Summary of the content on the page No. 1
Summary of the content on the page No. 2
Copyright © by Edimax Technology Co, LTD. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company. This company makes no representations or warranties, either expressed or implied, with respect to the contents
Summary of the content on the page No. 3
Table of Contents 1. Introduction .......................................................................... 1 Features ............................................................................... 1 Package Contents................................................................ 1 System Requirements.......................................................... 1 2. Installation ............................................................................ 2 Hardware Connection ............
Summary of the content on the page No. 4
1. Introduction It is a combination 10/100M Ethernet adapter and integrated standard-based 3-port USB hub all in one easy to use device. As a fully integrated USB solution, the new USB/Ethernet adapter allows users to easily connect to the Ethernet network with a complete out of the box, Plug-N-Play solution. Features Complies with IEEE 802.3/802.3u standards Complies with USB 2.0 and backward compatible with USB1.1 with data rates 1.5/12/480 Mbps Built in 3 ports USB2.0 hub Sup
Summary of the content on the page No. 5
2. Installation Hardware Connection General instructions for installing the USB 2.0 3 Port Hub with Ethernet Adapter are provided below. Since the design of system may vary, refer to your system’s reference manual for further information, if needed. 2
Summary of the content on the page No. 6
Driver Installation On Windows 2000/XP/Server 2003/Vista 1. With your computer switched on, insert the “USB2.0 to Fast Ethernet Adapter with 3-Port USB Hub” into an available USB2.0 port of your computer. The following message will appear on your screen, Please click ‘Cancel’ and use the wizard to install driver. 3
Summary of the content on the page No. 7
2. Please insert the installation CD into your CDROM drive. The Autorun setup programs should run under Windows 2000/XP/Server 2003/Vista, or you can click on the “Browse CD” to find other OS drivers in the CD. 3. Connect the Ethernet adapter’s USB end to a free USB port of your computer. Then a pop-up message will appear in the notification area indicating the installation is complete. 4
Summary of the content on the page No. 8
*Actual strings depend on your operation system. These screen shots are from Windows Vista and might vary slightly for each operation system. Now the installation is complete. You can connect the adapter to a network device by an Ethernet cable: 1. Connect an Ethernet cable to the Ethernet port on the adapter. 2. Connect the other end of the Ethernet cable to your network hub, switch or router. The Link LED should light up green to indicate a proper physical connection betwe
Summary of the content on the page No. 9
On MAC OS X 10.3/10.4 1. Insert the provided driver CD into your CD-ROM drive. Double-click the CD and navigate to the directory of \Drivers\Mac10.x.\ AX88772.pkg 2. When the Install AX88772 USB CDC Drivers screen appears, please select Continue. 3. When the screen below appears, please choose the volume that you want to install and click Continue. 6
Summary of the content on the page No. 10
4. When the screen below appears, please click Upgrade to perform the software. 5. Please enter your password as prompted. 6. Please select Continue Installation to install the software when the screen below prompted. 7
Summary of the content on the page No. 11
7. Please click Restart to reboot the Mac. 8. Connect the Ethernet adapter to a free USB port. 9. Start System Preferences and select Network, you’ll see the screen as below prompted and please select OK. 10. You will find that a new Ethernet network interface is available. It’s usually named Ethernet Adapter (en1) or Ethernet Adapter (en2).11. 8
Summary of the content on the page No. 12
*Actual strings depend on your operation system. These screen shots are from MAC OS X 10.4 and might vary slightly for each operation system. Now the installation is complete. You can connect the adapter to a network device by an Ethernet cable: 1. Connect an Ethernet cable to the Ethernet port on the adapter. 2. Connect the other end of the Ethernet cable to your network hub, switch or router. The Link LED should light up green to indicate a proper physical connection between th
Summary of the content on the page No. 13
Verifying the Driver Installation On windows 2000/XP/Server 2003/Vista Once you finish the installation, you can open Windows Device Manager to verify if your Ethernet adapter is properly installed. To access the Device Manager: On Windows Vista: Right-click Computer on the desktop and click Properties > Device Manager. On Windows 2000/2003/XP: Right-click My Computer on the desktop and click Properties > (Hardware) > Device Manager. In the Network adapters group, an item named A
Summary of the content on the page No. 14
On MAC OS X 10.3/10.4 Once you finish the installation, you can open GO > Utilities > System Profile > Hardward > USB > to verify if your Ethernet adapter is properly installed. In the USB High-Speed Bus group, an item named ASIXx72A should be displayed. 11
Summary of the content on the page No. 15
3. Specifications Upstream port x 1 (USB Type A plug) Downstream port x 3 (USB Type A receptacles) USB Compliance : USB1.1 & USB 2.0 RJ-45 x 1 (Ethernet 10BASE-T/Fast Ethernet 100Base-TX port) LAN Complies with the Full-duplex with flow control and Half-duplex with backpressure operation Power Supply Input : 100~240v 50Hz-60Hz Output: 5V 2.5A Blue LED for Power-on indication LED Green LED for Ethernet Connection indication Size (Lx W x H) : 98 x 36 x
Summary of the content on the page No. 16
4. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
Summary of the content on the page No. 17
14
