ملخص المحتوى في الصفحة رقم 1
™
PLATINUM SERIES II
Natural Gas Barbecues
Step-By-Step Guide
Platinum Series II
2200 NG
Platinum Series II
3400 NG
Platinum Series II
3200 NG
CANADIAN GAS ASSOCIATION
®
A P P R O V E D
R
NOTICE TO INSTALLER: These instructions
WARNING: Do not operate this barbecue
must be left with the owner and the owner
without reading the entire operating guide.
should keep them for future use.
THIS GAS APPLIANCE IS DESIGNED FOR
FOR YOUR SAFETY
OUTDOOR USE ONLY.
If you smell gas:
1. Shut off gas to the appli
ملخص المحتوى في الصفحة رقم 2
Typical natural gas supply installation. Figure 1. INSTALL GAS SUPPLY General Specifications for Piping Note - Contact your local municipality for building codes regulating outdoor gas barbecue installations. In absence of Local Codes, you must conform to the latest edition of ANSI Z223.1. WE RECOMMEND THAT THIS INSTALLATION BE DONE BY A PROFESSIONAL. Some of the following are general requirements taken from ANSI Z223.1, for gas supply installations. Refer to ANSI Z223.1 latest edition for compl
ملخص المحتوى في الصفحة رقم 3
TOOLS NEEDED REMOVE BOTTOM TRAY Phillips screwdriver FROM GRILL Remove bottom rack from top of packaging. Remove all tape from packaging. Remove outer box. Pull out bottom tray from cooking box. Remove packaging material from 7/16 inch or adjustable wrench bottom tray, catch pan holder, catch pan, and drip pan. For the Platinum Series II 3400, remove the white plastic from the stainless steel. SUPPLIES NEEDED You will need a soap and water solution to check for gas leaks. (See section “Check for
ملخص المحتوى في الصفحة رقم 4
REMOVE GRILL FROM REMOVE PACKAGED LOWER PACKAGING PARTS FROM LOWER Make sure natural gas hose is free from lower packaging CARTON before lifting. Left work surface WARNING: Lifting the barbecue from the lower packaging requires at least two people. With two people lift straight up and over lower packaging and cardboard support. Note: For the Platinum Series II 3400, make sure the front doors are securely closed before lifting. Right work surface (Platinum Series II 2200 NG only) Side burner (Pla
ملخص المحتوى في الصفحة رقم 5
INSTALLATION OF CATCH REINSTALLATION OF PAN INTO BOTTOM TRAY STAINLESS STEEL Hook the ends of the catch pan holder into the hole in the FLAVORIZER BARS bottom tray. Figure 4. The front of the catch pan holder Note: Remove any tape or packing material. Parts are must be on the same side as the finger grip of the shipped in place. Use these steps to check that they are bottom tray. in position. The Flavorizer bars are already in place. This step is only for reinstallation. Set the long stainless s
ملخص المحتوى في الصفحة رقم 6
REINSTALLATION OF REINSTALLATION OF COOKING GRATES WARMING RACK Note: The cooking grates are already in place. This Set the warming rack into the slots at the rear of the stepp is for reinstallation only. cooking box. Figure 8. Set the cooking grates onto the ledges in the cooking box. The open "U" of the cooking grate goes down. Figure 7. Figure 8 Figure 7 6
ملخص المحتوى في الصفحة رقم 7
If you have the Platinum Series II INSTALL WARM-UP 2200, go to step “Install Work BASKET Surfaces” on page 8. Insert one end of the Warm-Up Basket into the hole in the right end of the lid and the other end into the slot in the left end of the lid. Figure 9. If you have the Platinum Series II 3200, go to step “Install Work Surface and Side Burner” on page 8. If you have the Platinum Series II 3400, go to step “Install Work Surface and Side Burner” on page 10. Figure 9 7
ملخص المحتوى في الصفحة رقم 8
INSTALL WORK INSTALL WORK SURFACE SURFACES AND SIDE BURNER FOR THE PLATINUM SERIES II 2200 FOR THE PLATINUM SERIES II 3200 You will need... left work surface, side burner assembly, You will need...left work surface, right work surface, four four 1/4-20 x 1/2 inch bolts, four nylon washers and a 1/4-20 x 1/2 inch bolts, four nylon washers and a 7/16 7/16 inch or adjustable wrench. inch or adjustable wrench. Insert the left work surface tabs in the slots to the left of Insert the left work surface
