ملخص المحتوى في الصفحة رقم 1
Manual for Camera Housing - Model DSC-F707 / 717 (Sony)
User Manual
Contents: 1. Introduction
2. Specification
3. Set up Instructions
4. Use & Care of Housing
5. Service
6. Warranty
1. Introduction
10 BAR Underwater Housings are small, light and rugged enough to be used on
every dive. Use of a clear polycarbonate allows for visual inspection of camera
condition and the O-ring seal. 10 BAR Housings are designed for the ever-
i
ملخص المحتوى في الصفحة رقم 2
2. Specification Test Pressure 10 Bar (300 ft.) Housings are individually tested Closure Design Air Lock Body Material Polycarbonate Overall Size 188 x 125 x 172 mm Total Weight Approximately 1.1 Kg (Housing only) Buoyancy (with camera) Approximately neutral in salt water Additional Features Visible main O-ring for final pre-dive check Double O-ring design on all controls Combined handle/accessory arm bracket Accessories Spare main O-ring (included) Universal tool (included) Silico
ملخص المحتوى في الصفحة رقم 3
3. Set up Instructions 3.1 Pressure release plug: The body and lid are designed with a “no clip” closure arrangement. Testing has shown that this arrangement allow the water to exert an even pressure on the O -ring, increasing the reliability of the watertight seal. To open the housing, the pressure release plug must be first unscrewed and then pulled out all the way. This provides a passage for the air to pass though and eliminate the pressure different between the inside of the housin
ملخص المحتوى في الصفحة رقم 4
3.3 Special note on responsibility for watertight integrity: Each housing is individually inspected and hydrostatically tested in the factory. The design of the piston O-ring seal is among the most reliable in the industry and the watertight integrity is excellent. This special O-ring design provides a perfect seal even if there is any movement between the body and lid due to change of ambient pressure. However please note that responsibility for ensuring the integrity of the watertight sea
ملخص المحتوى في الصفحة رقم 5
that no contamination such as dust, hair, salt, etc. has fallen onto the O-ring or O-ring recess, as a precaution we recommend maintaining the O-ring every time the lid is opened. Procedure: • Place the lid on a firm non-slip level surface. • The O-ring can be extracted using an O-ring extractor tool (make sure the tool has no sharp edges). Alternatively use the flats of the thumbs to gently stretch the O-ring on two faces (as shown) thus making a small loop protruding a few mm. The
ملخص المحتوى في الصفحة رقم 6
Replace the lid. Remember to ensure the pressure release plug is pulled all the way out while closing, otherwise the air cannot escape. Squeeze the lid closed all the way, you will hear the hiss of air being expelled. Screw home the pressure release plug. There is no need to excessively tighten this plug. The seal is made by internal O-rings. The O-ring on the underside of the plug is just to keep out dirt. After replacing the lid, make a final visual inspection of the main O-ring f
ملخص المحتوى في الصفحة رقم 7
salt deposits that may have built up. No chemical cleaners should be used. Mild detergents e.g. shampoo and soap based cleaners are permitted. Important, Polycarbonate may be harmed by some household chemicals, the housing should never be exposed to the following classes of chemicals: benzene, toluene, xylene, chlorinated hydrocarbons, methanol, any other solvents, strong acids and bases. For long term storage please remove the main body to lid O-ring. Transportation. When tran
ملخص المحتوى في الصفحة رقم 8
6. Warranty The warranty is valid within two years from the date of first purchase. The warranty applies only to the housing itself. 10 BAR does not accept any liability either implicit or otherwise for any equipment housed inside, or used together with the housing. In the event of the housing flooding within the period of warranty, 10 BAR will repair or replace the housing. Please note that disassembly of the housing will invalidate warranty. Please fill in the information below, and r
ملخص المحتوى في الصفحة رقم 9
(Copy to be returned to 10 Bar Underwater Housings) The warranty is valid within two years from the date of first purchase. The warranty applies only to the housing itself. 10 BAR does not accept any liability either implicit or otherwise for any equipment housed inside, or used together with the housing. In the event of the housing flooding within the period of warranty, 10 BAR will repair or replace the housing. Please note that disassembly of the housing will invalidate warranty. Plea
