Summary of the content on the page No. 1
SM-CDM1039
CD/MP3-RECEIVER CD/MP3-
Instruction manual
Summary of the content on the page No. 2
Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents.................................................................................................................................2 Important safeguards.....................................................................................
Summary of the content on the page No. 3
Important safeguards - Read carefully through this manual to familiarize yourself with this high-quality sound system. - Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. - When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit. - DO NOT attempt to disassemble the unit. Laser beams from the optical pickup are dangerous to the eyes. - Make sure that pins
Summary of the content on the page No. 4
Installation/ Connections First complete the electrical connections, and then check them for correctness. Installation way It is an anti-theft installation way. The chassis wear a metal sliding housing. Please have the wiring connection of the power supply, speakers and antenna as for the requirement of the manual, and then install the metal sliding housing into the car according to the diagram. 4
Summary of the content on the page No. 5
Din rear-mount (method 2) Installation using the screw holes at both sides of the unit. 1. Select a position where the screw holes of the main unit are fitted for aligned, and tighten the screws at 2 positions at each sides. Use either truss screws (5 x 8mm) or flush surface screws (4 x 8mm), depending on the shape of the screw holes in the bracket. 2. Screw 3. Factory radio mounting bracket. 4. Dashboard or Console 5. Hook (Remove this parts) Note: The mounting box, outer trim ring, and the Hal
Summary of the content on the page No. 6
Connection scheme Notes: - In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the distortion during high volume level. - Prohibit to make the conductors of auto antenna and ground touch with each other. 6
Summary of the content on the page No. 7
Panel controls Front panel 1. OPEN BUTTON Press it to remove the front panel. 2. TA BUTTON Press it to active the TA function. 3. SCAN BUTTON 4. PTY / CLK BUTTON Press it to active the PTY function. Press and hold it to set the time. 5. PRESET STATION [1-6] BUTTONS 6. No 1/ PLAY/PAUSE (4;) button 7. No 2/ INT BUTTON 8. No 3/ RPT Press it to play the current tack repeatedly. 7
Summary of the content on the page No. 8
9. No 4/ RDM Press to start the random playback. 10. No 5/ DN 10 Press it to start playing on 10 tracks back. 11. No 6/ UP 10 Press it to start playing on 10 tracks forward. 12. BAND / SUB BUTTON In radio mode press it to select desired band. Use this button to turn the Subwoofer output ON. 13. POWER BUTTON 14. AUX IN 15. F / PS BUTTON 16. USB socket 17. SD socket 18. MUTE BUTTON Press it to switch the sound off. 19. VOL KNOB / SEL BUTTON Rotate it clockwise to increase the volume level; rotate
Summary of the content on the page No. 9
Inner panel Press the OPEN button on the front panel to flip it down. 1. LED INDICATOR 2. RESET BUTTON 3. DISK SLOT 9
Summary of the content on the page No. 10
Functions of controls General operations Power button Press any button to switch the unit on. The display will show a message WELCOME . Press and hold the POWER button to switch the unit off. The display will show a message GOOD-BYE . Note: After the unit is off, volume level and radio current settings will be memorized, and when you turn the unit on it will resume the stored status you set. Volume control Rotate the VOL knob (VOL knob / SEL button) on the faceplate. The larger the number shown
Summary of the content on the page No. 11
Mute function Press the MUTE button to cancel the sound. Press it again or VOL +/ - to resume. Subwoofer control Press and hold the BAND/ SUB button to turn the Subwoofer output ON. An external amplifier is required to operate a subwoofer. Beep Sound Off function Press the VOLUME knob / SEL until Beep On is displayed. Turn the Volume knob to switch between Beep ON and OFF. Equalizer setting Press the Volume button, until EQ indication is displayed then rotate the Volume knob to choose between
Summary of the content on the page No. 12
Radio operations BAND selection Press the BAND / SUB button repeatedly to select your desired radio band during RADIO mode: FM1, FM2, FM3, AM1, AM2. Each band can store 6 preset stations, for a total of 30 preset memory stations. Tuning In Radio mode turn the TUNE button to manually adjust the radio frequency. Rotate the button for 3 seconds once and radio will seek the next strong and clear frequency station. Repeat to seek more stations in your listening area with a strong signal. Mono/ Stereo