ملخص المحتوى في الصفحة رقم 9
Check that the side burner is properly assembled. INSTALL WORK SURFACE (c) AND SIDE BURNER Windshield Burner FOR THE PLATINUM SERIES II 3200 cap (CONTINUED) Route the side burner hose around the tank panel so it will not interfere with the scale indicator rod. The side burner hose is connected in the following manner: Slide back the collar of the quick disconnect on the Burner (b) manifold. Push the male fitting of the side burner hose ring into the quick disconnect, and maintain pressure. Slide
ملخص المحتوى في الصفحة رقم 10
INSTALL WORK SURFACE (a) (c) Tabs AND SIDE BURNER FOR THE PLATINUM SERIES II 3400 You will need... left work surface, side burner assembly, four 1/4-20 x 1/2 inch bolts, four nylon washers and a 7/16 inch or adjustable wrench. Insert the left work surface tabs in the slots to the left of the cooking box. Figure 16 (a). Slip washers on the bolts View from and insert the bolts as shown. Tighten. Figure 16 (b). left side View from right side To install side burner Note: Remove protective covers fro
ملخص المحتوى في الصفحة رقم 11
Check that the side burner is properly assembled. INSTALL WORK SURFACE AND SIDE BURNER Windshield (c) FOR THE PLATINUM SERIES II 3400 Burner cap (CONTINUED) Route the side burner hose so it will not interfere with the scale indicator rod. The side burner hose is connected in the following manner: Slide back the collar of the quick disconnect on the Burner (b) manifold. Push the male fitting of the side burner hose ring into the quick disconnect, and maintain pressure. Slide Grate Lugs the collar
ملخص المحتوى في الصفحة رقم 12
INSTALL BOTTOM RACK CHECK THAT ALL Place the bottom rack between the frame supports. BURNER VALVES ARE OFF Figure 21. Valves are shipped in the OFF position, but you should check to be sure. Put the knob on each valve. Check by pushing down and turning clockwise. Figure 22. Figure 21 Figure 22 For the Platinum Series II 3400, place the bottom rack under the cart between the frame supports. Lift up one end of the rack so that it clears the crosspiece. Continue to lift until the opposite end clear
ملخص المحتوى في الصفحة رقم 13
CHECK FOR GAS LEAKS DANGER Do not use an open flame to check for WARNING gas leaks. Be sure there are no sparks or This gas connections of your Weber Gas open flames in the area while you check for Barbecue have been factory tested. We do leaks. This will result in a fire or explosion however recommend that you leak check all which can cause serious bodily injury or gas connections before operating your death and damage to property. Weber Gas Barbecue. WARNING: You should check for gas leaks eve
ملخص المحتوى في الصفحة رقم 14
CHECK FOR GAS LEAKS (b) WARNING: Do not ignite burners while checking for leaks. Check for leaks by wetting the connections with the soap (c) and water solution and watching for bubbles. If bubbles (a) form or if a bubble grows there is a leak. Check: a) Hose to manifold connection. Figure 26 (a). WARNING: If there is a leak at connection a, retighten the fitting with a wrench and recheck for leaks with soap and water solution. (d) If a leak persists after retightening the fitting, turn OFF the
ملخص المحتوى في الصفحة رقم 15
REINSTALL THE CONTROL PANEL Set the control panel in place over both frame braces. (Hold the Crossover Ignition button up while setting the control panel in place.) Slip washers on Phillips screws, insert into holes as shown, and tighten. Figure 27 (a). Push on the burner control knobs. Figure 27 (b). (b) (a) Underside view Figure 27 of right work surface or side burner REFER TO OPERATING GUIDE BEFORE LIGHTING BARBECUE
ملخص المحتوى في الصفحة رقم 16
