Summary of the content on the page No. 1
Office
Konnector
USER'S GUIDE
Copyright 1996 by KONEXX, Unlimited Systems Corporation, Inc. San Diego, CA .
Summary of the content on the page No. 2
Congratulations Your KONEXX Office Konnector is the ideal product for executives, sales people, and others who need data communications in the office. With your KONEXX Office Konnector, you can connect your modem, fax/modem, or fax machine to virtually any digital, PBX, multiline, or hotel telephone in seconds. Simply remove the coiled handset cord from the telephone base, connect the KONEXX Office Konnector to your telephone, then connect the handset (with coiled cord attached) and your comm
Summary of the content on the page No. 3
5. The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications in order to maintain uninterrupted service. If trouble is experienced with this equipment, please contact the service center for repair and/or warranty information. If the trouble is causing harm to the telephone network, the 6. tele
Summary of the content on the page No. 4
Getting started C hapter 1 describes the items you should have received with your KONEXX Office Konnector and any additional items you may need. Unpacking When you unpack your components, make sure you have all of the following items and that none of the items is damaged: ♦ One KONEXX Office Konnector. ♦ One AC adapter. If any items are missing or damaged, contact you
Summary of the content on the page No. 5
3. Connect a modular telephone cord from your modem, fax/modem, or fax machine jack labeled "Line" or "Wall" to the KONEXX Office Konnector jack labeled DATA. Connect the round end of the supplied AC adapter to the round connector next to the DATA jack and the other end to an AC outlet. Your installation should resemble the one shown in Figure 2-1. 5. Set the Telephone Level switch on the top of the KONEXX Office Konnector to 3. For more information, see Chapter 3. 6. Lift the telephone h
Summary of the content on the page No. 6
This chapter describes the purpose of the Telephone Level switch and how to set it for optimal operation. Overview Telephone Level The front of your KONEXX Office Konnector has a switch (see Figure 3-1). This switch lets you set the signal level from your modem or fax to the telephone. The Telephone Level switch can be set in any of four settings. The setting you use depends on the signal le
Summary of the content on the page No. 7
MANUFACTURER MODEL SWITCH AUTO- SEE SETTING DIAL NOTE System 75 3 Yes 3 & 4 System 85 3 Yes 3 & 4 Comdial Digitech 3 Yes Executech 3 Yes Impact 3 Yes MANUFACTURER MODEL SWITCH AUTO- SEE SETTING DIAL NOTE None David Systems 3--- 2 Specified None Eagle 2Yes Specified Ericcson MD110 3 Yes Executone Encore CX 3 No 8 IDS 3 No 8 Model 228 See Notes No 8 & 9 Model 432 See Notes No 8 & 9 Key Systems 2 or 3 Yes Fujitsu Focus 196 See Note No 5 Others 4 Yes GAI-Tronics Cohort 3 No 8 Harris Lanier 3 Yes Hit
Summary of the content on the page No. 8
MANUFACTURER MODEL SWITCH AUTO- SEE SETTING DIAL NOTE Macrotel 4 Yes 1 Mitel Superset 2 or 3 No 8 SX-200 3 No 1 & 8 NEC Determ II 1 or 4 Yes 1 Determ III 1 or 4 --- 2 Determ V 1 Yes Electra 2 or 3 No 8 Freedom 1 Yes Mark II 1 Yes Others 1 Yes Nitsuko Onyx 3 --- 1 & 2 Northcom Premier 3Yes (NC-1648) Northern Telcom Advantage 3 Yes 7 Focus 2 No 8 Logic One 3 No 8 Meridian 3 No 8 SL1 & SL100 Meridian 3 No 8 100 Northern Telcom Meridian 1 3 No 8 (continued) Norstar 3 Yes DR5 or DID 3 Yes Unity 2 or
Summary of the content on the page No. 9
MANUFACTURER MODEL SWITCH AUTO- SEE SETTING DIAL NOTE HCM-200 3 --- 1 & 2 Siemens Hicom (continued) Digital 1 --- 1 & 2 Saturn Digit 260 See Note --- 5 MANUFACTURER MODEL SWITCH AUTO- SEE SETTING DIAL NOTE Southwestern Bell Freedom 3 Yes Phone- Older 1 or 4 Yes 1 Freedom Phone- Newer Vision SRX 2--- 2 Phone Tadiran EKT 221 See Note Yes 9 Emerald 4 --- 2 & 9 Coral I & II 4 --- 2 & 9 Others See Note Yes 9 Telrad Model 816 4 Yes Model 2464 4 Yes Symphony 4 No 8 Digital 4 No 8 (818) 4 --- 2 Others T
