Spacer (g) over each Dowel Pin. Press fit the Top (n) so it fits onto the Dowel Pins. See Diagram 6 for assistance. Diagram 6 Detailed View n c g s t t
ملخص المحتوى في الصفحة رقم 6
Step 8: Add Hinge Assembly to Door Insert a Hinge Screw (j) through the Hinge (l) and thread it into the Door (v). Tighten each with a Phillips screw driver. Repeat process until both Hinge Assemblies are secured. Diagram 8 Detailed View v m j l Step 9: Door Install Position the Door (v) so the holes in the Hinge Plate (m) line up with the front p
ملخص المحتوى في الصفحة رقم 7
Step 10: Add Mid Shelves Thread a Shelf Pin (e) into the desired location in the Side Panels (s,t). For each shelf, four Shelf Pins will be required. Insert each Mid Shelf (r) into the assembly and press fit onto the Shelf Pins. Make sure the wood strip on each shelf is facing toward the front. See Dia- gram 10 for assistance. Note: Diagram 10 is a Back View. Diagram 10 Detailed View s r t
ملخص المحتوى في الصفحة رقم 8
Step 12: Hinge Adjustment for small Door Each hinge Assembly is adjustable in multiple directions. See Diagram 12 for assistance. Diagram 12 Side Adjustment Depth Adjustment Height Adjustment Sanus Systems 2221 Hwy 36 West, St. Paul, MN 55113 12.28.05 Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
