ملخص المحتوى في الصفحة رقم 1
OWNER'S MANUAL
24CM AC/DC REMOTE COLOUR TELEVISION
MODEL: 2418
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL:(02)9313 7111
FAX:(02)9313 7555
www.palsonic.com.au
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA:1300 657 888
ملخص المحتوى في الصفحة رقم 2
This equipment has been designed and manufactured to meet the highest international standards, but, like any electrical apparatus which is operated at mains voltage, care must be taken if you are to obtain the best results and safety is to be assured. This is particularly important with audio and TV equipment. DO read this handbook carefully and keep it handy for ready reference. DO ensure that all electrical connections (including the mains plug, extension leads and interconnections between pie
ملخص المحتوى في الصفحة رقم 3
ANTENNA ANT. PLUG ANT IN DEGAUSSING SWITCH DC IN VIDEO IN EARPHONE JACK AUDIO IN IR RECEIVER CONTROL BOARD AUDIO OUT FUSE INDICATOR SKIP CH AUTO CH PSET VOL FT VOL FT MUTE STAND BY CHANNEL SELECTOR CALL CHANNEL SELECTOR ( ) PREVIOUS VOLUME CONTROL ( ) TIME SLEEP TIMER PICTURE PICTURE/TIME ( ) 2
ملخص المحتوى في الصفحة رقم 4
* Take care not to drop, dampen, disas- INSTALLING BATTERIES : semble the Remote Control Unit. 1. Remove the battery cover of Remote * Operatable remote control range is Control Unit. limited as shown. 2. Insert two "AAA" 1.5V batteries making sure the polarity (+ or -) of the batteries matches the polarity marks inside the unit. 3. Close the battery cover. * When the Remote Control Unit is not used for a long time or the batteries are worn out, take out the batteries to prevent electrolyte
ملخص المحتوى في الصفحة رقم 5
. DC POWER SUPPLY: 1. Be sure the DC power supply is 12V- 14V, attach the plug of DC power cord to the DC socket on the back of the cabinet. The set will be in stand by mode, the power indicator is red. If this television is being used in a mobile installation, attach the small connector of the supplied Car Battery Cord to the DC 12V jack on the rear of the set, and the power indicator lighted. 2.3 same as AC POWER SUPPLY. ATTENTION : 1. Unplug the power cord when you are not watching the set: 2
ملخص المحتوى في الصفحة رقم 6
6 15 CHANNEL PRESET . AUTO PRESET 1. Press the PSET (PRESET ON/OFF) button on the front panel. The current band and channel position will be displayed on screen (in green). 2. Press AUTO (AUTO PRESET) button, the appliance will search the signal of TV station in the order of VHFL, VHFH and UHF, as shown in the following, and memorise them from channel number 1 position. VHFH VHFL UHF * During presetting, the green block turns into yellow. The moving red block indicates the change of
ملخص المحتوى في الصفحة رقم 7
SKIP BUTTON: . FUNCTION: When CHANNEL SELECTOR button is used to select channels, the channel will be skipped if they are set to "SKIP" mode. For example: Set 2~7 channels to "SKIP" mode, the procedure of channel position increasing or decreasing. 8 CHANNEL INCREASE CH 0 1 2 58 59 CH CH CHANNEL DECREASE 0 1 2 58 59 (THE APPLIANCE) (REMOTE) . OPERATION: 1. Press PSET (PRESET ON/OFF) button to set preset mode. 2. Select a channel by using CHAN
ملخص المحتوى في الصفحة رقم 8
PICTURE CONTROL (REMOTE CONTROL UNIT) . Press the PICTURE CONTROL button on the Remote Control Unit. The FUNCTION to be adjusted is selected in sequence as shown in the following chart at every press of the button. BRIGHTNESS CONTRAST PICTURE COLOUR . Adjust the button to obtain satisfactory picture. ON SCREEN DISPLAY Red Block Moves CAPTION FUNCTION DISPLAY Press button Press button Contrast CONTRAST Strong Weak Brightness BRIGHTNESS Dark Light Colour COLOUR Pale Deep CALL
ملخص المحتوى في الصفحة رقم 9
SLEEP BUTTON (REMOTE CONTROL UNIT) . Using SLEEP button allows you to have the appliance automatically turned off a predetermined time, and set the appliance to stand by mode. Press SLEEP again SLEEP 0 SLEEP 90 (RED) (GREEN) Decrease 10 minutes at every press SLEEP 10 (GREEN) . After the SLEEP function is set, the remaining time will be automatically displayed for 4 seconds every ten minutes. * If you press STAND BY button while the SLEEP function is operating, the SLEEP function will be can
ملخص المحتوى في الصفحة رقم 10
4. Use CALL button to display the present time on screen. See "CALL" operation * In case of power failure, the clock operation will be cancelled. . ON TIME OPERATION: 1. Set the CLOCK in operation mode. 2. Press the TIMER button until "ON TIME" displays on the screen. 3. Press the button to select the exact hour when you want to turn on the appliance. Press the button to select the exact minute when you want to turn on the appliance. 4. Press the CHANNEL SELECTOR to set your desi
ملخص المحتوى في الصفحة رقم 11
The set supplys a munual degaussing function. Push the DEGAUSS button on the back of the cabinet, then loosen it, repeat this action for serveral times. The set can be desgaussed thoroughly. External degaussing is necessary if the munual degaussing ineffective. NOTE: The interval between every press action should be more than 10 second, otherwise it will be magnetization. the upper comer of the screen for 4 seconds. Press AV/TV button again to return TV mode, the original channel will be display
ملخص المحتوى في الصفحة رقم 12
TROUBLE SHOOTING GUIDE Many apparent malfunctions may be caused by slight misadjustment of regular controls or some other equally similar simple causes. If any problem arises in the operation of your set, first check through this list of symptoms and correction. Should the problem be unsettled, unplug the set and contact your dealer. Symptoms Check these things Try these adjustment . . Press POWER BUTTON Be sure power cord is plugged No picture, . in. Try another channel. no sound. . . Press AV
ملخص المحتوى في الصفحة رقم 13
SPECIFICATIONS : TV System : PAL/BG Power Supply : DC 12V Channel Coverage : VHFL 2-4; VHFG 5-12; UHF 28-61 Cable channel : S1-S2 CRT : 25cm Audio output : 0.7W Max. Antenna Impedance : VHF/CATV/UHF 75 ohm Dimension (W x H x D) : 265 x 235 x 305 (mm) Weight : 4.8 kg AC power adapter : AC 240V, 50Hz Power input : DC 12V/4A Power output : 154 x 118 x 56 (mm) Dimension (W x H x D) : 0.5 kg Weight : 1pc Car Battery Cord Remote Control Unit Power Supply : DC 3V (2 x AAA) * Design and specifications
ملخص المحتوى في الصفحة رقم 14
PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www.palsonic.com.au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 604-10203-01
