ملخص المحتوى في الصفحة رقم 1
Contents
Important Safety Instructions . . . . . . . . . . . . . . . 2
Battery Safety Precautions . . . . . . . . . . . . . . 4
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Included with the XC600/700 SERIES . . . . . . . . 6
Important Electrical Considerations . . . . . . . . . . 7
Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Telephone Line Problems . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 2
Important Safety Instructions When using your telephone equipment, these basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning, and use a dry cloth, without liquid or aerosol cleaners. 4. Do not use this product near water; for example, near a bath tub, wash bowl, kitch
ملخص المحتوى في الصفحة رقم 3
11. To reduce the risk of electric shock, do not disassemble this product. Take it to qualified service personnel when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used. 12. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power supply cord is damaged or frayed
ملخص المحتوى في الصفحة رقم 4
Battery Safety Precautions Caution: To reduce the risk of fire or injury to persons by the battery, read and follow these instructions: 1. Use only the appropriate type and size Battery Pack specified in this Operating Guide. 2. Do not dispose of the Battery Pack in a fire. The cell may explode. Check the Nickel-Cadmium Battery Disposal package insert for disposal instructions. 3. Do not open or mutilate the Battery Pack. Released electrolyte is corrosive and may cause damage to the eyes or skin
ملخص المحتوى في الصفحة رقم 5
Introduction Congratulations on your purchase of the Uniden XC600/700 SERIES Cordless Telephone. These phones are designed to exacting standards which provide reliability, long life, and outstanding performance. This series of phones is available in designer colors which are designated by different model numbers. Accordingly, this manual describes the operation of the XC610, XC611, XC615, XC714, XC716, XC717, and the XC718. Features • 25 46/49 MHz Channels • AutoSecure™ • Random Code™ Digital •
ملخص المحتوى في الصفحة رقم 6
Now is the time for all good men to come to the aid of the Now is the time for party. all good Four men score to yeas ago come to the aid of our the fathers party. Four set forth a new score yeas ago nation our fathers conceived set in Liberty and dedicated to the forth a new nation conceived in Liberty and dedicated proposition to that the all men proposition that are created equal. The quick all men are created equal.brown The quick foxbrown jumped fox over the jumped over the garden garde
ملخص المحتوى في الصفحة رقم 7
Important Electrical Considerations Unplug all electrical appliances when you know an electrical storm is approaching. Lightning can pass through your household wiring and damage any device connected to it. This phone is no exception. Warning: Please do not attempt to unplug any appliance during an electrical storm. Caution: Changes or modifications to this product not expressly approved by Uniden, or operation of this product in any way other than as detailed by this Operating Guide, could void
ملخص المحتوى في الصفحة رقم 8
Radio Interference Radio interference may occasionally cause buzzing and humming in your cordless Handset, or clicking noises in the Base Unit. This interference is caused by external sources such as TV, refrigerator, vacuum cleaner, fluorescent lighting, or electrical storm. Your unit is NOT DEFECTIVE. If these noises continue and are too distracting, please check around your home to see what appliances may be causing the problem. In addition, we recommend that the Base not be plugged into a ci
ملخص المحتوى في الصفحة رقم 9
Installation Selecting a Location Before choosing a location for your new phone, there are some important guidelines you should consider: • The location should be close to both a phone jack and continuous power outlet. Note: A continuous power outlet is an AC outlet which does not have a switch to interrupt its power. • Keep the Base Unit and Handset away from sources of electrical noise such as motors or fluorescent lighting. • Be sure there is sufficient space to fully extend the Base Unit ant
ملخص المحتوى في الصفحة رقم 10
Telephone Line Outlets There are two types of phone outlets: Modular Jack Most phone equipment available now uses modular jacks. Phone cords are fitted with a molded plastic connector which plugs into this type of jack. If you do not have modular phone jacks, contact your local telephone company for information about their installation. Hard-wired Jack Some equipment is wired directly to a phone jack, and these types of installations require a modular jack converter. This type of installation is
ملخص المحتوى في الصفحة رقم 11
AC ADAPTOR DC IN 9V PULSE–TONE TEL LINE + – Applying Power to the Base Unit All the XC600/700 SERIES phones require an AC outlet, without a switch to interrupt power, and the included AC adapter. To relieve strain on the DC plug when the phone is placed on a desk or table, connect the adapter as shown below. Wrap the power cord around the convenient notch on the bottom. Important: Place the power cord so that it does not create a trip hazard, or where it could become chafed and create a fire or
ملخص المحتوى في الصفحة رقم 12
AC ADAPTOR DC IN 9V PULSE–TONE TEL LINE + – Desk or Tabletop Installation 1. Place the Base on a desk or tabletop. 2. Plug the AC Adapter cord into the 9V DC input jack on the Base Unit. 3. Place the AC Adapter cord around the strain relief. 4. Plug one end of the long telephone cord into the TEL LINE jack on the Base Unit. 12
ملخص المحتوى في الصفحة رقم 13
5. Plug the other end of the cord into the telephone jack on the wall. 6. Plug the AC Adapter into a standard 120V AC wall outlet. Note: Do not use an outlet controlled by a wall switch. Use only the Uniden AC Adapter supplied with this phone. 13
ملخص المحتوى في الصفحة رقم 14
Wall Installation Standard Wall Plate Mounting These phones are designed to be mounted on a standard AT&T or GTE wall plate. 1. Plug the AC Adapter into the Base Unit. 2. Place the AC Adapter cord inside the molded channel. 3. Plug one end of the short telephone cord into the TEL LINE jack on the Base Unit. 14
ملخص المحتوى في الصفحة رقم 15
4. Place the telephone cord inside the molded channel on the bottom of the Base Unit. Then plug the other end of the telephone cord into the modular jack on the wall. 5. Place the Base Unit on the posts of the wall plate and push down until it’s firmly seated. 6. Plug the AC Adapter into a standard 120V AC wall outlet. Note: Do not use an outlet controlled by a wall switch. 15
ملخص المحتوى في الصفحة رقم 16
Direct Wall Mounting If you do not have a standard wall plate, you can mount your phone directly on a wall. Before mounting your phone, consider the following: • Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. • Make sure the wall material is capable of supporting the weight of the Base Unit and Handset. • Use #10 screws with anchoring devices suitable for the wall material where the
ملخص المحتوى في الصفحة رقم 17
3. Place the AC Adapter cord inside the molded channel. 4. Plug one end of the long telephone cord into the TEL LINE jack on the Base Unit. 5. Place the cord inside the molded channel on the bottom of the Base Unit. 6. Place the Base Unit on the screws and push down until it’s firmly seated. 17
ملخص المحتوى في الصفحة رقم 18
7. Plug the other end of the telephone line cord into the wall jack. 8. Plug the AC Adapter into a standard 120V AC wall outlet. Note: Do not use an outlet controlled by a wall switch. Setting the Handset Retainer The handset retainer holds the Handset in place if your phone is mounted on a wall. The steps below describe how to remove and replace the retainer so that the tab faces up. 1. Push up on the Handset retainer on the Base Unit, and slide the tab out. 18
ملخص المحتوى في الصفحة رقم 19
2. Flip the retainer over so the tab faces up. 3. Put the retainer back into its slot on the Base Unit. 4. Push down on the Handset retainer until it snaps into place. 19
ملخص المحتوى في الصفحة رقم 20
SettingUpYourPhone Extending the Antenna Before using your phone, be sure to raise its antenna to the vertical position. Installing the Handset Battery Pack charge 1. Press in on the Battery Cover Release. 2. Slide the battery compartment cover down. 20