Summary of the content on the page No. 10
MANUFACTURER MODEL SWITCH AUTO- SEE SETTING DIAL NOTE (Digital) 103 series 2 or 3 Yes Trillium Panther 2 or 3 --- 1 & 2 Talkto 616 2 --- 1 & 2 Vodavi Electronic See Note Yes 9 Key System MANUFACTURER MODEL SWITCH AUTO- SEE SETTING DIAL NOTE Walker Marathon 1 or 4 Yes Poet 1 Yes 1 ! If your telephone does not allow autodialing, you can still communicate by dialing with the keypad on your telephone. Refer to Chapter 4 for information on manual dialing. NOTES: 1. The KONEXX product may require
Summary of the content on the page No. 11
OR To make a connection using a fax machine, press its Start button. 4. Perform the data or fax transfer. When you finish, return the handset to the cradle. 5. To hang up a modem or fax/modem, use your software's call-termination feature, or type ATH0 and press Enter from direct connect mode. OR To hang up a fax machine, press its Stop button. ! The telephone handset is electronically disconnected when the modem goes off-hook. You must hang up your modem to restore use
Summary of the content on the page No. 12
! To operate properly, your modem must go off-hook and dial - even though you manually dialed the remote modem's telephone number. Your modem does not have to dial the entire telephone number; one digit is sufficient to complete the dialing process. 5. Perform the data transfer. When you finish, return the handset to the cradle. To hang up, use your communication software's call-termination feature, or type ATH0 and press Enter from direct connect mode. ! The telephone handset is electronically
Summary of the content on the page No. 13
______________________________ Receiving a data file_____________ When someone calls you to send a data file, use the following procedure to answer the call and receive the file. 1. If you will be using your communication software's manual answer or manual receive command to answer the call, skip to step 2. Otherwise, place your modem into direct connect (local terminal) mode. The manual that came with your communication software should explain this procedure. 2. When the telephone rings, lift
Summary of the content on the page No. 14
Your KONEXX Office Konnector must have AC power to operate in Data Mode. ♦ Use only the AC adapter supplied with your KONEXX Office Konnector. Do not use an adapter for a different device. ______________________________ Telephone Level switch__________ Telephone Level Make sure the switch is set properly. Otherwise, you will hear buzzing or squelching feedback through the modem speaker when the modem is off-hook, which will adversely affect transmission and reception. For information on usi
Summary of the content on the page No. 15
Some telephone systems (such as Rolm) do not use the standard dial tone, and your modem or fax/modem may not recognize the nonstandard tone as a dial tone. This command is also useful when the system being used will not accept autodialing (refer to Chapter 4). Table 3-1 on page 6 lists some telephones that do and do not support autodialing. ______________________________ Autodialing ________________ Some telephone systems will not support autodialing (the ability to have the modem/fax dia
Summary of the content on the page No. 16
Chapter 7 Specifications This chapter lists the operating and performance specifications. ______________________________ Operating specifications_________ Your KONEXX Office Konnector: ♦ Provides an RJ-11 connection at the handset jack of the telephone. ♦ Converts the 4-wire handset jack to a 2-wire RJ-11 jack. ♦ Transforms the handset impedance to telephone line impedance, and vice versa. ♦ Transforms the handset signal levels to modem signal levels, and vice versa. ♦ Uses the Telephon
