ملخص المحتوى في الصفحة رقم 1
AF/WB Mode
Mode Quick-Release
Illuminator
Ikelite SLR-DC Housing Drive Mode
Dial Strobe
Meter/Flash
Lid Snap
Mount
Main Dial
i n s t r u c t i o n m a n u a l
AE/FL
Lock
#6871.05 for Canon EOS 5D
Zoom
Control
Port Lock
Gear Sleeve
Drive Gear Lens
Shutter
Release
Release
Rubber
Handle
Port
Lid Opening
Snap
Strobe
Mount
Aluminum Tray
FRONT VIEW
Viewfinder Port
AE/FE Lock
Zoom
Quick
Release
Button
I
A
H
B
G
Congratulations on your purchase of an Ikelite Digital Camera Shutter
C
Lens
Release
F
Hous
ملخص المحتوى في الصفحة رقم 2
F Fl la as sh h C Co on nn ne ec ct ti io on n f fo or r E Ex xt te er rn na al l S St tr ro ob be es s C Cl lo os si in ng g t th he e H Ho ou us si in ng g housing back When using an external strobe connect the housings Hot Shoe 1. Place housing face down in your Connector, slide the connector into the hot shoe of the camera lap. from the back of the camera as shown. Slide the connector 2. Check to see that there is an o’ring forward until on the housing back and that it is it stops. This clea
ملخص المحتوى في الصفحة رقم 3
Type 2 Installation: Figure 1 I In ns st ta al ll l t th he e G Ge ea ar r S Sl le ee ev ve e I In ns st ta al ll li in ng g t th he e Z Zo oo om m C Cl la am mp p & & G Ge ea ar r S Sl le ee ev ve e O On n T Ty yp pe e 2 2 L Le en ns se es s After the Zoom Clamp is installed, lower the appropriate Gear Due to the larger diameter of lens opening on Type 2 lenses, the Sleeve over the Zoom Clamp aligning the Gear Sleeve ribs with the Zoom Clamp and Gear Sleeve need to be installed from the rear g
ملخص المحتوى في الصفحة رقم 4
I In ns st ta al ll li in ng g t th he e P Po or rt t c co on nt t. . U Us si in ng g E Ex xt te er rn na al l S St tr ro ob be es s This housing has Conversion Circuitry built into the camera T To o R Re em mo ov ve e P Po or rt t tray. When used with Ikelite DS Substrobes the Conversion Circuitry provides real Canon eTTL flash exposure with over and To remove the port lift up on each Release Button and slide the under-exposure compensation of two f-stops in half-stop port lock away from the po
ملخص المحتوى في الصفحة رقم 5
D DS S2 20 00 0 S Su ub bs st tr ro ob be es s S St tr ro ob be e A Ar rm ms s • DS200 SubStrobes with a Serial Number 6,499 or below require This housing offers two types of arm mounting systems. The an update to operate with the eTTL Conversion Circuitry. top of the rubber handles utilize Ikelite’s Quick-Release Arm, • DS200 Substrobes with a Serial Number of 6,500 or higher or available with the SA-100R Arm system. with one of the two following labels in the battery compartment The bottom o
ملخص المحتوى في الصفحة رقم 6
L Le en ns s & & P Po or rt t R Re ec co om mm me en nd da at ti io on ns s P Po or rt ts s C Co on nt ti in nu ue ed d C Ca an no on n L Le en ns se es s. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .D Do om me e. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .F Fl la at t P Po or rt t . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .F Fl la at t P Po or rt t w w/ /F Fo oc cu us s FLAT PORT 14mm EF 1:2.8 ..
ملخص المحتوى في الصفحة رقم 7
3. Some of the controls have a short shaft and cannot be pulled G Ge en ne er ra al l T Ti ip ps s out exposing the shaft for lubrication. In the unlikely event one 1. You should completely assemble and test your set-up in a of these controls sticks or becomes difficult to operate you can swimming pool before using it in openwater. remove the control from the housing and lubricate it, or return the housing to Ikelite for maintenance. To remove the control, 2. It is a good idea to start each phot
