Summary of the content on the page No. 1
V-037 Easy Guide
UK SERVICE & HELP - VAX CARE 0870 6061248
Mon-Fri. 9.00am to 5.00pm. An answer phone is available out of these hours. If you have queries or concerns about using your VAX, call the HELPLINE. Calls are charged at the UK national rate.
Please make a note of the serial number and model number of your VAX before calling. There are over 400 approved VAX Service Agents in the UK . For your nearest Service Agent please call VAX Care.
Summary of the content on the page No. 2
Parts checklist 1 2 FRONT BACK 13 3 10 4 11 4 2 5 5 12 14 15 6 16 7 8 9 1 Hanging loop 11 Charger 2 Vac on/off button 12 Multi Hard Floor cleaner 3 Vac on/off lock 13 Solution dispensing trigger 4 Mid-handle grip 14 Solution tank release button 5 Cleaning solution tank 15 Charger input 6 Dust canister release button 16 Charging indicator 7 Dust canister 8 Mop head *NOT MEANT FOR USE 9 Vacuum cleaner nozzle WITH WAX BASED FLOORS 10 Cleaning pads
Summary of the content on the page No. 3
Putting your cleaner together Charging NOTE: Only use the charger supplied. CHARGE 24 HOURS BEFORE FIRST USE. Top view of cleaner Notch 3 To assemble the handle: To disassemble the handle: Use a ball point Connect the charger to a wall socket. Plug the charger end into the side of the unit. Insert the handle into the body of the unit and pen to push the button in while pulling the handle NOTE: Charge for 24 hours before first use. push down firmly until it locks into place. Be sure up and out of
Summary of the content on the page No. 4
Storage Recommended use 1 2 3 4 Use the storage hook to hang the cleaner up. Use the dry vacuum to remove loose dirt and debris Wet mop by dispensing the cleaning solution and NOTE: Hang in a place convenient for charging. from floors. using an absorbent pad to remove dirt and grime.
Summary of the content on the page No. 5
Operating the Vac ‘n’ Mop FOR ADVICE ON CLEANING SOLUTIONS AND ABSORBENT CLEANING PADS, PLEASE CALL VAX CARE ON 0870 6061248. NOTE: This product is intended for dry pick up only. Do not attempt to vacuum up any liquids with this cleaner. Prepare Vac’n’Mop 4 5 6 5 Lift the vacuum nozzle. It should lock into position. Place one absorbent cleaning pad on to the mop Push the vacuum nozzle back to the floor cleaning head of the unit. Secure by pushing the edge of the position. cloth into the tabs.
Summary of the content on the page No. 6
Operating the Vac ‘n’ Mop Prepare Vac’n’Mop 7 8 9 6 Unscrew the cap from the top of the cleaning solution Mix one cupful of the Multi Hard Floor cleaner per litre NOTE: If needed, the solution tank can be removed tank. of water and pour into the solution tank. Replace the from the body of the unit. When the bottle is removed cap on the solution tank. from the appliance, cleaning solution may be visible in the bottle recess. This is normal and will not cause any problems with your appliance. To r
Summary of the content on the page No. 7
Operating the Vac ‘n’ Mop Vacuum Mop 11 10 a 7 b c To turn the vacuum on: Push the on/off button down (a). For best results, clean one small area at a time. Spray the solution by holding the trigger down for 3-4 seconds. This will dispense enough solution to clean approx 1 To lock the vacuum on: Slide the lock button forward (b). square yard. Mop as you normally would, using the absorbent cleaning pad. NOTE: Pull back with the thumb to unlock. For tough spots and stains, spray the solution direc
Summary of the content on the page No. 8
Dust canister and filter: removal IMPORTANT: FOR BEST RESULTS, CLEAN THE FILTER AFTER EACH USE. FOR ADVICE ON FILTER REPLACEMENT, PLEASE CALL VAX CARE ON 0870 6061248 NOTE: This product is intended for dry pick up only. However, if a wet spill is accidentally vacuumed into the dust canister, the filter should be rinsed thoroughly, then allowed to air dry completely before re-using. 12 13 14 8 Press the dust canister release button located above Grasp the centre tab on the filter and pull it out
Summary of the content on the page No. 9
Dust canister and filter: removal 15 16 17 Slot 9 Tab Return the filter to the filter protector and return to the Re-attach by aligning the tab on the dust canister with Tilt and push the dust canister until it locks into place. dust canister. the slot on the body of the unit.
Summary of the content on the page No. 10
Troubleshooting WARNING: TO REDUCE RISK OF PERSONAL INJURY - UNPLUG CLEANER BEFORE SERVICING. POSSIBLE REASONS POSSIBLE CAUSES PROBLEM 1. Battery not charged. 1. Charge battery. For first use, charge for at least 24 Cleaner won’t run hours. 2. Handle not pushed into housing. 2. Make sure handle is pushed firmly all the way into housing and pin is visible in the hole in the body. 3. Battery dead - won’t hold a charge. 3. Call VAX CARE on 0870 6061248. 4. Needs service. 4. Call VAX CARE on 0870
Summary of the content on the page No. 11
Safety • Do not use or charge the unit outdoors. • Do not allow to be used as a toy. Close attention is necessary when used by or near children. • Use only as described in this user guidel. • Use only the manufacturer’s recommended attachments. • Do not use the charger with a damaged cord or plug. • Do not pull or carry by the cord, use the cord as a handle, allow the cord to come into contact with hot or sharp surfaces or close a door on the cord. • Do not unplug by pulling on the cord. • Do n
Summary of the content on the page No. 12
EEC STATEMENT OF COMPLIANCE Manufacturer/EEC importer: VAX Limited, hereby on our own responsibility declare that the product Vac ‘n’ Mop is manufactured in compliance with the following: Safety: 72/23/EEC Low Voltage Directive as modified by 93/68/EEC EMC: 89/336/EEC Electromagnetic compatibility Directive as modified by 93/68/EEC VAX Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 0QH, UK email: enquiry@vax.co.uk - website: www.vax.co.uk Version 1