Summary of the content on the page No. 13
RDS function During listening to radio or CD if there are any travel announcements from a nearly local station the radio will always know the frequency of that radio station. Then it will receive the station, turn up the volume or interrupt the playback of the music for the duration of the announcement. At the end of the announcement the radio will return to its previous state ready for the next announcement. Function AF (Alternative frequency) Press the AF button, the unit will choose the stron
Summary of the content on the page No. 14
Function Mask DPI- Mask all · Press the sound select button for 2 seconds. · Press the SEL button to cycle through to Mask DPI . · Rotate the encoder volume to toggle between MASK DPI and MASK ALL mode. · Leave the unit idle for the mode to take effect. During MASK DPI mode the unit will mask only the AF which has different PI, this is the default mode. During MASK ALL mode the unit will mask the AF which has different PI and no RDS signal with high field strength. Retune S / L Short / Long fun
Summary of the content on the page No. 15
CD/ / MP3/ WMA/ USB/ SD card operations Discs for playback This unit can play disc types: CD/CD-R/-RW. Compatible with formats: MP3/WMA. USB/ SD/ MMC notes USB functions (flash memory type) MP3 music play. SD/ MMC card support, 2in1 (SD/ MMC) support. USB flash memory. FAT 12/ FAT 16/ FAT 32 is possible - FAT 12/16 (dir: 200 support, file: 500 support), - FAT 32 (dir: 200 support, file: 500 support). Filename: 32 byte/ Dir name: 32 byte. Tag (id3tag ver2.0) - Title/ Artist/ Album: 32 byte suppor
Summary of the content on the page No. 16
Multi-session CD reading The multi-session reading will be activated automatically if the player detects a file that is written in multi- session format. Inserting the USB/ SD device Remove the cover from the USB port, then insert the USB device into the USB slot on the front panel. Then the playing mode will be changed into USB mode automatically. Or press the MODE button to select USB. The first USB device track playback will start. Pausing playback To ensure good system performance, wait unti
Summary of the content on the page No. 17
Random playback During disc playback, press the No 4 / RDM button to start random playback of the tracks. The display will show RDM / RDM ON (in USB/ SD mode). Press again to cancel. Intro playback You can play the beginning of every track for 10 seconds in sequence. Press the No 2 / INT button to start intro play. The display will show INT . Press again to cancel. ID3 Tag function (for MP3/ WMA modes) If a MP3 file has ID3 Tag information it will be displayed on the LCD. If there is no ID3 Tag
Summary of the content on the page No. 18
After playing all the files sequentially in the first folder, the unit will play sequentially all of the files in the next folder. The unit will continue playing through all of the folders on the USB drive in this manner. In the USB drive has loose files and folders containing files, it will play the loose sequentially, then it will play the files in the folders sequentially. AUX IN · Insert the supplied AUX IN cable s stereo plug into the AUX IN jack on the panel of the unit. · Pres the MODE b
Summary of the content on the page No. 19
MP3 overview Notes on MP3 - MP3 is short for MPEG Audio Layer 3 and refers to an audio compression technology standard. - This product allows playback of MP3 files on CD-ROM, CD-R or CD-RW discs. - The unit can read MP3 files written in the format compliant with ISO 9660. However it does not support the MP3 data written by the method of packet write. - The unit can not read an MP3 file that has a file extension other than .mp3 . - If you play a non- MP3 file that has the .mp3 extension, you may
Summary of the content on the page No. 20
Anti-theft system This unit is equipped with a slide-down detachable and mask panel. Panel can be detached and taken with you, helping to deter theft. Detaching the front panel 1. Press the PWR button to turn the power off. 2. Press the OPEN button on the front panel. 3. Push the panel to the right and then pull it towards you. 4. Place the panel into the case and take it with you when you leave the car. Attaching the control panel 1. Insert left side of the control panel into the main unit. Not
